Bosch WEU PST 10,8 LI Original Instructions Manual page 13

OBJ_BUCH-1842-002.book Page 13 Monday, November 10, 2014 12:58 PM
Technical Data
Jigsaw and Sabre Saw
Article number
Rated voltage
Stroke rate at no load n
0
Tool holder
Stroke rate control
Stroke
Max. cutting depth
– in wood
– in gypsum board
– in plastic
– in aluminium
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
1)
– during operation and during
storage
Recommended batteries
Recommended chargers
1) Limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a =6 m/s , K=1.5 m/s
h
2
Cutting sheet metal: a =8 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
PST 10,8 LI
scribed under "Technical Data" is in conformity with all rele-
3 603 CB4 0..
vant provisions of the directives 2009/125/EC (Regulation
V= 10,8
1194/2012), 2011/65/EU, 2014/30/EU, 2006/42/EC in-
-1 cluding their amendments and complies with the following
min 0–2200
standards: EN 60745-1, EN 60745-2-11.
SDS
Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,
mm 12
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
mm 30
Executive Vice President
mm 24
Engineering
mm 10
mm 2
kg 1.1
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 16.10.2014
°C 0...+45
°C –20...+50
Assembly
PBA 10,8V...
 Before any work on the machine itself (e. g. mainte-
AL 11..
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Battery Charging
 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
2
,
The lithium-ion battery can be charged at any time without re-
2
.
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Removing the battery
To remove the battery 2, press the unlocking buttons 1 and
pull the battery out of the machine to the rear. Do not exert
any force.
Replacing/Inserting the Saw Blade
 When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Selecting a Saw Blade
Use only saw blades suitable for the material being worked.
Use only T-shank saw blades. The saw blade should not be
longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
 Avoid skin contact when you want to replace a saw
blade and wear protective gloves. The saw blade can be-
come hot during prolonged use.
English | 13
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 0RJ | (10.11.14)