Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco eXmark PRO 12
Summary of Contents for Peco eXmark PRO 12
- Page 1 P P P P P P PRO 12 ENGINE DRIVEN - PECO PECO PECO PECO PECO GRASS COLLECTION SYSTEM Model# 35621228 EXMARK NEXT GENERATION MOWERS Deck Size: 48”, 52”, 60” & 72” Mower Year: 2009-2023 OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0384 Rev.
-
Page 2: Table Of Contents
GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Blower Cone Installation - - - - - - - - - - - - - - - - - - - 9 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 Impeller Blade Removal/Replacement - - - - - - - - - - 9... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
6. REMEDIED EXCLUSIVE: The only remedies the purchaser has in connection with the breach or performance of any warranty on New PECO, Inc. consumer products are set forth above. In no event will New PECO, Inc. be liable for special incidental or consequential damages. -
Page 5: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION Introduction Description We are pleased to have you as a PECO customer. Your The collection system is designed for turf maintenance collection system has been designed to give you a low where there is a need to collect the grass clippings as maintenance, simple and effective way to collect the the mower cuts the turf. -
Page 6: Lower Main Frame Leg Installation
Lower Main Frame Leg Installation Figure C Looking from the rear of mower, locate the ROPS Left Lower Frame Leg mounting bolts and remove the lower hex bolt and B0529 washer from each side of the ROPS. On the mowers Attach to R.O.P.S. -
Page 7: Lift Handle Installation
Lift Handle Installation Figure A The various parts of the Handle Assembly P#(A0273) must be attached to the container frame. PAGE 12 Insert Pins Insert Pins shows the orientation and location of the components. From Outside From Outside Slide the Lift Handle into the slot in the Handle Mount Bracket P#(B1730) on the grass container. -
Page 8: Engine Mount Arm Assembly Installation
ngine Mount Arm Assembly Boot To Mower Deck Installation Installation To mount the Boot Plates P#(B0538) to the Boot P#(E1039) use (2) 3/8”-16 x 1” Carriage Bolts P#(K1182) Slide the Engine Mount Arm Assembly P#(A0318) and (2) 3/8”-16 Nyloc Nuts P#(K1216). Make certain that (Figure A) into the Outer Engine Mount Tube P#(A0600) when bolting the Boot and Boot Plate together, that the until the hole in the Engine Mount Arm Assembly aligns... -
Page 9: Blower Cone Installation
Blower Cone Installation 5/16”-18 x 2-1/2” Figure A All Thread HHCS Thread (1) 5/16”-18 Jam Nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially thread the bolts into each of the two tabs located on the Blower Housing. -
Page 10: Throttle Cable Installation
Throttle Cable Installation Figure D To install the Throttle Cable Kit P#(A0060) to the Box Assembly, align the large end of the slot in the Throttle Base Plate (Figure A) with the rivets located on the front of the Box Assembly Frame (Figure B). Place the Throttle Base Plate over the rivets, Slide the Throttle Throttle Cable Cable Kit to the right, moving the smaller end of the slot... -
Page 11: Length Of Hose Adjustment
Length Of Hose Adjustment Figure B The hoses in the following steps must be cut to fit your Inlet machine. Do not cut the hoses until you have tried to fit them on your machine. Remember that the hoses need to be long enough to allow for the opening and closing of Upper Hose the collection system as well as allowing ample clamping... -
Page 12: Exploded Parts Views And Assemblies
Lift Handle Assembly Aluminum Grass Container Assembly Inlet Aluminum Grass Container With Handle Attached Latch Hook Mechanism Assembly MAIN FRAME... -
Page 15: Safety Decals
SAFETY DECALS To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. P P P PECO... -
Page 16: Operating Instructions
SECTION III OPERATING INSTRUCTIONS Disengagement Of The EDrive Assy General Safety A. To disengage the EDrive assembly, move the Only qualified people familiar with this operator’s manual Rocker Switch to the off position. and the mower’s operator’s manual should operate this machine. -
Page 17: Parts And Service
If for any reason your Service Center been torn or worn through, replace immediately. is unable to service your collection system or supply replacement parts, contact New PECO, Inc. and include After Each Use: the following information on the chart below. -
Page 19: Troubleshooting
Troubleshooting 2017 (v1.0) Collection System Performance Problem Possible Cause Corrective Action — Cutting blades are bent or — Install new cutting blade unbalanced — Loose blower pulley or pulley Abnormal Vibration — Tighten the pulley assembly — Contact dealer to replace —... - Page 20 P P P P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...