Table of Contents
Advertisement
1. INSTRUCTIONS FOR USE ................................................................ 4
2. SAFETY PRECAUTIONS ................................................................... 6
3. ENVIRONMENTAL CARE................................................................... 8
4. DESCRIPTION OF CONTROLS......................................................... 9
5. USING THE HOB.............................................................................. 10
6. CLEANING AND MAINTENANCE.................................................... 14
7. POSITIONING IN THE COUNTER TOP .......................................... 16
8. ELECTRICAL CONNECTION........................................................... 19
9. GAS CONNECTION ......................................................................... 20
10. ADAPTATION TO DIFFERENT TYPES OF GAS ............................ 22
THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES
WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS
MANUAL.
INSTRUCTIONS FOR THE USER: these contain user advice, the description
of the controls and the correct procedures for cleaning and maintenance of
the appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must install the appliance, set it functioning and carry out
an inspection test.
@
Further information about the products can be found at www.smeg.com
Contents
3
Advertisement
Table of Contents
Related Manuals for Smeg P1640X
Summary of Contents for Smeg P1640X
-
Page 1: Table Of Contents
WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS MANUAL. INSTRUCTIONS FOR THE USER: these contain user advice, the description of the controls and the correct procedures for cleaning and maintenance of the appliance. INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test. -
Page 2: Instructions For Use
General instructions 1. INSTRUCTIONS FOR USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE HOB. -
Page 3: General Instructions
General instructions NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE COOKING HOB PAN STANDS. NEVER USE CONTAINERS WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE HOB. -
Page 4: Safety Precautions
AND BRAND NAME IS IN A VISIBLE POSITION UNDER THE CASING. DO NOT REMOVE THE PLATE ON THE CASING FOR ANY REASON. BEFORE CONNECTING THE APPLIANCE, ENSURE THAT IT IS SET TO THE TYPE OF GAS THAT IT WILL BE SUPPLIED WITH, CHECKING THE LABEL APPLIED UNDER THE CASING. - Page 5 General instructions DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR PLAY WITH IT AT ANY TIME. DO NOT INSERT POINTED METAL OBJECTS (CUTLERY OR UTENSILS) INTO THE SLOTS IN THE APPLIANCE. DO NOT USE STEAM JETS FOR CLEANING THE APPLIANCE.
-
Page 6: Environmental Care
You can obtain the addresses of collection, recycling and disposal centres from your retailer or from the competent local organisations. Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. -
Page 7: Description Of Controls
Instructions for the user 4. DESCRIPTION OF CONTROLS Control zone All the hob controls are grouped together on the front panel. CONTROL ZONE 4-burner hob 5-burner hob KNOB DESCRIPTION To light the flame, press the knob and turn it anti-... -
Page 8: Using The Hob
A in the flame-spreader crowns. Positioning the pan stands The pan stands are provided unassembled on the hob. The list of available pan stand types are listed below. Side pan stands (5 burners) - Page 9 Make sure that the pan stands are simply centred on their respective burners, without forcing the burners to be raised or tilted. If they are, repeat the positioning procedure. If you find that a pan is particularly unstable, make sure that the pan stands have not been positioned incorrectly.
- Page 10 Hold down the knob for about 2 seconds to keep the flame lit and to activate the safety device. The burner may go out when the knob is released. If this happens, repeat the procedure, holding the knob down for longer.
- Page 11 Using the griddle A few precautions are necessary if you wish to use a griddle: • leave a gap of at least 160 mm between the edge of the griddle and the side wall; • if one of the burners close to the wooden rear wall is a triple crown burner, leave a gap of at least 160 mm between this wall and the edge of the griddle;...
-
Page 12: Cleaning And Maintenance
To clean and preserve surfaces, always use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or a microfibre cloth. - Page 13 The burner pins A must be inserted in the housings B in the burner crown. The holes C in the burner crowns should be slid over the igniters and thermocouples D on the hob.
-
Page 14: Positioning In The Counter Top
(T 90°C). If installed on top of an oven, the latter must be equipped with a cooling fan. Section cut from the work surface Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear edge. - Page 15 Carefully position the supplied insulating seal on the outer perimeter of the hole made in the counter top as shown in the figure below, trying to make it stick on the entire surface by applying light pressure on it with your hands (See the dimensions indicated in the figure).
- Page 16 To secure the hob correctly to the counter top, tighten the brackets A in the appropriate holes on the sides of the casing. Take care while securing with the brackets; if tightened too much the glass may be strained causing it to crack.
-
Page 17: Electrical Connection
Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. -
Page 18: Gas Connection
The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. For supplying it with other types of gas, see chapter "10. ADAPTATION TO DIFFERENT TYPES OF GAS". - Page 19 Use a pressure regulator and make the connection on the gas cylinder following the guidelines set out in the regulations in force. Make sure that the feed pressure complies with the values indicated in the table at point “10. ADAPTATION TO DIFFERENT TYPES OF GAS”.
-
Page 20: Adaptation To Different Types Of Gas
Before carrying out the following operations, disconnect the appliance from the power supply. The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. If other types of gas are to be used, the nozzles must be replaced and the primary air must be adjusted. - Page 21 Lift the hob top upwards. 10.2 Adjustment for LPG Loosen screw A and push support B all the way. Using a a double head, remove nozzle C and replace it with the appropriate nozzle, following the instructions in the tables for the type of gas to be used. The nozzle tightening torque must be no more than 3 Nm.
- Page 22 Instructions for the installer 10.3 Adjustment for natural gas The hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. To reset the appliance for operation with this type of gas, carry out the same steps as described in “10.2 Adjustment for LPG”, but select the nozzles and adjust the...
- Page 23 Ultra-rapid (5) Internal Double crown (6) External To identify the burners on your hob, refer to the drawings in “10.6 Arrangement of the burners on the cooking hob”. 10.5 Final operations After making the adjustments described above, reassemble the appliance by following the instructions in “10.1 Removing the hob top”...
- Page 24 5. Ultra-rapid 6. Double crown 10.7 Lubrication of gas taps Over time the gas taps may become difficult to turn and get blocked. Clean them internally and replace the lubrication grease. This procedure must be carried out by a specialised technician.