Advertisement
Quick Links
2022. 02. 28. 15:41
Water Sensor 7 Basic user guide (ZWA018)
Modified on: Thu, 16 Sep, 2021 at 3:31 PM
Aeotec Water Sensor 7 Basic.
Aeotec Water Sensor 7 has been crafted as a safety sensor to help detect and prevent floods and water leaks using Z-
Wave Plus. It is powered by Aeotec's
S2 framework. You can find out more about
that link.
To see whether Water Sensor 7 is known to be compatible with your Z-Wave system or not, please reference our
gateway comparison
(http://aeotec.com/z-wave-gateways)
(https://aeotec.freshdesk.com/a/solutions/articles/6000218908-door-window-sensor-7-technical-specifications-)
at that link.
Familiarize yourself with your Water Sensor 7 Basic.
Package contents:
1. Sensor Unit.
2. Cover.
3. Double-Sided Tape large (×2).
4. Screws (×4).
5. Dowels( x4).
https://help.aeotec.com/support/solutions/articles/6000228221-water-sensor-7-basic-user-guide-zwa018-
Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk
Gen7
(https://aeotec.com/z-wave-home-automation/z-wave-gen7.html)
Water Sensor 7
(https://aeotec.com/z-wave-door-window-sensor)
listing. The
technical specifications of Water Sensor 7
technology and
by following
Z-Wave
can be viewed
1/9
Advertisement
Related Manuals for Aeotec ZWA018
Summary of Contents for Aeotec ZWA018
- Page 1 Modified on: Thu, 16 Sep, 2021 at 3:31 PM Aeotec Water Sensor 7 Basic. Aeotec Water Sensor 7 has been crafted as a safety sensor to help detect and prevent floods and water leaks using Z- Wave Plus. It is powered by Aeotec’s...
- Page 2 Important safety information. Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.
-
Page 3: Quick Start
2022. 02. 28. 15:41 Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk Quick Start Installation of Water Sensor 7 Basic. Open the cover by pressing the clip on the side and pulling the cover upwards. Insert a fresh 1 * 1/2 AA battery, but pay attention to the polarity Install your Water Sensor 7 Basic. - Page 4 2022. 02. 28. 15:41 Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk Classic Inclusion 1. Set your Z-Wave controller into pairing mode. 2. Triple-click the tamper switch on Water Sensor 7 - this begins to blink five times 3.
-
Page 5: Advanced Functions
2022. 02. 28. 15:41 Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk When operation button is Short Pressed the LED blinks red three LowBatt time (1 sec duty cycle) If either Tamper Switch 1 or 2 is activated the device blinks red one time with ½... - Page 6 2022. 02. 28. 15:41 Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk In order to send your sensors new configuration commands from your Z-Wave controller or gateway, it will need to be woken up. 1. Wake Up the device by removing the cover.
-
Page 7: Parameter Setting
2022. 02. 28. 15:41 Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk Parameter setting. 3. Visual LED indications Parameter: 3 Size: 1 Byte Default Value: 7 Description: This parameter defines when the red LED will indicate events. Disabling all indications may extend battery life. - Page 8 2022. 02. 28. 15:41 Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk This is the BASIC command value sent in case of On even 0 - 99 - Value 255 - On 8. BASIC command value sent to 2nd Association Group on Off event...
- Page 9 2022. 02. 28. 15:41 Water Sensor 7 Pro/Basic user guide : Aeotec Help Desk 1- Reset all Parameter settings to their default settings. 1431655765 - (0x55555555) Completely factory reset sensor and send device reset locally notification Preview https://help.aeotec.com/support/solutions/articles/6000228221-water-sensor-7-basic-user-guide-zwa018-...
Need help?
Do you have a question about the ZWA018 and is the answer not in the manual?
Questions and answers