Ukca Declaration Of Conformity - Emerson Hytork XL Series Safety Manual

Appendix
March 2024
Appendix B:
This declaration of conformity is issued under the sole responsibility of the manufacturer. The products
specified below meet the basic health and safety requirements of the below mentioned UK legislations.
Product Description:
• Hytork™ XL-Series Pneumatic actuator
• Double-acting and spring-return actuators
• Sizes: XL26, XL71, XL131, XL186, XL221, XL281,
XL426, XL681, XL1127, XL1372, XL2586 and XL4581
Product Variations:
• Product variations of the above mentioned types
are still covered by the listed regulations and are
UKCA marked.
UK Declaration of Conformity
Issued in accordance with the:
UK Regulation 2016 – UK SI 2016 No. 1105
• For Gas Group 2, (see Safety Guide, DOC.SG.HX.1,
Section 3.2.1, Operating Media). Hytork-XL Series
pneumatic actuators are excluded from the
requirements of the Pressure Equipment (Safety)
Regulations 2016, UK Statutory Instrument 2016
No. 1105, as amended by the Product Safety
and Metrology etc. (Amendment etc.) (EU Exit)
Regulations 2019, UK Statutory Instrument 2019
No. 696 based on SCHEDULE 1, Paragraph 1(f) of
the regulation.
• For Gas Group 1 pressure media, first consult
engineering to check compatibility of pressure
media with the actuator.
• The below listed limited range of
Hytork-XL Series actuator sizes are rated
"Sound-Engineering-Practice" or Module A
(Internal Production Control) and are available on
request for use with Gas Group 1 media.
• Double-acting and spring-return actuators
• Sizes: XL26, XL71, XL131, XL186, XL221, XL281,
XL426, XL681, XL1127 and XL1372
UK Declaration of Conformity
Issued in accordance with the:
UK Regulation 2016 – UK SI 2016 No. 1107
Marking of the Product:
• II 2G Ex h IIC TX Gb
II 2D Ex h IIIC TX Db
• For maximum temperature limits and classifications,
see Safety Guide: DOC.SG.HX.1, Section 5, Safety
Instructions for Use in (Potential)
Explosive Atmosphere.
Applicable Standards:
• BS EN IEC 60079-0:2018
BS EN ISO 80079-37:2016 BS EN 1127-1:2019
16

UKCA Declaration of Conformity

Legal representative entity for the GB Market:
Emerson Process Management Limited, Company No. 00671801,
Meridian East, Leicester LE19 1UX, United Kingdom
Regulatory Compliance Department
Email: ukproductcompliance@emerson.com
Phone: +44 11 6282 23 64
BS EN ISO 80079-36:2016
Serial Number:
• Each actuator has an identifiable serial number.
Manufacturer:
• Emerson Process Management
Valve Automation (M) Sdn. Bhd.
Lot 13112, Mukim Labu,
Kawasan Perindustrian Nilai,
71807 Nilai, Negeri Sembilan
Malaysia
Declaration of Incorporation of
Partly Completed Machinery
Issued in accordance with the:
UK Regulation 2008 – UK SI 2008 No. 1597
SCHEDULE 2, Annex II(B)
Essential requirements applied and complied with:
• 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.4, 1.3.7, 1.5.2, 1.5.3,
1.5.4, 1.5.7, 1.6.1, 1.7.1, 1.7.3 and 1.7.4.
• Technical documentation is drafted in compliance
with Annex VII, Section B of the Regulation.
• Before the actuator is put into operation, the
machine into or onto which the actuator will be
installed, must comply with the stipulations of the
machinery directive.
• The relevant information concerning the machine
or part will be available in the event of a motivated
request from national authorities.
Applicable Standards:
• BS EN ISO 12100:2010
Signed: _____________________________
Name: Bharat Shirolikar
Position: Director, Global
Product Engineering
Date: 2023-11-01
Place: Houston TX, U.S.A.
Safety Guide
DOC.SG.HX.1 Rev. 2
VCCAQ-17151-EN
Rev. 1
Appendix