Impedance Selector Switch - Yamaha RX-V3300 Owner's Manual

SPEAKER SETUP
I IMPEDANCE SELECTOR switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
Select the upper or lower position according to the impedance of the speakers in your system. Be sure to move this
switch only when this unit is in the standby mode.

IMPEDANCE SELECTOR switch

IMPEDANCE SELECTOR
SET BEFORE POWER ON
SELECTEUR D'INPEDANCE
ZONE 2 OUT : 8ΩMIN./SPEAKER
FRONT : 8ΩMIN./SPEAKER
REAR : 8ΩMIN./SPEAKER
:
CENTER 8ΩMIN./SPEAKER
:
REAR CENTER 8ΩMIN./SPEAKER
:
MAIN A OR B 8ΩMIN./SPEAKER
+
L
+
L
AC IN
AC OUTLETS
FRONT
EFFECT
+
L
REAR
(SURROUND)
+
CENTER
IMPEDANCE SELECTOR
SET BEFORE POWER ON ZONE 2 OUT : 6ΩMIN./SPEAKER
6ΩMIN./SPEAKER
SELECTEUR D'INPEDANCE FRONT :
REAR : 4ΩMIN./SPEAKER
CENTER : 4ΩMIN./SPEAKER
ZONE 2 OUT : 8ΩMIN./SPEAKER
REAR CENTER : 4ΩMIN./SPEAKER
+ :
L FRONT 8ΩMIN./SPEAKER
MAIN A OR B : 4ΩMIN./SPEAKER
:
REAR 8ΩMIN./SPEAKER
A + B 8ΩMIN./SPEAKER :
CENTER : 8ΩMIN./SPEAKER
REAR CENTER : 8ΩMIN./SPEAKER
B
MAIN A OR B : 8ΩMIN./SPEAKER
MAIN
+
L
A
(U.S.A. model)
14
6ΩMIN./SPEAKER
ZONE 2 OUT :
FRONT : 6ΩMIN./SPEAKER
REAR : 4ΩMIN./SPEAKER
CENTER : 4ΩMIN./SPEAKER
4ΩMIN./SPEAKER
REAR CENTER :
4ΩMIN./SPEAKER
MAIN A OR B :
A + B 8ΩMIN./SPEAKER :
Switch Speaker
position
Zone 2
Upper
Zone 2
Lower
The impedance of each speaker must be 6 Ω or higher.
The impedance of each speaker must be 6 Ω or higher.
Front
Effect
The impedance of each speaker must be 4 Ω or higher.
Rear [Australia model]
The impedance of each speaker must be 6 Ω or higher.
The impedance must be 4 Ω or higher.
Center
The impedance must be 4 Ω or higher.
Rear
[Australia model]
Center
The impedance must be 6 Ω or higher.
If you use one set of main speakers, the impedance of
each speaker must be 4 Ω or higher.
Main
If you use two sets of main speakers, the impedance of
each speaker must be 8 Ω or higher.
The impedance of each speaker must be 8 Ω or higher.
The impedance of each speaker must be 8 Ω or higher.
Front
Effect
The impedance of each speaker must be 8 Ω or higher.
Rear
The impedance must be 8 Ω or higher.
Center
The impedance must be 8 Ω or higher.
Rear
Center
If you use one set of main speakers, the impedance of
each speaker must be 8 Ω or higher.
If you use two sets of main speakers, the impedance of
Main
each speaker must be 16 Ω or higher.
[U.S.A. model]
The impedance of each speaker must be 8 Ω or higher.
Impedance level