Table of Contents
Advertisement
1. Precautions for safety and use ________________________ 20
2. Fitting the appliance in the top ________________________ 21
2.1 Fixing to the supporting structure _______________________________________21
3. Electrical connection ________________________________ 23
4. Gas connection____________________________________ 24
4.1 Bottled gas connection _______________________________________________25
4.2 Room ventilation ____________________________________________________25
4.3 Combustion gas discharge ____________________________________________25
5. Adapting to different types of gas ______________________ 26
5.1 Removing the hob skin _______________________________________________26
5.2 Adjusting for bottled gas ______________________________________________27
5.3 Adjusting for town gas _______________________________________________27
5.4 Adjusting for natural gas ______________________________________________28
5.5 Adjusting the primary air flow __________________________________________28
5.6 Reassembling the hob skin____________________________________________28
5.7 Adjusting the minimum setting for natural gas and town gas __________________29
5.8 Adjusting the minimum for bottled gas ___________________________________29
5.9 Hob burner layout ___________________________________________________29
5.10 Greasing the gas taps________________________________________________29
6. Description of controls ______________________________ 30
6.1 The front panel _____________________________________________________30
7. Using the hob _____________________________________ 31
7.1 Lighting burners with safety device______________________________________31
7.2 Positioning the griddle plate ___________________________________________31
7.3 Practical hints for using the burners _____________________________________31
7.4 Pan diameters______________________________________________________32
8. Cleaning and maintenance ___________________________ 33
8.1 Cleaning stainless steel ______________________________________________33
8.2 Cleaning the components _____________________________________________33
THESE INSTRUCTIONS ONLY APPLY TO THE COUNTRIES OF DESTINATION WHOSE
IDENTIFICATION SYMBOLS ARE LISTED ON THE COVER OF THIS MANUAL.
THIS BUILT-IN HOB IS CLASSIFIED AS CLASS 3.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
engineer who is to check the gas supply system and install, commission and test the
appliance.
INSTRUCTIONS FOR THE USER: these provide recommendations for use, a
description of the controls and the correct procedures for cleaning and maintaining the
appliance.
Table of Contents
19
Advertisement
Table of Contents
Related Manuals for Smeg GKL64-3
Summary of Contents for Smeg GKL64-3
-
Page 1: Table Of Contents
Table of Contents 1. Precautions for safety and use ________________________ 20 2. Fitting the appliance in the top ________________________ 21 2.1 Fixing to the supporting structure _______________________________________21 3. Electrical connection ________________________________ 23 4. Gas connection____________________________________ 24 4.1 Bottled gas connection _______________________________________________25 4.2 Room ventilation ____________________________________________________25 4.3 Combustion gas discharge ____________________________________________25 5. -
Page 2: Precautions For Safety And Use
Precautions for Safety and Use Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB. -
Page 3: Fitting The Appliance In The Top
Instructions for the Installer Fitting the appliance in the top The procedures required below must be carried out by a skilled builder and/or joiner. The hob can be installed on various materials, including masonry, metal, solid wood and wood finished with plastic laminates, provided the material is heat-resistant (T 90°... - Page 4 Instructions for the Installer Fit the insulating gasket provided carefully around the outside edge of the hole made in the top as shown below, pressing it down with your hands so that its entire surface fits snugly. Follow the dimensions shown, depending on the model of hob to be installed, bearing in mind that on both models the long front edge must be flush with the hole.
-
Page 5: Electrical Connection
Instructions for the Installer Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. -
Page 6: Gas Connection
Instructions for the Installer Gas connection If the appliance is installed above an over, the gas hose must be passed around the back of the oven to prevent overheating. The connection to the gas mains may be made using a copper pipe or a continuous-wall steel hose in accordance with the relevant regulations. -
Page 7: Bottled Gas Connection
Instructions for the Installer Bottled gas connection Use a pressure regulator and make the connection to the gas cylinder in accordance with the relevant regulations. Make sure that the gas supply pressure is as stated in the table in point "5.2 Adjusting for bottled gas". Room ventilation The appliance may only be installed in a permanently ventilated room as specified by the relevant regulations. -
Page 8: Adapting To Different Types Of Gas
Instructions for the Installer Adapting to different types of gas Before carrying out the operations described below, disconnect the appliance from the electricity supply. The hob is tested with G20 (2H) natural gas at the pressure of 20 mbar. If it is to be used with other types of gas, the burner nozzles have to be changed and the primary air flow adjusted. -
Page 9: Adjusting For Bottled Gas
Instructions for the Installer Adjusting for bottled gas Undo the screw A and push the support B fully down. Remove the nozzle C with a spanner and fit the suitable one following the instructions in the tables referring to the type of gas to be used. -
Page 10: Adjusting For Natural Gas
Instructions for the Installer Adjusting for natural gas The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. To return the appliance to the condition required to use this type of gas, proceed as described in point “5.2 Adjusting for bottled gas”... -
Page 11: Adjusting The Minimum Setting For Natural Gas And Town Gas
Instructions for the Installer Adjusting the minimum setting for natural gas and town gas Reassemble the components on the burner and fit the knobs onto the tap rods. Light the burner and turn it to the minimum Remove the knob again and adjust the regulator screw inside or beside the tap rod (depending on the model) until an even minimum flame is obtained. -
Page 12: Description Of Controls
Instructions for the User Description of controls The front panel All the hob's control and monitoring devices are placed together on the front panel. KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol . -
Page 13: Using The Hob
Instructions for the User Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob. -
Page 14: Pan Diameters
Instructions for the User Pan diameters BURNERS 1 Auxiliary 2 Semi rapid 3 Rapid 4 Double flame 5 Ultra rapid 6 Rapid 7 Rapid 8 Double flame min. and max. Ø (in cm) 7-18 10-24 18-24 12-28 20-28 18-24 18-24 12-30... -
Page 15: Cleaning And Maintenance
Instructions for the User Cleaning and maintenance Before carrying out any operations, disconnect the appliance from the electricity supply. Cleaning stainless steel To keep the hob in good condition, it must be cleaned regularly, after each use, first allowing it to cool. 8.1.1 Routine daily hob cleaning When cleaning and caring for stainless steel surfaces, always use only specific...