Table of Contents
Advertisement
Trouble shooting
en
The settings on
The child-
the appliance
proof lock is
cannot be config-
activated.
ured. A key sym-
bol has lit up on
the display or
†'"".
The appliance
The appliance
door will not
door is locked
open. A key sym-
with the child-
bol has lit up on
proof lock.
the display.
The appliance
The appliance
door will not
door is locked
open. A lock
by the clean-
symbol H has lit
ing function.
up on the display.
The "descale"
Build-up of
symbol appears
limescale in
in the display.
appliance.
~ "Getting to
know your
appliance"
on page 9
'‚Ÿ appears in
The power
the display.
supply has
been discon-
nected or the
appliance has
been
switched off
during the
descaling pro-
cess.
There is too
"†‚-ƒƒ
appears in the
much water in
display.
the steam
system. The
water cannot
be pumped
back into the
water tank.
The appliance is
Demo mode
not heating. The
is activated.
colon is flashing
on the display. On
some appliances,
a š will also
appear on the dis-
play.
--------
:
Warning – Risk of injury!
Incorrect repairs are dangerous. Do not attempt to
repair the appliance yourself. Repairs must only be
carried out by one of our trained after-sales engineers. If
the appliance is defective, call the after-sales service.
:
Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
30
Deactivate the childproof lock by
pressing and holding the button
with the key symbol for approx. 4
seconds.
Deactivate the childproof lock by
pressing and holding the button
with the key symbol for approx. 4
seconds.
The lock can be switched off in
the basic settings.
Wait until the cooking compart-
ment has cooled down and the
lock symbol H has gone out.
Run the descaling programme in
full. ~ "Cleaning function"
on page 24
Run "Descaling interrupted" in
full. ~ "Cleaning function"
on page 24
Empty the water tank then insert
it. Touch the v button. Reset the
time. Switch off the appliance and
switch it back on again. Run "Des-
caling interrupted" in full.
~ "Cleaning function"
on page 24
Briefly disconnect the appliance
from the mains (switch off the cir-
cuit breaker in the fuse box) and
then deactivate demo mode
within approx. 5 minutes by
changing the basic setting ™‚„
or ™› to ‹. ~ "Basic settings"
on page 20
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Error messages on the display
If an error message with """ appears on the display,
e.g. "‹†-„ƒ, touch the v button. This will reset the
error message. Reset the time, if necessary.
If the fault was a one-off, you can continue to use your
appliance as normal. If the error message appears
again, call our after-sales service and quote the exact
error message and the E no. of your appliance.
~ "Customer service" on page 31
Maximum operating time
If you do not change the settings on your appliance for
several hours, the appliance will stop heating
automatically. This prevents unintentional continuous
operation.
When the maximum operating time is reached depends
on the various different settings that have been
configured on the appliance.
Maximum operating time reached
"‰ appears on the display.
Turn the function selector to the "Off" position. You can
configure new settings if required.
To prevent the appliance from switching off when
Tip:
you do not want it to, e.g. with an extremely long
cooking time, you should always set a cooking time.
The appliance will heat up until the set cooking time has
elapsed.
Advertisement
Table of Contents
