Related Manuals for Husqvarna AUTOMOWER 310E NERA
Summary of Contents for Husqvarna AUTOMOWER 310E NERA
- Page 1 Operator's manual ® HUSQVARNA AUTOMOWER 310E NERA/410XE NERA EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.
-
Page 2: Table Of Contents
Contents 5.6 To charge the battery.......... 26 1 Safety 6 Maintenance 1.1 Safety definitions...........3 1.2 General safety instructions........3 6.1 Introduction - maintenance........27 1.3 Safety instructions for installation......4 6.2 Maintenance schedule........27 1.4 Safety instructions for operation......4 6.3 Clean the product..........28 1.5 Safety instructions for maintenance...... -
Page 3: Safety
• If there is a risk of thunderstorm, Husqvarna or mental capabilities or lack of experience and recommends that the power supply and all the knowledge, if they have been given supervision... -
Page 4: Safety Instructions For Installation
To set the product to OFF with its special characteristics and safety work area. Refer to on page 25 . Husqvarna recommends to set the regulations. product to operate when the work area has no •... -
Page 5: To Lift And Move The Product
of electrical/mechanical abuse. Avoid storage in direct sunlight. 1.7 To lift and move the product WARNING: The product must be set to OFF before you lift the product. The product is disabled when the indicator on the jog wheel goes off. CAUTION: Do not lift the product when it is parked in the charging station. -
Page 6: Introduction
The serial number and the product number are on the product rating plate and on the product carton. • Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchase to register your product. -
Page 7: Product Overview
2.4 Product overview Automower® 310E Automower® 410XE NERA NERA Rating plate Display Top cover START button Front wheels 10. Jog wheel Product body 11. STOP button Accessory hub 12. Blade disc guard Radar 13. Rear wheels Headlights 14. Skid plate Found below the top cover. -
Page 8: Symbols On The Product
15. Chassis with electronics, battery and motors WARNING: Read the opera- 16. EdgeCut blade disc tor instructions before you op- 17. Main blade disc erate the product. 18. Handle 19. Contact plates WARNING: Disable the prod- 20. LED indicator of the charging station uct before maintenance or 21. -
Page 9: Symbols On The Battery
• The display (A) shows the status bar and the main Symbols on the display on menu symbols. Refer to page 9 . Do not make modifications on the low- voltage cable. • The START button (B) is used to start the operation of product. - Page 10 Battery level. ® 2.8.2 Menu structure overview in Automower Access ® 2.8.2.1 Symbols in the main menu for Automower Access Mow menu you can set the product In the Cutting height to cut to the set schedule or in secondary area mode.
- Page 11 Language Language menu you can select a In the language in the display. Power off Power off sets the product to OFF. ® 2.8.2.2 Symbols in the submenu for Automower Access Cutting height Cutting height submenu you can In the select a cutting height for the product.
-
Page 12: Installation With Wire
Wi-Fi coverage in the work area if you Note: ® use the Automower Connect app remotely. Refer Refer to www.husqvarna.com for more To install the Automower ® Connect app on information about installation. page 16 . For Automower ®... - Page 13 • Keep a minimum of 150 cm / 60 in. of free space • Use a residual-current device (RCD) with a tripping to the right and left of the center of the charging current of maximum 30 mA when you connect the station.
- Page 14 • For slopes adjacent to a public road, put a barrier of minimum 15 cm / 6 in. along the outer edge of the slope. You can use a wall or a fence as a barrier. 3.4.3.2 Passages A passage is a section that has boundary wire on each side and that connects 2 parts of the work area.
- Page 15 Some obstacles are resistant to a collision, for example, Note: The boundary wire must be put as 1 loop trees or bushes that are more than 15 cm / 5.9 in. in around all of the work area (A + B). height.
-
Page 16: Installation Of The Product
® jog wheel to select Bluetooth to enable it again. Enter the factory PIN code 1234 on the product. Log on to your Husqvarna account in the ® Automower Connect app. ®... - Page 17 Note: The product can be put in the charging station to charge while you install the boundary wire. 12. Put the low-voltage cable in the ground with stakes or bury the cable. Refer to To put the wire into position with stakes on page 18 or To bury the boundary wire or the guide wire on page 18 .
- Page 18 3.5.6 To install the guide wire Note: Make sure that you can see the ends of the wires through the transparent area of CAUTION: Twinned cables, or a the coupler. screw terminal block that is insulated with insulation tape are not satisfactory splices. Push down the cover on the coupler with Soil moisture will cause the wire to oxidize adjustable pliers to attach the wires in the...
- Page 19 3.5.9 To do a visual check of the charging station Make sure that the indicator LED lamp on the charging station has a green light. If the indicator LED lamp does not have a green light, do a check of the installation. Refer to indicator of the charging station for boundary wire installation on page 37 and To install the charging station on page 16 .
-
Page 20: Settings
4 Settings 4.2.1 Adjust the cutting height This chapter gives information about the settings for ® the product that you can make in the Automower The cutting height can be adjusted from 2 cm / 0.8 in. to Connect app. All setting for the product are available in 5.5 cm / 2.2 in. -
Page 21: Installation
You can set the charging station signal min , avg or max . 4.3.4.1 To enable the loop signal Note: Husqvarna recommends to set the charging Set the product to ON. max . It is usually better to move the station signal to Put the product in the charging station. -
Page 22: Accessories
Test 4.4.1.2 Follow guide wire and boundary wire Each area can be enabled or disabled. Use the function to measure the distance from the charging The time interval can be set for when the product starts station to where the product must start to cut. Refer to to follow the boundary wire and guide wire to find the To measure the distance from the charging station on charging station. -
Page 23: General
4.5.1 Headlights 4.7.1 New loop signal ® Headlights is only available for Automower 410XE The loop signal is randomly selected to create a unique NERA. link between the product and the charging station. In rare cases, there may be a need to generate a new There are 4 different headlight settings that control when signal, for instance if 2 adjacent installations have a very the headlights are on:... -
Page 24: Messages
product to a Wi-Fi network. You can also see the signal The data collection for the AIM map starts automatically. strength and connectivity status. The product collects data while it operates and the map is completed in 1-2 weeks. Remove temporary This menu is only available when your mobile device is obstacles on the lawn when the product operates and ®... -
Page 25: Operation
5 Operation The most frequently used operation settings are Note: If you will cut the main area after the battery is ® included in the Automower Access, refer to Main area mode before you charged, set the product to ® Automower Access on page 6 . -
Page 26: To Charge The Battery
Push the jog wheel for 3 seconds to set the product to OFF. You can also use the jog wheel Power off in the menu in the display. to select Make sure that the LED indicator on the jog wheel is not lit. -
Page 27: Maintenance
6 Maintenance 6.1 Introduction - maintenance It is important that the blade disc rotates easily and that the edges of the blades are not damaged. The usual lifetime of the blades are 3-6 weeks for the main WARNING: Set the product to OFF blade disc and 9-12 weeks for the EdgeCut blade disc. -
Page 28: Clean The Product
Set the product to OFF. with a brush or running water from a water hose. Carefully pull the top cover at the rear. Husqvarna recommends to use a special cleaning and maintenance kit. Speak to your Husqvarna servicing dealer for more information. -
Page 29: Battery
6.3.3 To clean the wheels The product does not operate satisfactorily in slopes if the wheels are blocked with grass. • Use a soft brush to clean the wheels. • If it is necessary, remove the wheel cover with a flat screwdriver. -
Page 30: Replacement Of The Blades
6.5 Replacement of the blades WARNING: Husqvarna can only guarantee safety if you use Husqvarna original blades with the embossed crowned H-mark logotype. WARNING: You must replace the screws when you replace the blades. The used screws can wear quickly and make the blade come loose, this can cause serious injury. -
Page 31: Troubleshooting
® ® The messages in the table below are shown in Automower Connect and Automower Access. Speak to your Husqvarna representative if the same message shows frequently. Message Cause Action Wrong PIN code An incorrect PIN code has been entered. 5 Enter the correct PIN code. - Page 32 Message Cause Action No loop signal There is no power in the charging station. Examine if the power supply unit or the low- The LED indicator on the charging station is voltage cable is damaged or not installed not on. correctly to the power outlet or the charging station.
- Page 33 Message Cause Action Lifted The lift sensor has been enabled because Make sure that the body of the product body the product has been lifted. can move freely around its chassis. Remove or make an island around objects that can cause the body to be lifted.
- Page 34 Message Cause Action Electronic problem Temporary electronic or firmware problem in Restart the product. the product. Loop sensor problem If the problem stays, speak to your approved servicing dealer. Tilt sensor problem Invalid sub-device combination STOP button prob- Connectivity problem Safety function faulty Invalid system config- uration...
- Page 35 Message Cause Action Temperature restric- The product does not operate if the battery The product starts to operate again when the tion temperature is too high or too low. temperature is between the set limits and the schedule settings let the product to operate. Make sure that the charging station is put in an area with protection from the sun.
- Page 36 Message Cause Action EPOS plug-in not The EPOS Plug-in has been installed earlier, Make sure that the EPOS Plug-in is installed found but cannot be found. correctly and that the cable is connected. Re- start the product. If the problem stays, speak to your authorized service center.
-
Page 37: Led Indicator Of The Charging Station For Boundary Wire Installation
The LED indicator of the charging station is green when the installation is correct. If the LED indicator of the charging station is not green, follow the troubleshooting table below. Speak to your local Husqvarna representative or go to www.husqvarna.com for more information. LED indicator... -
Page 38: Symptoms
7.3 Symptoms If the product does not operate as usual, follow the symptoms table below. Speak to your Husqvarna customer service if you cannot find the cause for the fault. Symptoms Cause Action Edges of the lawn The blade disc guard for the EdgeCut blade... -
Page 39: Finding Breaks In The Loop Wire
Symptoms Cause Action Schedule on page 20 . The product is The product has operated the maximum cut- No action. Refer to parked for hours in ting time for the day. the charging station. The hatch is closed but the START button is Push the STOP button to open the hatch. - Page 40 LED indicator of the the boundary loop. Refer to green light and a flashing blue light. Then follow charging station for boundary wire installation on instruction in step 5 below. page 37 . If indicator lamp still flashes blue in step 3 above: Put AL and G1 back in their original Check that the boundary wire connections to the positions.
-
Page 41: Transportation, Storage And Disposal
We recommend to put the product in the package of the product or put the product with all wheels on level ground. You can also hang the product on a Husqvarna wall hanger. Speak to your Husqvarna representative for more information about available Close the hatch. -
Page 42: Disposal
Lift and tilt the top of the charging station. Remove the warranty seal and lift up the lower chassis. Put the grommet with the cables into position. Disconnect the 2 cables (A) and (B) from the Connect the cable to the charging station. battery. -
Page 43: Technical Data
9 Technical data 9.1 Technical data ® ® Dimensions Automower 310E NERA Automower 410XE NERA Length, cm/in. 68/26.8 68/26.8 Width, cm/in. 44/17.2 44/17.2 Height, cm/in. 28/11.0 28/11.0 Weight, kg/lb 12.2 / 27 12.1 / 27 ® ® Electrical system Automower 310E NERA Automower 410XE... - Page 44 ® ® Sound data Automower 310E NERA Automower 410XE NERA Sound level, perceived, dB (A) Measured sound power noise level, dB (A) Noise emissions uncertainties, KWA dB (A) Sound pressure noise level at the operator’s ear , dB (A) ® ®...
- Page 45 Operating frequency band, MHz 2402-2480 Maximum transmitted power, dBm Husqvarna AB does not guarantee full compatibility between the product and other types of wireless systems such as remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar. 9.1.1 Registered trademarks ®...
- Page 46 46 - Technical data 2369 - 001 - 05.02.2024...
- Page 47 2369 - 001 - 05.02.2024 Technical data - 47...
- Page 48 ® AUTOMOWER is a trademark owned by Husqvarna AB. © Copyright 2024 HUSQVARNA. All rights reserved. www.husqvarna.com Original instructions 1143605-26 2024-02-16...