Yamaha RX-V2600 Owner's Manual page 86

SYSTEM OPTIONS
■ Audio Select (Audio selection)
This unit comes with a variety of input jacks. You can
select the type of input signal you want to use.
Input Select > input source (DVD, etc.) > Audio Select >
Choices: Auto, HDMI, Coax/Opt, Analog
I/O Assignment
Audio Select
Decoder Mode
Volume Trim
• Select "Auto" if you want signals to be input to this
unit in the following order: HDMI signals, digital
*
signals and analog signals.
• Select "HDMI" if you only want HDMI signals to be
input to this unit. If no HDMI signals are input, no
sound is output.
• Select "Coax/Opt" if you want digital signals to be
input to this unit at the OPTICAL or COAXIAL jacks.
Use if HDMI signals are also being input.
• Select "Analog" if you only want analog signals to be
input to this unit. If no analog signals are input, no
sound is output.
*
If this unit detects a Dolby Digital or DTS signal, the
decoder automatically switches to the appropriate sound
field program.
y
• You can adjust the default input mode this unit selects when the
power is turned on (see page 98).
• DTS mode is recommended for playback of a CD or LD
encoded in DTS.
Notes
• If the digital output data of the player has been processed in any
way, you may not be able to perform DTS decoding even if you
make a digital connection between this unit and the player.
• The parameter setting for Decoder Mode takes priority over the
one for Audio Select. As a result, if Decoder Mode is set to a
setting other than Auto and Audio Select to Analog, there will
be no audio output. To resume audio output, set Decoder Mode
to Auto or set Audio Select to a setting other than Analog.
■ Decoder Mode (Decoder mode)
Use this feature to switch the input mode. You can
designate the reassigned digital input jacks (see page 81)
for specific audio signals (DTS, etc.).
Input Select > input source (DVD, etc.) >
Decoder Mode >Choices: Auto, DTS
I/O Assignment
Audio Select
Decoder Mode
Volume Trim
Rename
82
Auto
HDMI
Coax/Opt
Auto
DTS
• Select "Auto" if you want this unit to automatically
detect input signal types and select the appropriate
input mode.
• Select "DTS" if you want this unit to select DTS as the
input mode.
• The parameter setting for Decoder Mode takes priority
over the one for Audio Select. As a result, if Decoder
Mode is set to a setting other than Auto and Audio
Select to Analog, there will be no audio output. To
resume audio output, set Decoder Mode to Auto or set
Audio Select to a setting other than Analog.
■ Multi CH Assign
(Multi channel assignment)
Use this feature to set the direction of the signals input
into the center, subwoofer and surround channels when a
source component is connected to the MULTI CH INPUT
jacks. If you are inputting 8-channel signals from an
external decoder, use this feature to select jacks for the
additional front signals.
Input Select > MULTI CH > Multi CH Assign >
Volume Trim
Multi CH Assign
Input Channels (Input channels)
This setting is used to select the number of channels input
from an external decoder.
Choices: 6ch, 8ch
Note
If Zone2 Amplifier (page 96) is set to "Internal", no sound is
output from the surround back speakers even if you select "8ch".
In this case, select "6ch" and set the output setting of the external
component to 6 channels.
Front Input (Front input)
If you selected "8ch" in Input Channels, you can select
analog jacks at which front signals from an external
decoder will be input.
Choices: DVD, DTV, CBL/SAT, VCR1, DVR/VCR2,
V-AUX, CD, CD-R, MD/TAPE
Input Channels
Front Input