Page 1
100 psi (7 bar) Maximum Working Pressure NOTE: See page 5 for gun washer descriptions. 03298 03297 03299 Model 112634 Model 112635 Model 112636 GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 ECOPYRIGHT 1999, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001...
D Read all instruction manuals, tags, and labels before operating the equipment. D Use the equipment only for its intended purpose. D Do not alter or modify this equipment. Use only genuine Graco parts and accessories. D Check the equipment daily. Repair or replace worn or damaged parts immediately.
Page 4
WARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and result in fire or explosion and serious injury. D Ground the equipment. See Grounding on page 8. D Provide fresh air ventilation to avoid the buildup of flammable fumes from the solvent. D Extinguish all the open flames or pilot lights in the gun washer area.
To customize the gun washer, order one kit for each cleaning station. Kit Includes Kit Part No. Typically Used to Clean Part No. Description 236659 Graco air-assisted airless electrostatic guns 195903 Air cap blank 188406 Tip housing 183459 Washer (2)
Page 7
Dimensions 03299 03297 Model 112636 Model 112634 and 112635 Model Measurements, inches (mm) B–with lid B–with lid closed opened 112634 and 20.75 42.25 61.00 20.50 16.25 25.12 112635 (527) (1073) (1549) (521) (413) (638) 112636 19.25 40.5 55.00 23.00 18.00 24.5 (489) (1029)
Installation Install the Gun Washer Connect the Air Line WARNING 1. Install an air pressure regulator (D) on the gun washer air supply line to control air pressure to the gun washer. See Fig. 2. FIRE HAZARD To prevent hazardous concentrations of flammable and/or toxic vapors, the gun 2.
Operation Pressure Relief Procedure WARNING WARNING TOXIC FLUID HAZARD Hazardous fluids or toxic fumes can cause serious injury or death if splashed PRESSURIZED EQUIPMENT HAZARD in the eyes or on the skin, swallowed, or The system pressure must be manually relieved to inhaled.
Page 11
The PRO-Washt gun washer is approved to clean the 1. Remove the pressure cup or fluid line and the air Graco PRO 3500, PRO 4500, and PRO AA4500 elec- line from the spray gun. trostatic guns. Consult the manufacturer of any other electrostatic gun before using the PRO-Wash.
Page 12
Operation Placing Cups and Pots in the Gun Washer the kit (Manual 308414) to install and use this option. See page 5 for kit description. 2 Quart Pressure Cups Container: Set the pressure cup over the spray nozzle. Refer to Fig.
Page 13
Operation Models 112635 and 112636 -- Using the Hose Wash Hose Wash 1. Place the hose entirely inside the gun washer. 2. Connect one end of the hose to the hose wash Hose Wash bulkhead fitting. See Fig. 4. Bulkhead Fitting 3.
Page 14
Operation Operating the Gun Washer 2. Make sure all adapter chains and cables are inside the gun washer tank. WARNING 3. If one or more of the gun mounts is not being used, place a stream blocking device, such as a PRESSURIZED EQUIPMENT HAZARD pint-size can, over the stem supports and the cup Do not operate the gun washer with the...
Shutdown and Care Gun Washer Shutdown and Care Air Cut-off Switch and Reset Block WARNING WARNING PRESSURIZED EQUIPMENT HAZARD To reduce the risk of an injury from accidental EQUIPMENT MISUSE HAZARD spray, splashing fluid, or moving parts, follow the A safety device has been installed to shut off the Pressure Relief Procedure, covered in steps 1 pump when the gun washer lid is opened.
Page 16
Shutdown and Care Check the Gun W asher Electrical Continu- Check your local electrical code for detailed grounding instructions for your area and type of equipment. If electrical continuity is lost, check the grounding con- WARNING nections and reconnect them as needed. See Fig. 6 for the gun washers grounding circuits.
Parts for Model 112634 Reference Fluid Manifold Detail Pump Ground Bar Detail NOTE: The circled letters indicate the continuation points of illustra- tions of tubes or wires. Ref. A 03309 308393...
Page 19
Parts for Model 112634 Model 112634 Gun Washer Ref. Ref. Part No. Description Qty. Part No. Description Qty. 112871 OUTLET TUBE, pump 512802 TRIGGER LOCK, wire; 512803 SWITCH, air cut-off stainless steel 112870 INTAKE TUBE, pump 512835 ADAPTER, gun fluid inlet; brass 512804 BLOCK, reset valve 512867...
Page 20
Parts for Model 112635 Reference Fluid Manifold Detail Pump Ground Bar Detail NOTE: The circled letters indicate the continuation points of illustra- tions of tubes or wires. Ref. A 03310 308393...
Parts for Model 112635 Model 112635 Gun Washer Ref. Ref. Part No. Description Qty. Part No. Description Qty. 112871 OUTLET TUBE, pump 512802 TRIGGER LOCK, wire; 512803 SWITCH, air cut-off stainless steel 112870 INTAKE TUBE, pump 512835 ADAPTER, gun fluid inlet; brass 512804 BLOCK, reset valve 512867...
Page 22
Parts for Model 112636 Reference Fluid Manifold Detail Pump Ground Bar Detail Ref. A NOTE: The circled letters indicate the continuation points of illustrations of tubes or wires. 03311 308393...
Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.