Yamaha MU10 Owner's Manual page 29

MIDI Data Format
The following NRPN numbers can be received.
NRPN DATA ENTRY
MSB LSB MSB PARAMETER NAME and VALUE RANGE
01H 08H mmH Vibrato Rate
mm : 00H-40H-7FH (-64 - 0 - +63)
01H 09H mmH Vibrato Depth
mm : 00H-40H-7FH (-64 - 0 - +63)
01H 0AH mmH Vibrato Delay
mm : 00H-40H-7FH (-64 - 0 - +63)
01H 20H mmH Filter Cutoff Frequency
mm : 00H-40H-7FH (-64 - 0 - +63)
01H 21H mmH Filter Resonance
mm : 00H-40H-7FH (-64 - 0 - +63)
01H 63H mmH EG Attack Time
mm : 00H-40H-7FH (-64 - 0 - +63)
01H 64H mmH EG Decay Time
mm : 00H-40H-7FH (-64 - 0 - +63)
01H 66H mmH EG Release Time
mm : 00H-40H-7FH (-64 - 0 - +63)
14H rrH mmH Drum Filter Cutoff Frequency
mm : 00H-40H-7FH (-64 - 0 - +63)
rr : drum instrument note number
15H rrH mmH Drum Filter Resonance
mm : 00H-40H-7FH (-64 - 0 - +63)
rr : drum instrument note number
16H rrH mmH Drum EG Attack Rate
mm : 00H-40H-7FH (-64 - 0 - +63)
rr : drum instrument note number
17H rrH mmH Drum EG Decay Rate
mm : 00H-40H-7FH (-64 - 0 - +63)
rr : drum instrument note number
Applies to both Decay1 and 2.
18H rrH mmH Drum Instrument Pitch Coarse
mm : 00H-40H-7FH (-64 - 0 - +63)
rr : drum instrument note number
19H rrH mmH Drum Instrument Pitch Fine
mm : 00H-40H-7FH (-64 - 0 - +63)
rr : drum instrument note number
1AH rrH mmH Drum Instrument Level
mm : 00-7F (0-max)
rr : drum instrument note number
1CH rrH mmH Drum Instrument Pan
mm : 00H-40H-7FH
rr : drum instrument note number
1DH rrH mmH Drum Instrument Reverb Send Level
mm : 00H-7FH (0-max)
rr : drum instrument note number
1EH rrH mmH Drum Instrument Chorus Send Level
mm : 00H-7FH (0-max)
rr : drum instrument note number
1FH rrH mmH Drum Instrument Variation Send Level
mm : 00H-7FH (0-max)
rr : drum instrument note number
MSB 14H-1FH (for Drum) is valid only if the Multi
Part parameter (Table 1-4) PART MODE = DRUMS 1
or DRUMS2 for that channel. (If PART MODE =
DRUM, no values will be changed.)
28
(random, left-center-right)
1.2.22 RPN (Registered Parameter Number)
Messages which offset, or add or subtract values from
a Part's pitch bend sensitivity, tuning, or other
parameter settings.
CNTRL# PARAMETER
100 RPN LSB
101 RPN MSB
* Note that once the RPN has been set for a channel,
subsequent data entry will be recognized as the same
RPN's value change. Therefore after you use the
RPN, you should set a Null (7FH, 7FH) value to
avoid an unexpected result.
The following RPN numbers can be received.
RPN DATA ENTRY
MSB LSB MSB LSB PARAMETER NAME and VALUE RANGE
00H 00H mmH -- Pitch Bend Sensitivity
mm : 00-18H (0-24 chromatic steps)
Assignable in chromatic steps up to
2 octaves
Default : 02H
LSB value is ignored.
00H 01H mmH 11H Fine Tuning
mm : 00H-40H-7FH (-64 - 0 - +63)
00H 02H mmH -- Coarse Tuning
mm : 28H-40H-58H (-24 - +24 chro-
matic steps)
LSB value is ignored.
7FH 7FH -- -- RPN null
Cancels RPN and NRPN numbers.
1.2.23 Channel Mode Messages
The following Channel Mode Messages can be received.
2nd BYTE 3rd BYTE
120 0
121 0
123 0
124 0
125 0
126 0 - 16
127 0
1.2.23.1 All Sounds Off
Terminates all sounds currently sounding on the
specified channel. However, the status of channel
messages such as Note On and Hold On is
maintained.
1.2.23.2 Reset All Controllers
The values of the following controllers will be
reset to the defaults.
CONTROLLER
Pitch Bend Change
Channel Aftertouch
Polyphonic Aftertouch
Modulation
Expression
DATA RANGE
0...127 (Default:7FH)
0...127 (Default:7FH)
MESSAGE
All Sounds Off
Reset All Controllers
All Notes Off
Omni Off
Omni On
Mono
Poly
VALUE
0 (center)
0 (off)
0 (off)
0 (off)
127 (max)