Installation - Be Cool saturn Manual

EN
A Forward-facing: 76-150cm, Weight: 9-36KG. Rotate
to adjust before effect.
90° hover. Note: This status can only be used when
B
install the child. Do not keep this state when driving.
C Rearward-facing: 40-105cm, Weight: 0-18KG, Effect
after rotation , adjustment.
3.10- USAGE OF RECLINING SYSTEM
Find the angle adjuster 12, l lift up and adjust the seat angle
forward or backward at the same time.
A Rearward-facing, 40-105cm, 0-18KG, Adjust to Gear
R. B Forward-facing, 76-105cm 9-18KG, Adjust to Gear
01/02/03/04/05/06, 105-150cm, 15-36KG, Adjust to
Gear 01.

4.1 INSTALLATION

4.1- INSTALLED REARWARD-FACING
Usage : ISOFIX+Support leg, Height: 40-105cm
Step 1) Raise the seat slightly (take out the support legs
19 from the grooves of the base) and then make the
34
support legs 90° perpendicular to the ground (see 3.8)
Step 2) If the vehicle is not equipped with ISOFIX guide
sleeve 20, it needs to be installed as shown in the
figure.
Step 3) Push ISOFIX on both sides of the base and clip
it into the ISOFIX guide sleeve. When a "click" is heard,
the ISOFIX release button 17 is displayed in green color.
Step 4) Press and hold the adjustment button on the
support leg 19 to adjust the length up and down until
it contacts the vehicle ground, and the bottom of the
support leg will be shown green.
Step 5) Turn the rotartion adjuster 13 to rotate the seat
to the 90° hover direction, then place the child on the
safety seat, lock the buckle 18 and tighten the front
tether 14.
Step 6) Turn the rotation adjuster 13. and adjust the
90° hover state to rearward-facing. The vehicle can
only drive after hearing the "click" sound.
*On the premise of not causing discomfort to children,
tighten the shoulder belt as much as possible.
*The crotch strape should be as low as possible and
should be located close to the crotch, not the abdomen.
*To ensure the comfort of your child, the safety belt
must not be twisted.
Pay attention!! Do not driving when the safety seat in
the location of 90° hover.
4.2- INSTALLED FORWARD-FACING
Usage : ISOFIX+Support leg Height: 76-105cm
A Small Headrest+Cushion. B Triangle sponge.
Step 1) First, open the support leg to 90º 19.
Step 2) If the vehicle is not equipped with ISOFIX guide
sleeve 20 it needs to be installed as shown in the figure.
Step 3) Push ISOFIX on both sides of the base and clip
it into the ISOFIX guide sleeve. When a "click" is heard,
the ISOFIX release button 17 is displayed in green color.
Step 4)Press and hold the adjustment button on the
support leg 19 to adjust the length up and down until
it contacts the vehicle ground, and the bottom of the
support leg will be shown green.
Step 5) Put the child in the safety seat, and lock the
buckle 8, tighten the front tether 14.
Pls adjust the angle adjuster under the seat to choice a
comfortable angle.
4.3- INSTALLED FORWARD-FACING
Usage 1: ISOFIX + 3 point belt. Height: 105-150cm
Step 1) Store the support leg 19.
A Press and hold the adjustment button on the support
leg, and stow the support leg.
B Then lift the seat and fold the support leg back into
the seat bottom groove.
C Finally, push the front protruding part inward.
Step 2) If the vehicle is not equipped with ISOFIX
guide sleeve 20, it needs to be installed as shown in
the figure.
Step 3) Push ISOFIX on both sides of the base and
clip it into the ISOFIX guide sleeve. When a "click" is
heard, the ISOFIX release button 17 is displayed in
green color.
* See page 14, 3.6 "How to store the buckle and shoul-
der strap sleeve" to remove the parts.
EN
35