Advertisement
GENERAL_
• Select a source by pressing one of the source select keys
on the remote control or the amplifier.
• Adjust the volume with VOLUME 5 or on the remote control.
• Select the desired equalizer preset by pressing PRESET 13
or FLAT 14.
• Select the desired sound effect by pressing DSP 16 or SUR¬
ROUND 7. The display shows whether SURROUND or DSP
is selected.
• Press DBB 6 if you want to enhance the bass tones {vol¬
ume-position-dependent). The DBB 6 key will light up if
DBB is selected.
Notes:
-
DSP 16 will be switched off automatically when you switch
on SURROUND 7. In order to avoid unwanted sound
effects, you cannot use DSP and SURROUND at the same
time.
- The surround sound effect cannot be obtained with mono¬
phonic signals.
- The surround sound effect can increase noise in the case
of weaker FM stations.
SYSTEM POWER OFF/STANDBY
• Press SYSTEM POWER OFF/STANDBY 1 to switch on the
power. The system will enter the standby mode. The tuner
display shows the current day and time and the red indicator
on VOLUME 5 will light up.
• Press SYSTEM POWER OFF/STANDBY 1 again to switch off
the power.
STANDBY_
The standby mode is a kind of sleeping mode. It is possible to
wake up (a part of) the system by pressing a source selection
button on the remote control or on the amplifier.
Wake-up from standby:
There are several options to wake the system up from standby:
• Select a source on the amplifier by pressing DCC 10. The
amplifier and the (optional) DCC recorder will wake up from
standby.
• Select a source on the remote control by pressing a source
selection key for less than 1 second. Only the selected
source wakes up from standby, the amplifier stays in stand-
by.
• Select a source on the remote control by pressing a source
selection key for longer than 1 second Both the selected
source and the amplifier will wake up.
Notes:
~ When the tuner is selected it will always wake up both the
tuner and the amplifier, even if the tuner select key is
pressed for less than 1 second.
- It is also possible to wake up the units by pressing defined
wake-up keys on the units (see the descriptions of the units).
Putting (part of) the system in standby
• To put the whole system into the standby mode, press the
STANDBY button on the remote control for longer than 1
second. The display of the tuner will switch to low bright¬
ness; the other displays will be switched off. The red indica¬
tor on the volume knob will not go out.
• To put a selected unit into standby mode: press the source
selection key for less than 1 second and press the STANDBY
button on the remote control also for less than 1 second.
The display of the selected unit will be switched off.
If the selected set is also the source that is being listened to,
the whole system will be put in standby.
Note:
- It is possible to put the whole system into the standby mode
if PHONO is selected as a source, but it is not possible to
put just a record player into standby mode.
BALANCE CONTROL_
It is possible to adjust the stereo balance between the left and
right channels with BALANCE L(eft) or R(ight) on the remote
control.
• Press one of the balance keys on the remote control to
select the balance mode. The display shows the current set¬
ting.
• Press BALANCE L(eft) or R(ight) on the remote control to
adjust the stereo balance.
There are 8 positions to the left and 8 positions to the right.
The setting is changed one position every time one of the
BALANCE buttons is pressed.
• Press a source selection button to leave the balance mode.
The balance mode is left automatically when no balance
adjustments are made for 20 seconds.
This control is shown graphically on the equalizer display as
illustrated below (leftmost, middle and rightmost position)
__
4'
jT
= §§ = = = §§ = = _ ._
1*
2
<
4
<
5 <
63
160
400
IK
2-5 K 6.3 K 15 K
7<
a<
10
«
FLAT
SURROUND
PRESENCE
HALL
l]0
m
110
mi
ss
Ijk!
IW<
m
110
m
SS SS SS
stlivem
fcW
t&(
CONCERT
If'
= = = = = = == =E = == g i§
2<
i <
5
<
63
160
400
IK
2.3 K 6.3 K
16 K
7<
$<
9
<
10
«
FLAT
SURROUND
PRESENCE
HALL
S3
m
110
m
S3
m
m
m
(10
m
f!0
ii0
£0
STARLUM
fdM
kk)
liki
CONCERT
+10
0
__
==
ft
S'
Of 1/
#
— = == = ~ =§= = =
1 <
2<
4
<
5 <
63
160
400
IK
2.5 K
6.3 K
16 K
6
<
7<
8«
0 <
10
<
FLAT
SURROUND
PRESENCE
HALL
110
|W\t
110
S3
JWxl
m
m
*30
IWtf
@0
(10
i!0
STmveM
l/ki
/&<
liki
CONCERT
MULTI LANGUAGE_
You can select the following languages to display messages on
the amplifier, tuner and CD player:
- English
- Frangais
- Espahol
- Deutsch
- Portugues
- Italiano
• Press LANGUAGE 3 to change the current language.
The display shows the next language for 2 seconds.
• Press LANGUAGE 3 again until the desired language
appears on the display.
• The selected language is stored automatically when LAN¬
GUAGE 3 is not pressed for two seconds. Once chosen, the
system will remember the language.
CUSTOM GREETING_
After language selection or when you wake up the system, it
wishes you, depending on the time. Good Morning, Good
Afternoon or Good Evening in the chosen language. When no
time is available, the system greeting is Hello.
9
Advertisement
