DIGITAL PRESSURE GAUGE
PG-200
INSTRUCTION MANUAL
This caution mark describes when there is a possibility that user may suffer from damage or physical damage may occur if the product is used improperly.
WARNING
These products (pressure sensors, pressure switches, pressure gauges, pressure indicators, leakage sensors, etc.) are designed and manufactured as general industrial
parts. Therefore, a person with sufficient knowledge and experience shall confirm the conditions and environments described in the catalog, specifications, and
instruction manual of each product, check the suitability of the product for the machine, device, or system which you use, and ensure safety before use.
These products are not intended to be used for applications particularly requiring high reliability (These include, but are not limited to, nuclear power control,
aerospace and military purposes).
The details of warranty shall be as per the descriptions in this document and we shall not be liable for any damage on you resulting from the use of any equipment or
device (including control systems) which is not in accordance with this document (hereinafter referred to as "use in violation"). In the case where you resell our
products, we shall not be liable for any damage on a third party resulting from use in violation by the third party, and even if we make payment to the third party in
connection with such use in violation regardless of the name by which such payment may be called, we may demand the whole amount thereof from you.
1. Handling Note
§
CAUTION
CAUTION
⑴Mounting the attachment for panel type
If fightenig the attachment to the pressure port, the tightening torque should be around 1 N・m.
⑵Piping for stand-alone type
For piping, use the hexagonal portion of the pressure port for driving.
⑶Media to be used
The Pressure Gauge should be used for fluids that cannot corrode the diaphragm of SUS316L, pressure port of SUS 316 and O-ring of fluoro rubber.
⑷Excessive pressure
The pressure to be measured is within the specified range. Measurement of a higher pressure than the maximum allowable one may cause performance
degradation or destruction.
⑸Internal battery
①Replace battery with Toshiba Battery Co.,Ltd./ERVM3.6V/lithium battery only. Use of another battery may present a risk of fire or explosion. If you need
replace battery, please place an order with us.
②When "LOBAT" sign is displayed, the battery should be replaced.
③The battery used in this device may present risk of fire of chemical burn if mistreated. Do not recharge, disassemble, heat above 100℃(212°F), or incinerate.
④Dispose of used battery promptly. Keep away from children. Do not disassemble and do not dispose of in fire.
⑹Maintenance
If the Pressure Gauge gets dirty, wipe it off with hardly squeezed cloth containing a neutral detergent. Do not use any thinner and benzine.
⑺Protection against noises
①Noises having mixed in the switch output or power line may cause the Pressure Gauge to change the pressure indication, malfunction or be broken.
Take some measure to put the Pressure Gauge away from power line or use shielded wire. It is effective to ground the Pressure Gauge.
②If the switch output has an induction load such as relay or solenoid connected to it, it should have a surge absorber circuit put in it. The relay contacts
should have a contact preventive circuit put in it to prevent noises from being generated.
⑻Prohibition of short-circuiting the switch terminals
Do not short-circuit the switch output terminal to any power terminal. The internal circuit may be broken.
You are greatly appreciated for purchasing
NIDEC COMPONENTS CORP. Model PG−200 digital
Pressure Gauge. You should read this instruction manual
thoroughly to operate the PG−200 in optimum state.
Ver.8.0
WARNING
WARNING
This caution mark describes when there is a possibility that user may suffer from damage or physical
damage may occur if the product is used improperly.
For more detailed information please ask for the
nearest distributor or the following sales center.
Nishi-Shinjuku Prime Square bldg., 7-5-25
Nishi-Shinjuku, Shinjuku-ku,Tokyo 160-0023, Japan
Phone: +81-3-3364-7055 Fax: +81-3-3364-7098
URL : https://www.nidec-components.com
1