Name of selling dealer Date of Purchase from To register your warranty coverage selling dealer with Richmar, fill out the online form at: Product Serial Number richmarweb.com/warranty-registration Reason for return RICHMAR SHALL RESERVE THE RIGHT The return Authorization Number must...
Page 4
Heating Unit, please read this instructions at any time without obligation manual thoroughly and follow all instructions on the part of Richmar. SYMBOLS GLOSSARY NOTE: Throughout this manual, “NOTE” CAUTIONS may be found.
+/- 1-2° F new heat packs absorb water. • ALWAYS NOTE: Richmar DOES NOT recommend water temperature to stabilize prior to using other heat pack products, as we temperature readings. have not tested the safety of those heat •...
Page 6
(65°C) turn the unit OFF, remove the of hydrocollator approved heat packs, Power Cord and quarantine the unit. please use manufacturers covering Contact Richmar Technical Service for recommendations. further instructions. NOTE: For further information on avoiding electrical interference, refer to •...
DETAILED DEVICE DESCRIPTION Rear View Front View Time Clock Date Current Device Temperature Desired Set Temp (Default is set to 135˚F) Settings Menu Main Screen Display Side View Power Switch Main Fuse 6 Amp Power Supply Receptacle Drain Hose Attachment Enclosure Panel...
CONTENTS & REORDER INFORMATION Item # Description HT-R6-DT HydraTherm DT Heating Unit HT-DT-WP HydraTherm DT with 6 Standard Heat Packs DT-RACK HydraTherm Finned Rack System HT-R6-X HydraTherm DT Power Cord DT-HOSE HydraTherm DT Drain Hose DT-FILTER HydraTherm DT Drain Filter RACK ASSEMBLY AND RECOMMENDED PACK SET UP The HydraTherm DT unit comes standard Ensure that the keyed...
When purchasing your HydraTherm DT Heating Unit, Richmar recommends two Figure 2: For the variety size configuration, different pack configurations that will fit fold the cervical and oversize pack and the into your device.
The unit will go through a self- test check and will display a start up screen showing the Richmar logo and then automatically switch to the Home Screen. To change the desired settings, press the up or down arrow on the keypad to highlight the selection in blue.
Page 11
DEVICE USER INTERFACE pad to change the minutes and Press the up or down arrow until the right arrow again to change you reach the correct number for to either morning or afternoon. the chosen format then the right arrow on the keypad to accept and advance to the next number until correct date is entered.
DRAIN INSTRUCTIONS WARNING ALWAYS unplug the unit from the electrical outlet when cleaning the unit. ALWAYS allow the heating unit to cool down before moving. It is NOT recommended to move the tank when filled with water, as it can cause water to overflow out of the tank and possibly cause damage to the electrical outlet and your facility.
*NOTE: Temperature reading from external thermometers may differ from displayed temperature based on location of temperature reading, and type of thermometer used. If in any case the suggested Troubleshooting Solutions DO NOT remedy the problem(s) you are experiencing, contact Richmar Tech Support for additional information.
Page 14
ERROR CODES In the event an Error Code is displayed on the screen, reference the error code chart below. From the home screen, press the right arrow to enter the Settings Menu. Press the down arrow to ERRORS is highlighted blue. Press right arrow to accept. Depending on the displayed error code, chose from the Error #’s to determine problem and solution.
Page 15
ERROR CODES In the event an Error Code is displayed on the screen, reference the error code chart below. From the home screen, press the right arrow to enter the Settings Menu. Press the down arrow to ERRORS is highlighted blue. Press right arrow to accept. Depending on the displayed error code, chose from the Error #’s to determine problem and solution.
RECOMMENDED CLEANING & STORAGE Turn unit off to let the water and WARNING packs cool to room temperature. ALWAYS unplug the unit from the NOTE: DO NOT attempt to clean the electrical outlet when cleaning the unit. debris or drain the tank with hot water. DO NOT attempt to clean the debris or Remove packs and finned rack from drain the tank with hot water...
APPENDIX A - EMC TABLES Guidance and Manufacturer’s Declaration – Electromagnetic Immunity The Hydratherm tank is intended for use in the electromagnetic environment specified below. The customer or the user of the Hydratherm tank should assure that it is used in such an environment.
Page 19
APPENDIX A - EMC TABLES GUIDANCE AND MANUFACTURER’S DECLARATION – ELECTROMAGNETIC IMMUNITY The Hydratherm tank is intended for use in the electromagnetic environment specified below. The customer or the user of the Hydratherm tank should assure that it is used in such an environment Immunity test IEC 60601 test level...
Page 20
APPENDIX A - EMC TABLES GUIDANCE AND MANUFACTURER’S DECLARATION – ELECTROMAGNETIC IMMUNITY The Hydratherm tank is intended for use in the electromagnetic environment specified below. The customer or the user of the Hydratherm tank should assure that it is used in such an environment Immunity test IEC 60601 test level...
Page 21
APPENDIX A - EMC TABLES GUIDANCE AND MANUFACTURER’S DECLARATION – ELECTROMAGNETIC IMMUNITY The Hydratherm tank is intended for use in the electromagnetic environment specified below. The customer or the user of the Hydratherm tank should assure that it is used in such an environment Immunity test IEC 60601 test level...
Page 22
APPENDIX A - EMC TABLES RECOMMENDED SEPARATION DISTANCES BETWEEN PORTABLE AND MOBILE RF COMMUNICATIONS EQUIPMENT AND THE E360T-SY-IN Ventilator The Hydratherm tank is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the Hydratherm tank can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the Hydratherm tank as recommended below, according to the maximum output power of...
Need help?
Do you have a question about the HydraThermDT and is the answer not in the manual?
Questions and answers