Payment System Setup; Complete Installation; User & Setup Instructions; General User Information - Maytag MHN33PD Installation Instructions Manual

If the washer is against a wall, move the washer out slightly
before tipping back. If the washer is not level, fi rst prop the
front with a wood block and adjust the feet as necessary.
To adjust feet, use a 14 mm (9/16") open-end or adjustable
wrench to turn jam nuts clockwise (as viewed from above) on
feet until they are about 13 mm (1/2") from the washer cabinet.
Then turn the leveling foot counterclockwise to lower the
washer or clockwise to raise the washer. Recheck levelness of
washer and that all four feet are fi rmly in contact with the fl oor.
Repeat as needed.
2. Make sure all four feet are stable and resting on the fl oor.
Then check that the washer is perfectly level (use a level).
3. When washer is level and all four feet are fi rmly in contact with
the fl oor, use a 14 mm (9/16") open-end or adjustable wrench
to turn jam nuts counterclockwise (as viewed from above) on
leveling feet tightly against washer cabinet.
Jam nut
Jam nut
IMPORTANT: All four feet must be tightened. If the nuts are
not tight against the washer cabinet, the washer may vibrate.
4. The washer should not move front to back, side to side, or
diagonally when pushed on its top edges.
5. Slide the washer to its fi nal location.
6. Confi rm the levelness of the washer.

Payment System Setup

PD Model Washer is coin payment ready and allows the use of
two different sizes of coins if a dual drop is installed. To set up
the washer for coin payment, acquire a coin drop mechanism
with the appropriate coin sensors. Connect coin sensors to coin
slots 1 and 2, respectively.
1. Door must be closed before cycle selection is made.
2. Press fabric setting keypad for the wash cycle desired. After
the cycle is started, the time will display and count down.

General User Information

'0 Minutes' showing in display
This indicates the previous cycle is complete or a machine reset
was performed. Opening the door will restore the display to the
vend price or available state.
Factory Default Setting
Washer is programmed at the factory as follows:
■ Normal and Delicates cycles have an 11 minutes wash
period and 2 rinses, with the option of an extra rinse.
■ The Powerwash cycle has 3 minutes of Prewash, a
14 minutes wash period and 4 rinses, with the option to
deselect the extra rinse.
12
USER & SETUP INSTRUCTIONS

Complete Installation

1. Check the electrical requirements. Be sure that you have
the correct electrical supply and the recommended earthing
method. See "Electrical Requirements."
2. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
3. Check that you have all of your tools.
4. Dispose of/recycle all packaging materials.
5. Check that the water taps are on.
6. Check for leaks around taps and inlet hoses.
WARNING
Electrical Shock Hazard
Plug into a grounded (earthed) outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
7. Plug into an earthed socket outlet.
8. To test and to clean your washer, measure 1/2 the detergent
manufacturer's recommended amount for a medium-size load.
Pour the detergent into the detergent dispenser. Select any
cycle and allow the washer to complete one whole cycle.
■ $1.75 wash price for Normal and Delicates cycles, $2.00 for
Powerwash (PD models).
■ $0.00 wash price (PR models).
Warm Start (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, 'RESELECT CYCLE' will fl ash
in the display, indicating the need for a keypad press to restart
washer.
Door Lock
The door will be locked when the cycle starts. The door will
remain locked until the end of a cycle or approximately 2 minutes
after a power interruption.
After the door is opened following the completion of a cycle, the
display indicates the cycle price (unless set for free operation). As
coins are inserted or debit inputs arrive, the display will change to
acknowledge valid coin or debit inputs.