Aeotec MULTISENSOR 6 User Manual
  1. Manuals
  2. Brands
  3. Aeotec Manuals
  4. Security Sensors
  5. MULTISENSOR 6
  6. User manual

Aeotec MULTISENSOR 6 User Manual

Hide thumbs Also See for MULTISENSOR 6:
Table of Contents

Advertisement

Quick Links

See also: Manual
Enlarged version
Warning
Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities.
Contact your local government for information regarding the
collection systems available.
Certifications (regional):
Z-Wave and Z-Wave Plus are registered
trademarks of Sigma Designs and its subsidiaries in
the United States and other countries
FCC ID: XBAFT100
Version: 501010000001-AA
www.aeotec.com
MULTISENSOR 6
View the expanded manual:
http://aeotec.com/support

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MULTISENSOR 6 and is the answer not in the manual?

Questions and answers

Related Manuals for Aeotec MULTISENSOR 6

Summary of Contents for Aeotec MULTISENSOR 6

  • Page 1 Contact your local government for information regarding the collection systems available. Certifications (regional): Z-Wave and Z-Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the United States and other countries MULTISENSOR 6 FCC ID: XBAFT100 View the expanded manual: http://aeotec.com/support Version: 501010000001-AA www.aeotec.com...
  • Page 2 THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including...
  • Page 3 INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED Aeotec by Aeon Labs’ MultiSensor looks like a motion sensor and it BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION acts like one too. But it’s also so much more. Installing this 1 piece IN CONTRACT, OR TORT, OR OTHERWISE EVEN IF ADVISED OF of Z-Wave®...
  • Page 4 Excluded from the warranty are problems due to accidents, acts of God, civil or military authority, civil disturbance, war, strikes, fires, other catastrophes, misuse, misapplication, storage damage, negligence, electrical power problems, or modification to the Products or its components. Aeon Labs does not authorize any person or party to assume or create for it any other obligation or liability in connection with the Products except as set forth herein.
  • Page 5 3V, 1500mAh). Quick start. Operating Temperature: 0 to 40 . Setup your power. Measured Temperature Range: -10 to 50 . Accuracy: ±0.5 . Humidity Range: 20%RH to 80%RH. Accuracy: ±5%RH (at 25 ). Your MultiSensor can be powered by battery or by USB with Lighting: 0 LUX to 1000 LUX.
  • Page 6 Z-Stick or a you may also wish to reset all of your MultiSensor’s settings to their Minimote from Aeotec. If you’re using an alternative controller for factory defaults. To do this, press and hold the Z-Wave Button for your Z-Wave network, please refer to its user manual for network 20 seconds and then release it.
  • Page 7 Parameter 111-113 [4 byte decimal] can be configured through your If your Z-Stick is plugged into a gateway or a computer, unplug it. gateway in case the default settings of your MultiSensor are not Take your Z-Stick to your MultiSensor. what you desire.
  • Page 8 seconds, then inclusion has been successful. If the LED blinks Setting automatic report flags. when the button is pressed, the inclusion has been unsuccessful Parameter 101-103 [4 byte dec] can be configured through your and you should repeat the above steps. gateway in case the default settings of your MultiSensor are not Press any button on your Minimote to return it to standard what you desire.
  • Page 9 For example, this parameter setting is initially set to 240 which is the delay time in 4 minutes or 240 seconds.You may set the value to the desired Motion Sensor delay time to any amount of seconds as you like. So if you want the time out to be 5 minutes after the Motion Sensor is triggered, set this parameter to the value of 300.
  • Page 10 For optimal performance, your MultiSensor should NOT be Press the Action Button on your MultiSensor. mounted directly on or near metal framing or other large metallic If your MultiSensor has been successfully removed from your objects. Large metal objects may weaken the Z-Wave wireless network, its LED will blink when you press the Action Button.
  • Page 11 Battery Holder If your Z-Stick is plugged into a gateway or a computer, unplug it. Take your Z-Stick to your MultiSensor. Press and hold the Action Button on your Z-Stick for 3 seconds and then release. USB port Press the Action Button on your MultiSensor. Attach your desired mounting accessory.
  • Page 12 Z-Wave network’s main controller to do this and the following instructions tell you how to do this using Aeotec by Aeon Labs’ Z-Stick and Minimote controllers. If you are using other products as your main Z-Wave controller, please refer to the part of their respective manuals that tells you how remove devices from your network.

Table of Contents