Related Manuals for GPI L 5020
Summary of Contents for GPI L 5020
- Page 1 Product Owner’ s Manual Manual del propietario del producto Manuel du propriétaire du produit Pump Oil Transfer Pump Bomba de transferencia de aceite Pompe de transfert d’huile Models: L 5020, L 5116, L 5132...
- Page 2 à la clientèle. Nous serons heureux de vous aider. Call / Llamar / Appel: 800-835-0113 or 316-686-7361 Email: gpisales@gplains.com Website: gpi.net SAVE / GUARDAR / CONSERVEZ Model / Modelo / Modèle #: ������������������� Serial / Serie / Série #: ������������������������ Date / Fecha / Date: ��������������������������...
- Page 3 Do not use this pump for dispensing any fluids other than those for which it the warranty. • This manual covers 12 volt DC electric oil pump model L 5020, and 115 volt was designed. To do so may damage the pumps components and will void Temp_Caution1.eps Heavy_Hazard.eps...
- Page 4 Disconnect power when product is unattended or in the case of a malfunction. Disconnect power before any inspection, servicing, or maintenance. gpi.net/my-pump To prevent physical injury or property damage, observe VEA EL MANUAL DEL SEE OWNER’S MANUAL FOR DETAILS PROPIETARIO PARA DETALLES precautions against fire or explosion when dispensing fuel.
- Page 5 safety, please take a moment to review the warnings below. Observe precautions against electrical shock when operating Inspect external pump wiring regularly to make sure it is To prevent physical injury or property damage, observe the system. Serious or fatal shock can result from operating correctly connected.
-
Page 6: Specifications
230-volts if properly wired by an Electrician (see the label on the motor for specifications). GPI does not supply any wiring items or hookup connectors for the 230 voltage. Rewiring for 230-volts is the risk and responsibility of the buyer/owner and user. - Page 7 GENERAL SAFETY INFORMATION ( CONTINUED ) Do not use the GPI Oil pump with water, acids, brake fluid or windshield washer fluid. If in doubt about compatibility of a specific fluid, contact the supplier of the fluid to check for chemical compatibility with: •Aluminum...
-
Page 8: Installation Instructions
Suction pipe should extend 2 to 3 inches above bottom of tank. the pump is to be installed in a Class I, Division I location please contact GPI for the Screw suction pipe into inlet threads of pump base. -
Page 9: Electrical Installation
1 HP, 3450 RPM – 13.3/6.6 amps 12-volt DC: .40 HP, 1620 RPM – 40 amps 12-volt DC Powered Pumps (Model L 5020): This GPI Oil Pump is factory wired for 12-volt DC. Circuit must be protected with a 40 amp automotive-type fuse. -
Page 10: Operation
Excessive motor heat will trip the device and will only reset after the motor has cooled. trips. If left on, the pump will automatically reset when cool and Model L 5020: The 12-volt model is protected by an inline fuse (supplied), and NOTE: Ensure the tank contains enough fuel. -
Page 11: Maintenance
MAINTENANCE NOTE: This pump is designed for minimum maintenance. The motor bearings are self-lubricating. Inspect the pump and components regularly for fuel leaks and make sure the hose and power cord are in good condition. If damaged, replace before use. Keep the pump exterior clean to help identify leaks. IMPORTANT: Do not use this pump for water, chemicals or herbicides. -
Page 12: Troubleshooting
TROUBLESHOOTING SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION 1. Dirty strainer screen Remove and clean strainer. A. PUMP WON’T 2. Suction line problem Check for leaks in suction line. PRIME 3. Pump outlet is blocked Check pump outlet system for blockage. or valve is shutoff 4. - Page 13 TROUBLESHOOTING ( CONTINUED ) SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION 1. Fluid viscosity exceeds Refer to the Viscosity Charts for E. MOTOR viscosity limits. pumps rated capability OVERHEATS 2. Gerotor is not rotating Inspect gerotor for smooth rotation. Remove any debris. smoothly 3.
-
Page 14: Parts List
PARTS LIST... - Page 15 PARTS LIST ( CONTINUED ) Ref. Description Part Number Qty. Gerotor Housing Kit 142502-01 Gerotor Housing ▲ Spring Pins ▲ Gerotor Housing O-Ring #144 ▲ Push-On Retaining Ring ▲ 3/8” X 1” Hex Head SEMS ▲ Base Assembly Kit 142502-02 Base Assembly ▲...
- Page 16 PARTS LIST ( CONTINUED ) Ref. Description Part Number Qty. Poppet Plug Assembly 142023-01 Bypass Plug ▲ Hardened Ground Dowel Pin ▲ Poppet O-Ring #908 ▲ Bypass Spring 142005-01 Poppet Assembly 142021-01 Poppet ▲ Poppet Seal ▲ External Retaining Ring ▲...
-
Page 17: Viscosity Charts
VISCOSITY CHARTS... - Page 18 VISCOSITY CHARTS ( CONTINUED )
- Page 19 VISCOSITY CHARTS ( CONTINUED )
- Page 20 90-DAY WARRANTY applies Product components considered wear items, to the following products: i.e. vanes, etc., are NOT included within the GPI® Fluid Transfer Hand Pumps: scope of this warranty. RP-5, BP-12, LP-50 90-DAY WARRANTY applies to Spare Parts, Kits and Accessories Charges for shipping and insuring packages to Great Plains Industries, Inc.