Unigas PN91 Manual Of Installation - Use - Maintenance page 32

BURNER EXPLODED VIEW
ITEM DESCRIPTION
1.1 NIPPLE
1.2 ELBOW
1.3 NIPPLE
1.4 PUMP
2.1.1 POWER CONTROLLER
2.1.2 FRONT CONTROL PANEL
2.1.3 LIGHT
2.1.4 LIGHT
2.1.5 LOCK-OUT RESET BUTTON
2.1.6 PROTECTION
2.1.7 SWITCH
2.1.8 SWITCH
2.2 BRACKET
2.3 BOARD
2.4 COVER
3.1.1 LONG IGNITION ELECTRODE
3.1.2 LONG IGNITION ELECTRODE
3.1.3 COMBUSTION HEAD
3.1.4 IGNITION CABLE
3.2 GUN TERMINAL
3.3 STANDARD COMPLETE OIL GUN
3.3.1.1 NIPPLE
3.3.1.2 RESISTOR FIXING SCREW
3.3.1.3 OIL MANIFOLD
3.3.1.4 RESISTOR
3.3.2 NOZZLE
3.3.3 NOZZLE HOLDER
3.4 OIL GUN HOLDER
3.5 COMBUSTION HEAD ADJUSTING PIPE
4.1 SPACER
4.2 FAN WHEEL
4.3 MOTOR
4.4 GAUGE RING
5.1 STRAIGHT UNION
5.2.1 OIL FILTER
ITEM DESCRIPTION
5.2.2 GASKET
5.2.3 GAS BLEEDING VALVE
5.2.4 THERMOMETER
5.2.5 MUFF
5.3 COVER
5.4 REDUCTION
5.5 OIL PRE-HEATER
5.6 SHEATH
5.7 RESISTOR
6.1 NIPPLE
6.2 STRAIGHT JOINT
6.3 UNION ELBOW
6.4 OIL SOLENOID VALVE
6.5 REDUCTION
6.6 OIL MANIFOLD
6.7 CONNECTOR
7.1 UNION ELBOW
7.2 STRAIGHT UNION
7.3 UNION ELBOW
7.4 SCREW
7.5 ADJUSTING ROD
7.6 REDUCTION
7.7 WASHER
7.8 BUSH
7.9 BEARING
7.10 PRESSURE GOVERNOR
7.11
7.12 BRACKET
7.13 BRACKET
8.1.1 SPACER
8.1.2 BUSH
8.1.3 ACTUATOR
8.1.4 ACTUATOR SHAFT
8.1.5 BRACKET
8.2 NET
ITEM DESCRIPTION
8.3 AIR INTAKE DAMPER
8.4 AIR INTAKE DAMPER
8.5 AIR INTAKE
8.6 LOUVER SHAFT
8.7 LOUVER SHAFT
8.8 ADJUSTING CAM SHAFT
8.9 ADJUSTING CAM
8.10.1 SCREW
8.10.2 SCREW
8.10.3 SPACER
8.10.4 CAM
8.10.5 LEVERAGE
8.10.6 ROD
8.10.7 JOINT
8.10.8 JOINT
9.1 FAIRLEAD
9.2 FAIRLEAD
10 AIR INLET CONE
11 BURNER HOUSING
11.1 COVER
12 GENERATOR GASKET
13 RING NUT
14 INSPECTION GLASS
15 PHOTORESISTOR
16.1 PIN
16.2 ELASTIC RING
16.3 ELASTIC RING
16.4 HALF-COUPLING
16.5 HALF-COUPLING
16.6 HALF-COUPLING
16.7 HALF-COUPLING
17 BRACKET
18 RESISTOR
19 STANDARD BLAST TUBE