Labnet AccuPlate D0410 Instruction Manual

Labnet AccuPlate D0410 Instruction Manual

Laboratory stirrer/hot plate
Hide thumbs Also See for AccuPlate D0410:

Advertisement

Quick Links

Labnet AccuPlate
Stirrer/Hot Plate
Instruction Manual
Catalog Numbers:
Stirrer:
Hot Plate:
D0410
D0400
D0410-230V
D0400-230V
Laboratory
Stirring Hot Plate:
D0420
D0420-230V

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AccuPlate D0410 and is the answer not in the manual?

Questions and answers

Summary of Contents for Labnet AccuPlate D0410

  • Page 1 Labnet AccuPlate Laboratory ™ Stirrer/Hot Plate Instruction Manual Catalog Numbers: Stirrer: Hot Plate: Stirring Hot Plate: D0410 D0400 D0420 D0410-230V D0400-230V D0420-230V...
  • Page 2: Table Of Contents

    Table of Contents 1.0 Safety Information ................1 1.1 Product Voltages .
  • Page 3: Safety Information

    1.0 Safety Information This instruction manual contains important operating and maintenance instructions that must be read, understood, and followed by the product user. Failure to use this product according to this instruction manual may degrade or defeat the protection normally provided by this product.
  • Page 4: Operating Conditions

    2.0 Operating Conditions Labnet AccuPlate™ hot plates, stirrers, and stirring hot plates, are designed to be safe when used under the following conditions: Product should be placed on a flat surface at least 12 in. (30.5 cm) from walls, 48 in. (122 cm) from ceilings, and 12 in. (30.5 cm) ...
  • Page 5: Stirring Instructions

    5.0 Stirring Instructions Models D0410 and D0420 1. Fill the vessel with solution to be stirred. 2. Place the stir bar into the vessel. 3. Place the vessel in the center of the top surface. 4. Turn the Stir Control Knob until the Stirring Speed Display shows the desired speed. The speed setting can be adjusted according to the table below.
  • Page 6: Heating Operation

    See Section 10.0 for ordering information. CAUTION: The top surface and the vessel used may be at substantially higher temperatures than indicated by the setting on the Heating Temperature Display as the controller regulates the liquid temperature inside the vessel. LABNET ACCUPLATE LABORATORY STIRRER/HOT PLATE...
  • Page 7: Safety

    7.2 Safety The microprocessor-controlled system has built-in error routines to detect product operation in some unfavorable conditions. The type of error routines which may be active in a product varies depending upon the functionality of the model and the operating software version.
  • Page 8: Accessories

    Accessories (Shown with Cat. No. D0420) Cat. No. Description Labnet Stirrer/Hot Plate Accessory Kit D0461 Kit includes: External temperature controller (Cat. No. D0462), vertical support rod (Cat. No D0466) and stir bar retriever External temperature controller for digital display hot plates and stirring hot plates. Use with D0400 and D0420 models.
  • Page 9: Frequently Asked Questions

    Using a 600 mL beaker with 400 mL of water at 25°C, it takes approximately 15 minutes to bring the water to a full, rolling boil. Can I use a metal tray on top of my Labnet hot plate? ...
  • Page 10: Equipment Disposal

    (WEEE), this product is marked with the crossed-out wheeled bin and must not be disposed of with domestic waste. Consequently, the buyer shall follow the instructions for reuse and recycling of waste electronic and electrical equipment (WEEE) provided with the products and available at www.corning.com/weee. LABNET ACCUPLATE LABORATORY STIRRER/HOT PLATE...
  • Page 11 To request certificates, please contact us at www.labnetlink.com. Warranty/Disclaimer: Unless otherwise specified, all products are for research use or general laboratory use only.* Not intended for use in diagnostic or therapeutic procedures. Not for use in humans. These products are not intended to mitigate the presence of microorganisms on surfaces or in the environment, where such organisms can be deleterious to humans or the environment.

Table of Contents