Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita TW004GM201
Summary of Contents for Makita TW004GM201
- Page 1 INSTRUCTION MANUAL Cordless Impact Wrench TW004G TW005G Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: TW004G TW005G Fastening capacities Standard bolt M10 - M20 High tensile bolt M10 - M16 Square drive 12.7 mm No load speed (RPM) Max impact mode 0 - 3,200 min Hard impact mode 0 - 2,600 min Medium impact mode 0 - 1,800 min Soft impact mode 0 - 1,000 min... -
Page 3: Ec Declaration Of Conformity
Save all warnings and instruc- WARNING: Wear ear protection. tions for future reference. WARNING: The noise emission during actual The term "power tool" in the warnings refers to your use of the power tool can differ from the declared mains-operated (corded) power tool or battery-operated value(s) depending on the ways in which the tool is (cordless) power tool. - Page 4 Remove any adjusting key or wrench before Maintain power tools and accessories. Check for turning the power tool on. A wrench or a key left misalignment or binding of moving parts, break- attached to a rotating part of the power tool may age of parts and any other condition that may affect the power tool’s operation. If damaged, have result in personal injury.
- Page 5 It may result in a risk of CAUTION: Only use genuine Makita batteries. overheating, possible burns and even an explosion. Use of non-genuine Makita batteries, or batteries that If electrolyte gets into your eyes, rinse them out have been altered, may result in the battery bursting with clear water and seek medical attention right causing fires, personal injury and damage. It will...
-
Page 6: Functional Description
Overheat protection FUNCTIONAL DESCRIPTION This protection works when the tool or battery is over- heated. In this situation, let the tool and battery cool CAUTION: Always be sure that the tool is before turning the tool on again. switched off and the battery cartridge is removed before adjusting or checking function on the tool. Overdischarge protection This protection works when the remaining battery Installing or removing battery cartridge capacity gets low. In this situation, remove the battery from the tool and charge the battery. - Page 7 Switch action ► 1 . Button ► 1 . Switch trigger To turn on the lamp status, press the button for one second. To turn off the lamp status, press the button for one second again. With the lamp status ON, pull the switch trigger to turn on CAUTION: Before installing the battery car- the lamp. To turn off, release it. The lamp goes out approxi-...
-
Page 8: Changing The Application Mode
This tool has a reversing switch to change the direction of rota- tion. Depress the reversing switch lever from the A side for clock- wise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral posi- tion, the switch trigger cannot be pulled. - Page 9 Example of application Application mode Example of application (Impact force grade displayed on panel) 4 (Max) Assembling steel frames and tightening long screws or bolts. 3 (Hard) Assembling steel frames. Assembling or disassembling scaffolds and frameworks. 2 (Medium) 1 (Soft) Assembling furniture. NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button NOTE: All lamps on the switch panel go out when the tool is turned off to save the battery power. The impact force grade can be checked by pulling the switch trigger to the extent that the tool does not operate.
- Page 10 Changing the application mode This tool employs several easy-to-use application modes for driving bolts with good control. The type of the application mode changes every time you press the button . You can change the application mode within approximately one minute after releasing the switch trigger. NOTE: You can extend the time to change the application mode approximately one minute if you press the button Application mode Feature Purpose (Assist type displayed on panel) Bolt mode Clockwise Clockwise This mode helps to repeat screwdriving continuously with Preventing over equal torque. This mode also helps to reduce the risk of tightening of bolts. breakage of bolts/nuts due to overtightening. Counterclockwise Counterclockwise Loosening bolts.
- Page 11 NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button NOTE: All lamps on the switch panel go out when the tool is turned off to save the battery power. The type of the application mode can be checked by pulling the switch trigger to the extent that the tool does not operate. Tool with the ring spring Full speed mode For TW004G For impact socket without O-ring and pin ► 1 . Button 2.
-
Page 12: Operation
Tool with the detent pin OPERATION For TW005G CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red indicator on the upper side of the button, it is not locked completely. Insert it fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. ► 1 . Impact socket 2. Hole 3. Square drive 4. Detent Align the hole in the side of the impact socket with the detent pin on the square drive and push the impact socket onto the square drive until it locks into place. -
Page 13: Maintenance
NOTE: Hold the tool pointed straight at the bolt or nut. NOTE: Excessive fastening torque may damage the CAUTION: These accessories or attachments bolt/nut or impact socket. Before starting your job, are recommended for use with your Makita tool always perform a test operation to determine the specified in this manual. The use of any other proper fastening time for your bolt or nut. accessories or attachments might present a risk of injury to persons. Only use accessory or attachment... - Page 16 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885804-225 www.makita.com 20200630...