Advertisement
Air Quality Indicator
The PM2.5 indicator shows the real-time PM2.5 value. After powering on, it takes about 15 seconds to activate the PM 2.5 Indicator. The air quality indicator will illuminate and display the real-time PM2.5 value and corresponding air quality indicator color.
PM2.5 (µg/m )3 | AQI (EPA of USA) | Air Quality Indicator Color |
0.0-15 | 0-25 | Green (good) |
15-30 | 25-50 | Orange (moderate) |
30+ | 50+ | Red (unhealthy) |
Instant PM 2.5 value is one of the core references for the Indoor Air Quality Index (CAQI- Common Air Quality Index). With regard to working modes, Airthereal AGH430 air purifier will be implemented with the European EnvironmentProtection Agency (EPA).
For more information, please contact the European Environmental Protection Agency (EPA).
Know the 3-in-1 H13 HEPA Filter
When the replacement icon lights up (Filter icon keeps glowing), it is a reminder to check and change the air filter.
Recommend replacing the air filter every 6-8 months for optimal use, or according to your air filter status. It's time to replace the air filter when below symptoms appear:
Purchase a new Airthereal Air Filter Replacement: www.airthereal.com
Search on Amazon: AGH430 replacement filter / B08HYRJGWG
Only use Airthereal Glory Days AGH380 replacement filters for this unit.
Replace the Air Filter
Power off and unplug before operating.
Rotate the bottom cover counterclockwise and take out the old filter. Unwrap a new filter.
Install a new filter in the unit and rotate the cover clockwise.
Power the unit on. Press and hold the Power button for 5 seconds to reset the replacement reminder.
Unplug the power cord before cleaning.
Plastic housing should be cleaned with a soft cloth moistened with mild soap. Thoroughly remove soap film with a dry cloth.
For optimal maintenance, clean the unit every 2 months.
Problem | Cause | Solution |
No power or response | The unit is not plugged into an electrical outlet. | Connect the plug to a powered electrical outlet. |
The outlet is not working properly. | Try plugging the air purifier into a different outlet. | |
The power adapter is damaged. | Immediately discontinue use and contact Customer Support. | |
The air purifier is defective or malfunctioning. | ||
Unpleasant Smell | The filter may be too dirty if it's used for a long time. | Replace the filter. |
Using the air purifier in moist conditions or water entered in the filter. | ||
The air quality indicator always gets in red | Dirty filters and room air is bad. | Replace the filter. |
The numbers have been fluctuating from 3 to 15 | This PM2.5 sensor is very sensitive. | It means the air quality is good when the value is under 15. You need to pay attention when it goes higher than 30. |
Any faulty display of the LED numbers | Auto Mode has just been turned on. | Allow the air purifier to run for 10-15 seconds. They will change a stabilized status based on the detected air quality. |
The unit is defective or malfunctioning. | Immediately discontinue use and contact Customer Support. | |
Unusual noise while operating | Dirty filters. | Replace the air filters as instructed in the Replace the Air Filters section. |
Filters installed improperly. | Place the filter properly. Please refer to the Getting Started and Replacing the Air Filters section. | |
The foreign object inside the unit. | Immediately discontinue use and contact Customer Support. DO NOT attempt to open the air purifier yourself. | |
Flimsy or slanted surfaces resulting in an abnormal noise and vibrations. | Place the air purifier on hard, flat surfaces. | |
Significantly reduced airflow | Not enough space around the unit. | Ensure that there are at least 15 inches (38 cm) between the unit and other objects. |
Poor air purification quality | Surrounding area exceeds the applicable area. | DO NOT use the air purifier outdoors. This appliance is designed for indoor use only. |
The air inlet or outlet is blocked. | Remove objects that block the air inlet or outlet. | |
The filter is not properly placed in housing. | Properly place filter as noted in the Getting Started and Replacing the Filters section. |
Model | AGH430 |
CADR | 430 m³/h (252 CFM) |
Fan Speed | 5-Level |
Dust Sensor | Laser PM2.5 Particles Sensor |
Filter Structure | Pre-Filter, H13 Class True HEPA Filter, Activated Carbon Filter (attached with Nano Mineral, Cold Catalyst, Photo Catalyst and Molecular Sieve) |
UV Light | UV-C LED Wavelength: 270-275 nm Bulb life: Approx. 50,000 hours |
Noise Level | 22-49 dB |
Standby Power | 2 W |
Rated Power | 42 W |
Power Supply | AC 120-240 V to DC 24 V Power Adapter (Length: 2 M / 6.5 ft) |
Operating TEMP | 15°F ~ 130°F (-10°C ~ 55°C ) |
Please read and comply with all of the instructions and warnings in the manual before using. Failure to comply with the instructions and warnings provided herein may result in inaccurate results and/or damage to the product itself.
General Safety
Only use this air purifier as described in this manual.
Use & Care
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Airthereal Glory Days AGH430 - HEPA Air Purifier Manual
Advertisement
Need help?
Do you have a question about the Glory Days AGH430 and is the answer not in the manual?
Questions and answers