Table Of Contents - Bernina arista 165 Service Manual

Contents (mechanic)
2
Safety regulations
Adjustment of BERNINA artista
Technical data of the Bernina artista
series 165/170/180/185
Removing covers
Tensioning the drive belts
Checking the bobbin winder unit
Checking the presser foot fixation
Checking the presser foot height
Checking the darning foot height
Distance needle/hook
Needle plate position
Needle position zig-zag
Synchronisation disc
Feed-dog position (165/170)
Feed-dog position (180/185)
Height of the feed-dog
Thread passage play (165/170)
Setting the driver (165/170)
Radial play of the driver (165/170)
Loop lift (165/170)
Loop lift (180/185)
Needle height
Bobbin case stopper (180/185)
Feed-dog Synchronisation
Basic setting of balance
Basting/long stitch device
Knee lifter unit
Lowering the lifter lever
Automatic threader (180/185)
Lower thread tension
Upper thread tension (165/170)
Upper thread tension with a weight
Upper thread tension rough tuning
Upper thread tension fine tuning
Thread regulater spring
Thread cutter
Embroidery module function and
troubleshooting
Test sample evaluation
Embroidery; removing covers
Belt drive of x- and y-carriages
Exchanging S-Print
Exchanging X-Carriage Stepping Motor
Exchanging X-Carriage Stepping Motor
Removing covers
Main cable
Freearm sensor and cable
S-Print
X-Carriage Stepping Motor
X-Carriage Belt and Gear Wheels
Y-Carriage Sensor
Y-Carriage Stepping Motor
Y-Carriage Belt and Gear Wheels
Embroidery Modul - Adjustment
Set Hoop Support on Y-Profile
Contents (electronic)
Page
1 Description
3 Block diagram a165/170/180
Blockdiagram a185
3 L-print 165/170/180 (old)
5,6,7 L-print 165-185 (new)
8 S-print 165-180
9 S-print 185
9 Diagnostic instruction
10 Electrostatic discharges
10 Exchanging the S-print/touch screen
11 Test program artista
11 Test programs
12 Test no.1 Sewing-off
12 Test no. 2Forward/reverse feed equa-
13 lization
13 Mechanical fine adjustment
14 Test no.3 Stepping motor test for
14 sewing machine (balance).
15 Test no.4 Pinning position of all step
15 ping motors
16 Test no.5 LCD/Touch-screen test
17 Test no.6 Touch screen calibration
18 Test no.7 Configuration of the sewing
18 machine
19 Test no.8 Maximum speed equalisation
19 in stitches/minute
20 Test no.9 Both lower and upper thread
21 detectors
21 Test no.10 Endurance test for R+D
21 Test no.11 Software version of the
22 sewing machine
22 Test no.12 Beeper test (acoustically)
23 Test no.13 Embroidery
23 Test no.13a Stepping motor test
23 Test no.13b Setting of reference point
24 Test no.13c X-carriage sensor test
24 Test no.13d Y-carriage sensor test
43 Test no.13e Software version display
Test no.13f Memo card
44 Test no.13g Free-arm Eembroidery
45 Test no.14 Demo mode
46 Test no.15 Buttonhole
46 Test no.16 Basting solenoid
47 Test no.17 Clamp magnet
47 Test no.18 Thread cutter
48 Test P-Print
49 Test Buttonhole sensor
50 RET-Print
51 Test Switch bobbin winder unit
52 Tests in basic position
53 Presser foot lowering check
54 Feed-dog drop
55 Thread cutter key
56 Threader sensor
57 Foot control and needle stop change
57 using the foot control
Motor power
Hour counter
Stitch counter
Test Connection S-print/L-print
Page
25
26
27
28
29
30
30
31
31
32
32
33
34
34
34
35
35
35
35
36
36
36
37
37
37
37
37
38
38
38
38
38
39
39
39
39
39
39
40
40
40
40
41
41
41
41
41
41
42
42
42
42