Maytag MHN33PD Installation Instructions Manual page 16

Code Explanation
J. Ed Enhanced Debit is self-selected when a
Generation 2 card reader is installed in the
washer. The Ed option cannot be manually
selected or deselected.
Press the LOWER MIDDLE keypad once to advance to next code.
L. 00 PRICE SUPPRESSION OPTION
This option causes the customer display to show
'ADD' or 'AVAILABLE' rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected 'OFF.'
L. PS Selected 'ON.' Press the UPPER RIGHT keypad
once for this selection.
Press the LOWER MIDDLE keypad once to advance to next code.
n. CE CLEAR ESCROW OPTION
When selected, money held in escrow for
30 minutes without further escrow or cycle
activity will be cleared.
n 00 Not Selected 'OFF'.
n CE Selected 'ON'. Press the UPPER RIGHT keypad
once for this selection.
Press the LOWER MIDDLE keypad once to advance to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the UPPER RIGHT keypad. Factory
default of 800 rpm.
Press the LOWER MIDDLE keypad once to advance to next code.
A1. 03 PREWASH LENGTH
A1. 03 This is the number of minutes of PREWASH.
Select between 2 and 7 minutes by pressing the
UPPER LEFT keypad to increase or the LOWER
LEFT keypad to decrease.
Press the LOWER MIDDLE keypad once to advance to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of fi nal high speed
spin. Choose from 3–8 minutes by pressing the
UPPER LEFT keypad to increase or the LOWER
LEFT keypad to decrease.
Press the LOWER MIDDLE keypad once to advance to next code.
A3. 02 NORMAL CYCLE SETTINGS
A3. 02 Allows the owner to select the cycle default
options of Water Temperature, Prewash, and
Extra Rinse.
See Table 1 for specifi c settings. Normal is set
to 02 from the factory. The UPPER LEFT and
LOWER LEFT keypads change the values.
A4. 00 DELICATES CYCLE SETTINGS
A4. 00 Allows the owner to select the cycle default
options of Water Temperature, Prewash, and
Extra Rinse.
See Table 1 for specifi c settings. Delicates is set
to 00 from the factory. The UPPER LEFT and
LOWER LEFT keypads change the values.
A5. OF POWERWASH CYCLE SETTINGS
16
Code Explanation
A5. OF Allows the owner to select the cycle default
options of Water Temperature, Prewash, and
Extra Rinse.
See Table 1 for specifi c settings. PowerWash is
set to OFF from the factory. The UPPER LEFT and
LOWER LEFT keypads change the values.
Press the LOWER MIDDLE keypad once to advance to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Represents the number of
cycles in HUNDREDS
2 00 Represents the number of
cycles in ONES
This is "VIEW ONLY" and cannot be cleared.
Press the LOWER MIDDLE keypad once to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 00 Number of dollars in
HUNDREDS
4 00 Number of dollars in ONES
5 00 Number of CENTS
END OF SETUP PROCEDURES
EXIT FROM SETUP MODE
■ PD Models: Reinstall access door.
■ PR Models:
– Unplug washer or disconnect power.
– Open console, reinsert plug into Service Connection, close
console.
– Plug in washer or reconnect power.
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for
0 vend price without any Special Pricing setup, and the Coin/
Debit Option must be set to "J._d". If the washer is not in failure
mode, the door must be opened to proceed.
To enter the Service Access Code, press these keypads in the
following order: 1–upper left, 2–lower right, 3–upper right, 4–lower
left.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15 seconds delay before it
can be attempted again.
There are 3 options to exit from the Service Mode:
1. Power down the washer; then reapply power.
2. Wait 2 minutes without touching any keypads (without
diagnostic modes running).
3. From Set-Up Code 8, press keypad #1 for 4 seconds.
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225
3 01 = $100.00
4 68 = $ 68.00
5 75 = $ 00.75
TOTAL = $168.75