Table of Contents
Advertisement
P U S H B U T T O N I G N I T I O N S Y S T E M C O N N E C T I O N D I A G R A M S - U P T O 3 0 0 K
B T U S Y S T E M S
1. To place the Spark Igniter in the
proper position, installer will need
to drill a hole in the plate.
Measure where to drill hole by
Spark
holding tip of Spark Igniter no further
Igniter
Stem
than .125" away from inside edge
of jet. Drill hole where base of spark
igniter sits. Thread wires through
drilled hole and pull until Spark
Drill
Igniter bracket is in place on plate.
Here
Screw Spark Igniter to plate.
If the distance to the jet is greater than .125", you can adjust the position by gently bending the spark ignitor by the stem.
Bending too far can result in breakage. Do not flex at the existing bend, this can result in breakage. If the spark ignitor is too
far away or too close to the jet, you will not get a strong enough spark to light the burner.
2. Install Push Button Module
into Mounting Bracket
Unscrew Button Cover.
Remove plastic Nut.
Push Button
Insert Push Button Stem through
Module
mounting bracket hole.
Put on plastic Nut and turn until
Push Button Control has been
secured to mounting bracket.
Insert AA Battery into Button Stem.
Screw on Button Cover.
3. Connect Spark Igniter Wires
Crimp Spark Igniter Wires,
then slide crimped wires on
Spark Igniter
Wires
to connections using needle
nose pliers. Be careful not to
break connectors. Wires can
go in either connection.
4. Test without Gas
Test Spark Igniter and Push
Push Button
Module
Button Module WITHOUT gas,
making sure spark arcs from
electricity to jet.
5. Test with Gas
Burner should light within 5
seconds or a few clicks.
24
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
Warming_Trends_Instruction_Manual_V3.8.indd 24-25
Warming_Trends_Instruction_Manual_V3.8.indd 24-25
.125"
Jet
CROSSFIRE
Brass Burner
Plate
Key Valve
Button Stem
Mounting Bracket
Nut
AA Battery
Button Cover
Key Valve
Mounting Bracket
M E R C U R Y I G N I T I O N : I N S T A L L A T I O N I N S T R U C T I O N S
If the Pilot Assembly for the Mercury Ignition is not installed on the Plate or Pan, start here for complete installation
instructions. If the Pilot Assembly has been installed on the plate or pan, skip to step 3 below for
installation instructions.
INSTALLATION OF THE MERCURY IGNITION PILOT ASSEMBLY TO THE PLATE USING PRE-CUT KNOCKOUTS
The Warming Trends plate/pan that was included with your Order should have pre-cut pilot assembly knockouts for
various burners. The burner type and size are etched into the plate/pan next to the knockout for that burner's pilot
assembly location.
1. LOCATE AND REMOVE THE APPROPRIATE KNOCKOUT
1.1 Confirm the type and size of your burner on the Packing Slip for your Order.
1.2 Locate the Pilot Assembly knockout on the plate/pan that matches your burner type and size. {See Photo 1}.
1.3 Remove the matching knockout by placing a screwdriver or other small tool in the opening at the edge of the
knockout. Push one side of the knockout down to break the connector and remove the circular piece of aluminum
with pliers. Do not remove any other knockouts. {See Photo 2}.
Photo 1: Pilot Assembly Knockouts
2. INSTALLING THE PILOT ASSEMBLY ON THE PLATE/PAN
2.1 Locate the Pilot Assembly. This includes the Pilot Hood, the Electrode and Thermocouple. {See Photo 3a and
3b}.
Pilot
Self Tapping Screws
Square Cap
Photo 3a: Full Pilot Assembly
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
Photo 2: Breaking the Knockouts
Electrode
Thermocouple
Pilot Head
Photo 3b: Top-Down View of Pilot Assembly
25
2/20/2024 10:45:22 AM
2/20/2024 10:45:22 AM
Advertisement
Table of Contents
