Husqvarna DC 2-48 Operator's Manual page 8

Do not use electrical adapters with the product.
Extension cables
• Use only approved extension cables with applicable
properties.
• The rated value on the extension cable must be the
same or higher than given on the rating plate of the
product.
• Use grounded extension cables.
• When you operate the product outdoors, use
an extension cable that is applicable for outdoor
operation. This decreases the risk of electrical
shock.
• Keep the connection to the extension cable dry and
off the ground.
• Keep the extension cable away from heat, oil, sharp
edges or moving parts. A damaged cable increases
the risk of electrical shock.
• Make sure that the extension cable is in good
condition and not damaged.
• Do not use the extension cable while it is wound up.
This can cause the extension cable to become too
hot.
• Make sure that the extension cable is out of the
way and the product during operation. This prevents
damage to the extension cable.
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
• Do not use the product if the safety devices are
damaged or does not operate correctly.
• Do a check of the safety devices daily. If your safety
devices are damaged or does not operate correctly,
speak to your Husqvarna service agent.
• Do not make modifications on safety devices
Emergency stop button
The emergency stop button is used to quickly stop the
product and breaks the mains power supply.
To do a check of the emergency stop button
Control panel overview on page 4 for
Refer to
information about where the emergency stop button is
on your product.
1. Turn the emergency stop button clockwise to make
sure that the emergency stop button is disengaged.
2. Start the product. Refer to
page 11 .
3. Push the emergency stop button.
4. Make sure that the motor stops.
5. Turn the emergency stop button clockwise to
disengage.
8
Read the warning
To start the product on
Motor protection switch
The product has multiple motor protection switches to
prevent motor overload. Let an electrician do a check
of the motor protection switches if there is a motor
overload.
Safety instructions for maintenance
WARNING:
instructions that follow before you do
maintenance on the product.
• Product related accidents can occur during the
troubleshooting, servicing and maintenance as the
operator must be in the risk area of the product. The
operator must be careful, make a plan and prepare
the work to prevent accidents.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Use personal protective equipment. Refer to
Personal protective equipment on page 6 .
• Disconnect the product from the power source
before you do the maintenance.
• Do not make modifications to the product.
Modifications that are not approved by the
manufacturer can cause serious injury or death.
• Always use original accessories and spare parts.
Accessories and spare parts that are not approved
by the manufacturer, can cause serious injury or
death.
• Replace damaged, worn or broken parts.
• Only do the maintenance as given in this operator's
manual. Let an approved service agent do all other
servicing.
• If the replacement of the supply cord is necessary,
this has to be done by the manufacturer or his agent
in order to avoid a safety hazard.
• Only let an approved electrician do all checks of the
electric components.
• Be careful when you handle the filters. If you
damage the filters, there is a risk of dust dispersion.
• The manufacturer, or an instructed person, must
do a technical inspection at least annually. The
technical inspection includes an inspection of the
filters for damage, air tightness of the product and
correct function of the control mechanism. In addition
the filtration efficiency of the product must be tested
at least annually, or more frequently as may be
specified by national requirements. If the test is not
conducted the main filters must be replaced by new
ones.
• When carrying out service or repair operations, all
contaminated items which cannot be satisfactorily
cleaned are to be disposed of; such items shall be
disposed of in impervious bags in accordance with
any current regulation for the disposal of such waste.
• All the machine parts shall be regarded as
contaminated when removed from the working
Read the warning
2121 - 002 - 04.07.2023