Yardworks SN70016-1 Owner's Manual
  1. Manuals
  2. Brands
  3. Yardworks Manuals
  4. Snow Blower
  5. SN70016-1
  6. Owner's manual

Yardworks SN70016-1 Owner's Manual

12 amp 16 inch snow thrower
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OWNER'S MANUAL
12 Amp 16 Inch Snow Thrower
Copyright. All Rights Reserved.
Model SN70016-1 | SKU # 270-3286
This product has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the owner 's manual before
using this product.
Thank you for your purchase.
DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY,
PARTS, SERVICE QUESTIONS? GO TO AMERICANLAWNMOWER.COM OR
CALL 1-800-633-1501. BETWEEN 8 AM – 5 PM EST, MONDAY-FRIDAY FOR
ASSISTANCE.
SAVE THIS MANUAL FOR FUTURE REFERENCE
CONFORMS TO UL
STD No.1090
CERTIFIED TO
CSA STD C22.2
No.147

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SN70016-1 and is the answer not in the manual?

Questions and answers

Related Manuals for Yardworks SN70016-1

Summary of Contents for Yardworks SN70016-1

  • Page 1 OWNER’S MANUAL 12 Amp 16 Inch Snow Thrower Copyright. All Rights Reserved. Model SN70016-1 | SKU # 270-3286 CONFORMS TO UL STD No.1090 CERTIFIED TO CSA STD C22.2 No.147 This product has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety.
  • Page 2 (2) this device must accept any interference received, including interference that may cause undesired operation. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. Model SN70016-1 SKU 270-3286...

  • Page 3: Important Safety Warnings

    SJTOWA. These cords are rated for outdoor use Be aware of the extension cord while operating the and reduce the risk of electric shock. snow thrower. Be careful not to trip on the cord. Always keep the cord away from the auger. Model SN70016-1 SKU 270-3286...
  • Page 4 WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. AVOID UNINTENTIONAL STARTING – Don’t carry plugged in hedge trimmer with finger on switch. Be sure switch is off when plugging in. Model SN70016-1 SKU 270-3286...

  • Page 5: Product Specifications

    ST4.2x30 Philips Head Self Tapping 1-800-633-1501 for assistance. Screw Adjust Knob ST3.9x55 Philips Head Self Tapping Screw Adjust Knob Cover Wheel Bracket Wheel Hub Cap Auxiliary Handle M6x50 Hex Head Bolt & Wing Nut Operator’s Manual Model SN70016-1 SKU 270-3286...

  • Page 6: Parts List

    Shaft end ring Drive belt, large Pulley frame Washer Screw M5 x 12 Left cover plate assembly Wing nut (M6x50 Hex Head Bolt) Wing nut (M6x45 Carriage Bolt) Friction plate Scraper blade Auger Auger axle 19 20 Model SN70016-1 SKU 270-3286...
  • Page 7 Secure the upper cover to the motor housing with the Install the wheels (13) and secure into place with the supplied screws. washers and M5 x 12 screws. Push wheel covers into place. Remember to connect the wire to the plug on the motor housing! Model SN70016-1 SKU 270-3286...
  • Page 8 Loosen the wing nut and adjust the angle and height of the handle to a safe and comfortable position. Secure into place by tightening the wing nut onto the bolt. M6x50 Hex Head Bolt Model SN70016-1 SKU 270-3286...
  • Page 9 Make sure all fasteners on the snow thrower (screws, nuts, etc.) are fully tightened. Check the auger for wear and tear at regular intervals. Position the snow thrower so that snow will discharge in a safe direction away from the operator and bystanders. Model SN70016-1 SKU 270-3286...
  • Page 10 To protect these parts, the motor has cooled down and you can resume normal one or two inches of snow can be left behind and cleared operation. with de-icing salt or a shovel. Model SN70016-1 SKU 270-3286...

  • Page 11: Maintenance And Storage

    3. Install new belt (13) with the drive shaft (12). 4. Secure with screws (14). 5. Replace belt (17), screw (20), washer (19) and pulley frame (18). 6. Replace the cover (21) and friction plate (24). Secure with screws. Model SN70016-1 SKU 270-3286...
  • Page 12 (26) and dismount the pulley (15) and auger axle 2. Install new scraper blade. (27). 3. Secure with the three screws.  Replace the auger with a new one. 4. Ensure the screws are properly tightened. 1XM8 Model SN70016-1 SKU 270-3286...

  • Page 13: Troubleshooting

    REPAIR PARTS Please record your serial number in the space provided below. • NAME OF ITEM Snow Thrower MODEL NUMBER SN70016-1 / SKU 270-3286 • SERIAL NUMBER Always mention the model number when ordering kits/items for this tool. Kit/Item Number...
  • Page 14 The Great States Corp. (GSC) warrants to the original owner that this Yardworks product and service part is free from defects in materials and workmanship and agrees to repair or replace any defective product or part for the warranty peri- od as stated above.

This manual is also suitable for:

270-3286

Table of Contents