Siemens SIMATIC NET RUGGEDCOM RX1510 Equipment Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Industrial Equipment
  5. SIMATIC NET RUGGEDCOM RX1510
  6. Equipment manual
Siemens SIMATIC NET RUGGEDCOM RX1510 Equipment Manual

Siemens SIMATIC NET RUGGEDCOM RX1510 Equipment Manual

Rugged multi service platforms
Hide thumbs Also See for SIMATIC NET RUGGEDCOM RX1510:
Table of Contents

Advertisement

Quick Links

Download this manual
Edition
10/2023
Equipment Manual
SIMATIC NET
Rugged multi service platforms
RUGGEDCOM RX1510
https://www.siemens.com/ruggedcom

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIMATIC NET RUGGEDCOM RX1510

Summary of Contents for Siemens SIMATIC NET RUGGEDCOM RX1510

  • Page 1 Edition 10/2023 Equipment Manual SIMATIC NET Rugged multi service platforms RUGGEDCOM RX1510 https://www.siemens.com/ruggedcom...
  • Page 2 Preface Introduction Installing the Device SIMATIC NET Device Management Rugged multi service platforms RUGGEDCOM RX1510 Modules Technical Specifications Equipment Manual Certification 10/2023 C79000-G8976-1055-25...
  • Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.

  • Page 4: Table Of Contents

    SIMATIC NET glossary ......................vi Registered trademarks ......................vi Warranty ..........................vii Training ..........................vii Customer support ......................... viii Contacting Siemens ......................viii Introduction ........................... 1 Feature Highlights ....................1 Description ......................2 Required Tools and Materials ................. 3 Decommissioning and disposal ................3 Cabling Recommendations ..................
  • Page 5 Table of contents Installing/Removing Power Modules ..............30 Technical Specifications ...................... 35 General specifications ..................35 Chassis Specifications ..................35 Power Supply Specifications ................35 Failsafe Relay Specifications ................36 Operating Environment ..................36 Mechanical Specifications ..................36 Dimension Drawings ................... 36 Certification .........................

  • Page 6: Preface

    Siemens' products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customer's exposure to cyber threats.

  • Page 7: Supplementary Documentation

    SIMATIC NET glossary The SIMATIC NET glossary describes special terms that may be used in this document. The glossary is available online via Siemens Industry Online Support (SIOS) at: https://support.industry.siemens.com/cs/ww/en/view/50305045 Registered trademarks The following and possibly other names not identified by the registered trademark sign ®...

  • Page 8: Warranty

    Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void.

  • Page 9: Customer Support

    Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit https://w3.siemens.com/aspa_app/?lang=en. Mobile app Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to: •...

  • Page 10: Introduction

    Introduction The RUGGEDCOM RX1510 is a cost-efficient, rugged Layer 3 switch and router. The RUGGEDCOM RX1510’s modular and field replaceable platform can be equipped with WAN, serial, and Ethernet options, making it ideally suited for electric power utilities, the industrial plant floor, and traffic control systems. The appliance’s compact form factor makes it ideal for pole mount applications or installation in restricted spaces.

  • Page 11: Description

    Introduction 1.2 Description Description The RUGGEDCOM RX1510 features various ports, controls and indicator LEDs on the front panel for connecting, configuring and troubleshooting the device. Utility USB Port RS232 Serial Console Port (RJ45) Lamp Test/Alarm Cut-Off (LT/ACO) Button Compact Flash Card Port Alarm Indicator LED Port Status LEDs Management Port...

  • Page 12: Required Tools And Materials

    Introduction 1.3 Required Tools and Materials • Orange = Warning alert • Red = Configuration error Alarm Indicator LED Indicates when an alarm condition exists. • Green = Alarms cleared/acknowledged • Red = Alarm Compact Flash Card Port Houses the CompactFlash (CF) card that contains active and backup installations of RUGGEDCOM RUGGEDCOM RX1510, along with the configuration database and other system data.

  • Page 13: Cabling Recommendations

    Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions.
  • Page 14 Introduction 1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations reliable, error-free data communication, new and pre-existing communication paths should be verified for TIA/EIA-568-A compliance. The following table summarizes the relevant cabling standards: Cabling 1000Base- Required Action Category TX Compliant < 5 New wiring infrastructure required. Verify TIA/EIA-568-A compliance.
  • Page 15 Introduction 1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...

  • Page 16: Installing The Device

    Installing the Device This chapter describes how to install the device, including mounting the device, installing/removing modules, connecting power, and connecting the device to the network. DANGER Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing any maintenance tasks, make sure all power to the device has been disconnected and wait approximately two minutes for any remaining energy to dissipate.

  • Page 17: General Procedure

    This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens Canada Ltd. could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment.

  • Page 18: Unpacking The Device

    Visually inspect each item in the package for any physical damage. Verify all items are included. Note If any item is missing or damaged, contact Siemens for assistance. Mounting the Device The RUGGEDCOM RX1510 is designed for maximum mounting and display flexibility.

  • Page 19: 2.3.2 Mounting The Device To A Panel

    Installing the Device 2.3.2 Mounting the Device to a Panel Panel/DIN Rail Adapter DIN Rail Screw Figure 2.1 DIN Rail Mounting Install one of the supplied screws on either side of the device to secure the adapters to the DIN rails. 2.3.2 Mounting the Device to a Panel For panel installations, the RUGGEDCOM RX1510 can be equipped with panel/DIN rail adapters pre-installed on each side of the chassis.

  • Page 20: Connecting The Failsafe Alarm Relay

    Installing the Device 2.4 Connecting the Failsafe Alarm Relay Screw Panel/DIN Rail Adapter Figure 2.2 Panel Mounting Prepare the mounting holes Align the device with the mounting holes and secure it to the panel. Connecting the Failsafe Alarm Relay The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed when the unit is powered and there are no active alarms.

  • Page 21: 2.5.1 Connecting High Ac/Dc Power

    Installing the Device 2.5.1 Connecting High AC/DC Power Power modules can be equipped with either a screw or European-style (Euroblock) terminal block. The screw terminal block is installed using Phillips screws and compression plates, allowing either bare wire connections or crimped terminal lugs. For information about installing or removing a power module, refer to "Installing/ Removing Power Modules"...
  • Page 22 Installing the Device 2.5.1 Connecting High AC/DC Power NOTICE Electrical hazard – risk of damage to equipment Do not connect AC power cables to a 12, 24 or 48 VDC power supply terminal block. Damage to the power supply may occur. Connect the power supply terminal block to the device.
  • Page 23 Installing the Device 2.5.1 Connecting High AC/DC Power Non-removable Screw Terminal Block Positive/Live (+/L) Terminal Ground Terminal Negative/Neutral (-/N) Terminal Figure 2.5 AC Terminal Block Wiring – Screw Terminal Block for HI Power Supplies Note For secure, reliable connections under severe shock or vibration, use M3.5 ring lugs with a maximum outer diameter of 7 mm (0.28 in).

  • Page 24: 2.5.2 Connecting Low Dc Power

    Installing the Device 2.5.2 Connecting Low DC Power Using a #10 ring lug and #10-32 screw, secure the ground terminal on the power source to the ground connection on the device. Make sure the screw is tightened to 1.1 N·m (9.5 lbf·in). #10 Ring Lug #10-32 Screw Connection from External Power Source...
  • Page 25 Installing the Device 2.5.2 Connecting Low DC Power European-style (Euroblock) Terminal Block Positive (+) Terminal Negative (-) Terminal Ground Terminal Figure 2.8 DC Terminal Block Wiring – European-style (Euroblock) Terminal Block for 12P, 24P and 48P Power Supplies Not Connected Removable Screw Terminal Block Non-removable Screw Terminal Block Positive (+) Terminal Negative (-) Terminal...
  • Page 26 Installing the Device 2.5.2 Connecting Low DC Power European-style (Euroblock) Terminal Block Positive (+) Terminal Negative (-) Terminal Ground Terminal Figure 2.10 DC Terminal Block Wiring – European-style (Euroblock) Terminal Block for -12P, -24P and -48P Power Supplies Not Connected Removable Screw Terminal Block Non-removable Screw Terminal Block Positive (+) Terminal Negative (-) Terminal...
  • Page 27 Installing the Device 2.5.2 Connecting Low DC Power Note For secure, reliable connections under severe shock or vibration, use M3.5 ring tongues with a maximum outer diameter of 7 mm (0.28 in). Make sure no bare metal is exposed beyond the safety cover. Connect the positive wire from the power source to the positive (+) terminal on the terminal block.
  • Page 28 Installing the Device 2.5.2 Connecting Low DC Power #10 Ring Tongue #10-32 Screw Connection from External Power Source Ground Connection Figure 2.13 Ground Connection Install the safety cover over the terminal block. This is mandatory for 48 VDC and -48 VDC power supplies. RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...
  • Page 29 Installing the Device 2.5.2 Connecting Low DC Power RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...

  • Page 30: Device Management

    It may cause damage to the contact pins of the RJ45 ports. For a permanent solution, use Siemens 6XV1870-3Qxxx certified cables (manufactured December 2019 or after) or equivalent. Siemens recommends using Siemens certified cables and connectors for Siemens RUGGEDCOM products.
  • Page 31 Device Management 3.1 Connecting to the Device Serial Console and Management Ports Connect a workstation directly to the serial console or management ports to access the boot-time control and RUGGEDCOM RX1510 interfaces. The serial console port provides access to RUGGEDCOM RX1510's console interface, while the management port provides access to RUGGEDCOM RX1510's console and Web interfaces.

  • Page 32: Configuring The Device

    Device Management 3.2 Configuring the Device Name Description Receive Data- Transmit Data+ Reserved (Do Not Connect) Reserved (Do Not Connect) Transmit Data- Reserved (Do Not Connect) Reserved (Do Not Connect) Communication Ports Connect any of the available Ethernet ports on the device to a management switch and access the RUGGEDCOM RX1510 console and Web interfaces via the device's IP address.
  • Page 33 The following will void the warranty and potentially result in configuration data corruption/loss: • Using a CF card not approved by Siemens for use with this device • Removing the CF card in any scenario other than those described in this section...
  • Page 34 Device Management 3.3 Accessing the CompactFlash Card Remove the CF card access panel. Ejector Button CompactFlash Card Access Panel Figure 3.5 Removing the CF Card Press the ejector button to the left of the CF card and then pull the card out. Secure the CF card access panel to the chassis.
  • Page 35 Device Management 3.3 Accessing the CompactFlash Card RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...

  • Page 36: Modules

    Modules The RUGGEDCOM RX1510 features slots for up to two field-replaceable line modules, which can be used to expand and customize the capabilities of the device to suit specific applications. A variety of modules are available, each featuring a specific type of communication port: copper Ethernet, fiber optic Ethernet, SFP, WAN, cellular modem and DDS.

  • Page 37: Available Modules

    A variety of modules are available for use with the RUGGEDCOM RX1510. For more information, refer to the "RUGGEDCOM Modules Catalog [https:// support.industry.siemens.com/cs/us/en/view/109747072]" for the RUGGEDCOM RX1510. Installing/Removing Line Modules Upon installing a new line module in the device, all features associated with the module are available in RUGGEDCOM RX1510.
  • Page 38 Modules 4.3 Installing/Removing Line Modules Module Chassis Screw Figure 4.2 Removing a Module Install a new module or a blank module (to prevent the ingress of dust and dirt). [Optional] If necessary, install the device in the rack. Installing a Module To install a line module, do the following: [Optional] If the device is installed in a rack, remove it from the rack.

  • Page 39: Installing/Removing Power Modules

    Modules 4.4 Installing/Removing Power Modules Chassis Screw Figure 4.3 Installing a Module Tighten the screws to secure the module. [Optional] If necessary, install the device in the rack. Installing/Removing Power Modules The RUGGEDCOM RX1510 supports dual redundant power supply modules. Slot PS1 Slot PS2 Figure 4.4 Power Modules...
  • Page 40 Modules 4.4 Installing/Removing Power Modules Removing a Power Module To remove a power module, do the following: DANGER Electrocution hazard – risk of serious personal injury or death Make sure power to the module is turned off before servicing the power supply terminal.
  • Page 41 Modules 4.4 Installing/Removing Power Modules RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...
  • Page 42 Modules 4.4 Installing/Removing Power Modules Chassis Screws Power Supply Figure 4.5 Removing a Power Supply Slide the module out of the chassis. Disconnect the power supply wiring from the terminal block. Alternatively, for convenience, remove the terminal block with the wiring still connected and set it aside to be connected later to the new module.
  • Page 43 Modules 4.4 Installing/Removing Power Modules State Description Green The module is supplying power Green The module is receiving power RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...

  • Page 44: Technical Specifications

    Technical Specifications This section provides important technical specifications related to the device. General specifications Insulation Class I Overvoltage category OVC II Chassis Specifications Power Consumption 10 W Power Supply Specifications Note When determining cable lengths, make sure the nominal input voltage for the power supply is provided at the power source.

  • Page 45: Failsafe Relay Specifications

    Technical Specifications 5.4 Failsafe Relay Specifications Failsafe Relay Specifications Maximum Switching Voltage Rated Switching Current Isolation 30 VDC 2800 VDC for 1 minute 125 VDC 0.1 A , 0.15 A between coil and contacts 250 VAC 6.25 A Inductive load R/L = 7 ms Resistive load Operating Environment The RUGGEDCOM RX1510 is rated to operate under the following environmental...
  • Page 46 Technical Specifications 5.7 Dimension Drawings 237.7 Figure 5.1 Overall Dimensions RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...
  • Page 47 Technical Specifications 5.7 Dimension Drawings 286.5 152.4 276.4 78.2 Figure 5.2 Panel and Din Rail Mount Dimensions 162.5 151.4 19.7 Figure 5.3 Line Module Dimensions 162.5 151.8 40.6 Figure 5.4 Power Module Dimensions RUGGEDCOM RX1510 Equipment Manual, 10/2023, C79000-G8976-1055-25...

  • Page 48: Certification

    Modules Catalog" for the device available online. Approvals This section details the standards to which the RUGGEDCOM RX1510 complies. Note All relevant certificates and test reports are available on Siemens Industry Online Support [https://support.industry.siemens.com/cs/ww/en/ps/16008/cert]. 6.1.1 UKCA This device is certified for use in Great Britain and bears the United Kingdom Certified Assessed (UKCA) marking.

  • Page 49: European Union (Eu)

    Certification 6.1.3 European Union (EU) 6.1.3 European Union (EU) This device is declared by Siemens Canada Ltd. to comply with essential requirements and other relevant provisions of the following EU directives: • Directive 2014/30/EU Directive 2014/30/EU of the European Parliament and of the Council of 26...

  • Page 50: Fcc

    Title 21 Code of Federal Regulations (CFR) – Chapter I – Sub-chapter J – Radiological Health 6.1.6 ISED This device is declared by Siemens Canada Ltd. to meet the requirements of the following ISED (Innovation Science and Economic Development Canada) standard: • CAN ICES-3 (A)/NMB-3 (A) 6.1.7...

  • Page 51: Rohs

    Certification 6.1.8 RoHS 6.1.8 RoHS This device is declared by Siemens Canada Ltd. to meet the requirements of the following RoHS (Restriction of Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic equipment: • EU RoHS Directives (EU) 2011/65 and (EU) 2015/863 European Directive for Restriction of Hazardous Substances •...
  • Page 52 5 kV (Failsafe Relay output) DC Power Ports 5 kV AC Power Ports Siemens-specified severity levels. EMC Immunity Type Tests for IEEE 1613 Note RUGGEDCOM products meet Class 1 requirements for copper Ethernet configurations and Class 2 for fiber Ethernet configurations. Class 1 allows for temporary communication loss, while Class 2 requires error-free and interrupted communications.
  • Page 53 Certification 6.2 EMC and Environmental Type Tests Description Test Levels DC Power Ports 5 kV AC Power Ports Dielectric Strength Signal ports 2 kV DC Power Ports 1.5 kV AC Power Ports 2 kV Fast Transient Signal ports ± 4 kV @ 2.5 kHz DC Power Ports ±...
  • Page 54 For more information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens Canada Ltd. Digital Industries Process Automation 300 Applewood Crescent Concord, Ontario, L4K 4E5 Canada © 2023 Siemens Canada Ltd. Subject to change...

Table of Contents