Table of Contents
Advertisement
Quick Links
Product overview
Fig. 1: Schematic illustration of PL50-*-SF
1
Diffuser face with 1, 2, 3 or 4 slots
2
Adjustable air control element
3
Screw fixing
4
End plate
5
End angle
6
Neck
Optional equipment: 4, 5, 10, 11
Installation manual
Air Diffusers
Slot Diffusers PURELINE50
Air Diffusers Slot Diffusers PURELINE50
GB/en
7
Plenum box
8
Suspension lug
9
Spigot
10
Lip seal
11
Damper unit for volume flow rate balancing
TROX GmbH
Heinrich-Trox-Platz
47504 Neukirchen-Vluyn
Germany
Phone: +49 (0) 2845 2020
Fax: +49 (0) 2845 202265
E-mail: trox@trox.de
http://www.troxtechnik.com
1
Advertisement
Table of Contents
Related Manuals for Trox Technik PURELINE50
Summary of Contents for Trox Technik PURELINE50
- Page 1 Diffuser face with 1, 2, 3 or 4 slots Plenum box Adjustable air control element Suspension lug Screw fixing Spigot End plate Lip seal End angle Damper unit for volume flow rate balancing Neck Optional equipment: 4, 5, 10, 11 Air Diffusers Slot Diffusers PURELINE50...
-
Page 2: Important Notes
Air terminal devices are used for the ventilation of internal spaces in industrial and comfort areas. The air terminal devices are connected to a supply air or extract air system (by others), which is typically connected to an air handling unit. Air Diffusers Slot Diffusers PURELINE50... -
Page 3: Transport And Storage
Properly dispose of packaging material. certain position. Changing this factory setting increases the commissioning time and cost. Be careful when you unpack and install the air con- trol blades on site so as not to accidentally change their position. Air Diffusers Slot Diffusers PURELINE50... - Page 4 Installation in panelled ceilings Fig. 4: Slot diffuser without extended border Length of installation opening with end plate: L1 + 9 mm Air Diffusers Slot Diffusers PURELINE50...
-
Page 5: Duct Connection
Variants with a lip seal allow for a sufficiently tight someone to give you a hand or use a lift during connection; additional sealing is not required. assembly. Fig. 5: Plenum box suspension Fix any suspension elements, e.g., threaded rods, to the ceiling. Air Diffusers Slot Diffusers PURELINE50... - Page 6 The corner section is fixed into place on site. The corner section is positioned on the front rail with the enclosed connectors (2 pieces per corner section). Fix the connectors into place on one side, then push them halfway into the front rail. Air Diffusers Slot Diffusers PURELINE50...
- Page 7 The end pieces must be fitted by others. For this purpose, the end plates or end angles must be fixed with screws. Ä (Fig. 9/1) and (Fig. 10/1) Air Diffusers Slot Diffusers PURELINE50...
- Page 8 4. Using the screws, insert the diffuser face into the mounting points provided on the cross bar on the plenum box. Using an Allen key (SW4) simplifies the fixing procedure. To remove the diffuser face, first remove the Allen screws (SW4 Allen key). Air Diffusers Slot Diffusers PURELINE50...
- Page 9 Assembly Arrangement of the fixing points in the cross bar Fig. 12: Assignment of the cross bar for fastening the front rail Cross bar clamp Cross bar Air Diffusers Slot Diffusers PURELINE50...
- Page 10 ) + 45 Fig. 15: Front rail longer than plenum box, position of plenum box centre, X = (L – L ) / 2 + 45 Fig. 16: Front rail length = plenum box length Air Diffusers Slot Diffusers PURELINE50...
- Page 11 -DF. Fig. 17: Position of the spring, ceiling thickness up to 9 mm Fig. 18: Position of the spring, ceiling thickness greater than 9 mm Variant PL50-1-*-DF PL50-2-*-DF PL50-3-*-DF PL50-4-*-DF Air Diffusers Slot Diffusers PURELINE50...
- Page 12 < 1500 mm Self-drilling screw Ø3.5 - 4.5, max. length 10 mm (provided by others) Fig. 20: 3 fixing points from L ≥ 1500 mm [mm] B [mm] 600 - 1350 – 1500 1650 1800 1950 Air Diffusers Slot Diffusers PURELINE50...
-
Page 13: Technical Data
Fig. 21: Dimensions and spigot arrangement, * spigot arrangement for plenum box variant VS Fig. 22: Plenum box variants PL50-*-HS (symmetric position of plenum box, side entry spigot) PL50-*-HA (asymmetric position of plenum box, side entry spigot) PL50-*-VS (symmetric position of plenum box, top entry spigot) Air Diffusers Slot Diffusers PURELINE50... - Page 14 Total weight [kg] = weight of front rail + weight of plenum box Enter lengths in [m] PL50-1 152 + Y PL50-2 172 + Y PL50-3 197 + Y PL50-4 229 + Y Neck extension Y = 22 / 47 / 72 / 97 / 121 Air Diffusers Slot Diffusers PURELINE50...
- Page 15 Technical data Front rails Fig. 23: PL50-2 Fig. 24: PL50-2/B00 Fig. 25: PL50-2-DF/.../B00 Variant M [mm] P [mm] Variant M [mm] P [mm] PL50-3 PL50-1 PL50-4 PL50-2 Air Diffusers Slot Diffusers PURELINE50...
- Page 16 Setting of the air control elements Alternating horizontal air discharge Alternating air control elements set to left-hand or right-hand air discharge Alternating angled air discharge Alternating air control elements set to left-hand or right-hand air discharge Vertical air discharge Air Diffusers Slot Diffusers PURELINE50...
-
Page 17: Initial Commissioning
Ensure that the devices have been correctly fixed and connected to the ducting. For commissioning see also VDI 6022, part 1 – 'Hygiene requirements for ventilation and air-condi- tioning systems and units'. Air Diffusers Slot Diffusers PURELINE50... - Page 18 When pulling the cords: White cord - Open the damper unit Green cord - Close the damper unit Fig. 26: Setting the damper unit in case of a hori- zontal spigot, e.g., with a screwdriver Air Diffusers Slot Diffusers PURELINE50...
-
Page 19: Maintenance And Cleaning
Do not use cleaning agents that contain chlorine. Do not use equipment for removing stub- born contamination, e.g. scrubbing sponges or scouring cream, as it may damage the sur- faces. Air Diffusers Slot Diffusers PURELINE50...
Need help?
Do you have a question about the PURELINE50 and is the answer not in the manual?
Questions and answers