Yamaha MU10 Owner's Manual page 28

1.2.13 Release Time
Messages which adjust the envelope release time set
for each Voice.
CNTRL# PARAMETER
72 Release Time
The value set here is an offset value which will be
added to or subtracted from the Voice data.
1.2.14 Attack Time
Messages which adjust the envelope attack time set
for each Voice.
CNTRL# PARAMETER
73 Attack Time
The value set here is an offset value which will be
added to or subtracted from the Voice data.
1.2.15 Brightness
Messages which adjust the filter cutoff frequency set
for each Voice.
CNTRL# PARAMETER
74 Brightness
The value set here is an offset value which will be
added to or subtracted from the Voice data.
Lower values will result in a softer sound.
Depending on the Voice, the effective range may be
narrower than the range available for adjustment.
1.2.16 Portamento Control
Messages which apply a portamento between the
currently sounding note and the subsequent note.
CNTRL# PARAMETER
84 Portamento Control 0...127
Portamento Control is transmitted specifying the Note
On Key of the currently-sounding note.
Specify a Portamento Source Key number between 0-
127.
When a Portamento Control message is received, the
currently sounding pitch will change with a
Portamento Time of 0 to the next Key On key on the
same channel.
For example, the following settings would apply a
portamento from note C3 to C4.
90 3C 7F ........... C3 = Key On
B0 54 3C ........... Source Key number set to C3
90 48 7F ........... C4 = Key On (When C4 = on, C3
is raised by a portamento to C4.)
Even if the Multi Part parameter Rcv PORTAMENTO
(Table 1-4) = OFF, the Portamento Control message
will be received.
DATA RANGE
0...127 (0 : -64, 64 : +0,
127 : +63)
DATA RANGE
0...127 (0 : -64, 64 : +0,
127 : +63)
DATA RANGE
0...127 (0 : -64, 64 : +0,
127 : +63)
DATA RANGE
MIDI Data Format
1.2.17 Effect1 Depth (Reverb Send Level)
Messages which adjust the send level for the Reverb
effect.
CNTRL# PARAMETER
91 Effect1 Depth
1.2.18 Effect3 Depth (Chorus Send Level)
Messages which adjust the send level for the Chorus
effect.
CNTRL# PARAMETER
93 Effect3 Depth
1.2.19 Effect4 Depth (Variation Effect Send Level)
Messages which adjust the send level for the Variation
effect.
CNTRL# PARAMETER
94 Effect4 Depth
If Variation Connection (Table 1-3) = 1 (System), this
message sets the send level for the Variation effect.
If Variation Connection = 0 (Insertion), this has no
effect.
1.2.20 Data Increment / Decrement (for RPN)
Messages which increase or decrease the MSB value
of Pitch Bend Sensitivity, Fine Tune, or Coarse Tune
in steps of 1.
CNTRL# PARAMETER
96 RPN Increment
97 RPN Decrement
The data byte is ignored.
When the maximum value or minimum value is
reached, the value will not be incremented or
decremented further.
(Incrementing the Fine Tune will not cause the Coarse
Tune to be incremented.)
1.2.21 NRPN (Non-Registered Parameter Number)
Messages which adjust a Voice's vibrato, filter, EG,
drum setup or other parameter settings.
CNTRL# PARAMETER
98 NRPN LSB
99 NRPN MSB
First send the NRPN MSB and NRPN LSB to specify
the parameter which is to be controlled. Then use
Data Entry to set the value of the specified parameter.
* Note that once the NRPN has been set for a channel,
subsequent data entry will be recognized as the same
NRPN's value change. Therefore, after you use the
NRPN, you should set a Null (7FH, 7FH) value to
avoid an unexpected result.
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
0...127
DATA RANGE
0...127
0...127
27