HHB CDR-882 DualBurn Service Manual page 3

Table of Figures
Figure 2.1-1: Remove the four screws on the top .................................................... 6
Figure 2.1-2: Remove the six screws on the sides ................................................... 6
Figure 2.1-3: Remove the seven screws on the rear ................................................. 6
Figure 2.1-4: Push to unlock lid ......................................................................... 6
Figure 2.1-5: Interior of the unit ......................................................................... 7
Figure 2.2-1: Data and power cables on the back of the drive .................................... 8
Figure 2.2-2: Bus and power cables removal from the drive ...................................... 8
Figure 2.2-3: Bus and power cables on the motherboard .......................................... 8
Figure 2.2-4: Disconnect bus and power cables from the motherboard ........................ 9
Figure 2.2-5: Cut tie holding the power cables for drive 1 ........................................ 9
Figure 2.2-6: Twelve screws that hold the drives' brackets in place ........................... 10
Figure 2.2-7: How to reach the screw under the power switch. .................................. 9
Figure 2.2-8: Removing the drives from the chassis .............................................. 10
Figure 2.2-9: Push the eject lever under the tray to eject the disc tray ........................ 11
Figure 2.2-10: Door removal ........................................................................... 11
Figure 2.2-11: 4 screws that hold each bracket attached to the drives ........................ 11
Figure 2.2-12: Drive, brackets and door disassembled ........................................... 12
Figure 2.3-1: FFC socket on the upper board ....................................................... 13
Figure 2.3-2: Unlocking the FCC on the upper board ............................................ 13
Figure 2.3-3: FFC removal .............................................................................. 13
Figure 2.3-4: Eight screws, two stand-offs and nut and washer on the rear panel ......... 14
Figure 2.3-5: Pliers used to remove the BNC nut .................................................. 14
Figure 2.3-6: Nut-driver used to remove the serial port stand-offs ............................ 14
Figure 2.4-1: Different connectors on the motherboard .......................................... 15
Figure 2.4-2: 3 FFCs on the motherboard ........................................................... 15
Figure 2.4-3: Screws and stand-offs that hold the motherboard to the rear panel .......... 15
Figure 2.4-4: Screws that hold the motherboard to the chassis ................................. 16
Figure 2.4-5: Push to release the motherboard from the rear panel ........................... 16
Figure 2.4-6: Remove loose cables .................................................................... 17
Figure 2.5-1: Remove the four screws and disconnect the Molex type connector .......... 18
Figure 2.5-2: CDR-882 switched mode power supply ............................................ 18
Figure 2.6-1: 8 screws that hold the panel to the chassis ......................................... 19
Figure 2.6-2: 3 crews that hold the headphones board ........................................... 19
Figure 2.6-3: Six more screws that hold the front panel to the chassis ........................ 20
Figure 2.6-4: Remove the front panel ................................................................ 20
Figure 2.6-5: Front panel standing alone ............................................................ 20
Figure 2.7-1: Remove pots .............................................................................. 21
Figure 2.7-2: Release the switches board from the panel ........................................ 21
Figure 2.7-3: Unlock the FFC .......................................................................... 21
Figure 2.7-4: Separate the switches and PS2 boards .............................................. 22
Figure 2.7-5: Remove the volume pot ................................................................ 22
Figure 2.7-6: Remove all the buttons from the front panel ...................................... 22
Figure 2.7-7: Front panel and buttons ............................................................... 23
Figure 2.7-8: 4 screws that hold the LCD in place ................................................. 23
Figure 2.7-9: Front panel completely disassembled............................................... 23
Figure 2.8-1: Remove power cabling ................................................................. 24
CDR-882 Service Manual Version 1.3 Page 3 of 37