Timer - Whirlpool ACQ088PV Use And Care Manual

Sleep Control
NOTES:
If the current room temperature is 80ºF (26ºC) or higher, the
set temperature will not change when Sleep control is
activated.
If the current room temperature is below 80ºF (26ºC), the set
temperature will automatically increase 2ºF (1ºC) during the
first 2 hours after Sleep control is activated.
The set temperature will not increase during the last 6 hours
of Sleep control.
1. Press MODE to select Cool, Heat (Heat/Cool models only) or
Dry.
2. Press FAN to select High, Med or Low.
3. Press the up or down arrow button to set the temperature.
4. Press SLEEP. After 10 seconds, the lights on the control
panel display will dim. The mode indicator lights will remain
on.
NOTE: The mode, temperature and fan speed may be
adjusted during Sleep control. After 10 seconds, the lights on
the control panel display will dim again.
5. To turn off Sleep control, press SLEEP again. or wait 8 hours
for the air conditioner to turn off automatically.
NOTE: The air conditioner will return to previous settings after
Sleep control is turned off.
Temperature
Press the up arrow button to raise the temperature. Each time
you press or hold the up arrow button, the temperature will go
up 2ºF (1ºC) until it reaches 90°F (32°C).
Press the down arrow button to lower the temperature. Each
time you press or hold the down arrow button, the
temperature will go down 2ºF (1ºC) until it reaches 64°F
(18°C).

Timer

To set Timer for a 30-minute to 24-hour delay before air
conditioner is turned off (air conditioner must be On):
1. Press TIMER. Timer indicator light on the air conditioner
control panel will flash.
2. Press up or down arrow button to change the delay time from
30 minutes to 24 hours.
3. After 5 seconds, Timer indicator light on the air conditioner
control panel will remain on.
To set Timer to turn on air conditioner, keeping previous
settings:
1. Turn off the air conditioner.
2. Press TIMER. Timer indicator light on the air conditioner
control panel will flash.
3. Press up or down arrow button to change the delay time from
30 minutes to 24 hours.
4. After 5 seconds, Timer indicator light on the air conditioner
control panel will remain on.
To set Timer to turn on air conditioner, changing the
previous settings:
1. Turn on air conditioner.
th
2. Adjust the mode to 6 Sense
Heat (Heat/Cool models only) or RapidCool
3. For Cool or Heat (Heat/Cool models only) mode:
Adjust fan speed to High, Med, Low or Auto.
Adjust temperature between 64ºF and 90ºF (18ºC and
32ºC).
4. For Fan mode, adjust fan speed to High, Med or Low.
NOTE: In Fan mode, temperature cannot be set.
5. For 6 th Sense ™ System control, adjust fan speed to High,
Med, Low or Auto.
6. For Dry mode and 6 th Sense
temperature up or down by 4ºF (2ºC).
7. Turn off air conditioner.
8. Press TIMER. Timer indicator light on the air conditioner
control panel will flash.
9. Press up or down arrow button to change the delay time from
30 minutes to 24 hours.
10. After 5 seconds, Timer indicator light on the air conditioner
control panel will remain on.
To clear Timer delay program:
NOTE: Air conditioner can be either on or off.
1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, press TIMER
again. Timer indicator light will turn off.
To see or change the remaining time (in hours):
1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, press the
plus or minus TEMP button to increase or decrease the time.
3. After 5 seconds, the display will show the current room
temperature.
™
System control, Cool, Dry, Fan,
™ control.
™ System control, adjust
13