Evenflo Pivot Vizor - Travel System with LiteMax Infant Car Seat Manual

Evenflo Pivot Vizor - Travel System with LiteMax Infant Car Seat Manual

Also See for Pivot Vizor:

Advertisement

Evenflo Pivot Vizor - Travel System with LiteMax Infant Car Seat Manual

Features

Holds Evenflo SafeMax™ or LiteMax™ Infant Car Seats Only

Features

  1. Canopy
  2. Canopy Window
  3. Parent Handle
  4. Cupholder
  5. Toddler Seat Release Button
  6. Swivel Wheel
  7. Lower Privacy Cover
  8. Buckle
  9. Harness Covers (only on certain models)
  10. Bumper Bar/ Storage Pouch
  11. Child Tray
  12. Shoulder Straps
  13. Upper Privacy Cover
  14. Multi-Position Recline Handle
  15. Fold Latch
  16. Multi-Position Recline Strap
  17. Side Frame Lock
  18. Storage Basket
  19. Brakes

Important Information

Child Requirements - When stroller is in carriage mode, it is intended for a child up to 6 months of age. Only use the stroller in the upright position with a child who is capable of sitting upright unassisted.

  • Maximum weight: 55 lbs (25 kg)
  • Maximum height: 40 inches (101.6 cm)


Read instructions carefully before use. Save these instructions for future reference. It is very important to assemble the stroller according to these instructions. If you are missing parts, do not use stroller and call Evenflo ParentLink at 1-800-233-5921 (U.S.A.), 1-937-773-3971 (Canada), or 800-706-1200 (México) to order replacement parts.

Registration Information
Please register this product so we can reach you if there is a safety alert or recall. We will not sell, rent, or share your personal information. To register your product, please complete and mail the card that came with it or visit our online registration at www.evenflo.com/registerproduct.

Identification of Parts

Choosing Mode of Use

YOUR STROLLER SEAT CAN BE USED IN TWO DIFFERENT MODES.
TODDLER SEAT MODE OR CARRIAGE MODE
.
Your stroller seat is shipped in carriage mode with the buckles unfastened under the footrest. You will need to follow the instructions completely to make sure you set up your stroller in your preferred mode of use.

After the frame and the wheels have been assembled, you can choose to set the stroller up in Carriage Mode or Toddler Seat Mode by following instructionsю

Toddler Seat Mode
Toddler Seat Mode

Carriage Mode
Carriage Mode

Assembling Your Stroller - Frame


DEATH or SERIOUS INJURY can occur.
Care must be taken when folding or unfolding stroller to prevent finger injury in hinge areas.

To protect flooring, place a protective covering (carton) beneath the stroller during assembly.
Unlatch side frame lock. Continue holding the lock open while unfolding the stroller.
Assembling Your Stroller - Frame - Step 1

Grab the parent's handle and pull upward until the stroller opens fully with an audible click.
Assembling Your Stroller - Frame - Step 2

Make sure the stroller is locked in the open position by pushing down on the parent's handle.
Assembling Your Stroller - Frame - Step 3

Assembling Your Stroller - Wheels

Turn the stroller so the front of the stroller is facing upwards as shown.
To attach front wheels, push wheel onto front leg tube until it clicks into place. Repeat on other side.
Pull on wheels to make sure both of them are securely attached.
Assembling Your Stroller - Wheels - Step 1

Turn the stroller upside down as shown so the rear of the stroller is facing upwards.
To attach rear wheels, push wheel onto rear leg tube until it clicks into place. Repeat on other side.
Pull on wheels to make sure both of them are securely attached.
Assembling Your Stroller - Wheels - Step 2

Assembling Your Stroller - Toddler Seat Mode

To set up seat in toddler seat mode, flip toddler seat over and attach the buckle on the seat as shown.
Toddler Seat Mode - Step 1
Toddler Seat Mode - Step 2

To attach toddler seat, slide seat onto the mounts until they both click into place on both sides of the frame. The toddler seat may be attached forward or rear-facing.
CHECK to make sure it is securely attached by pulling up on it.
NOTE: Stroller cannot be folded with seat in rear-facing position.
Toddler Seat Mode - Step 3
To attach bumper bar, push tabs into openings on stroller on either side of frame until it clicks into place.
Pull on the bumper bar to make sure it is locked into place.

To remove the bumper bar, push both tabs and remove the bumper bar from the stroller.
Toddler Seat Mode - Step 4

To attach child tray, insert the tab on the tray into the slot on the bumper bar as shown.
To remove child tray, pull up and remove from the slot.
Toddler Seat Mode - Step 5

To remove storage pouch from bumper bar, unzip storage pouch as shown.
Toddler Seat Mode - Step 6

Using Your Stroller - Toddler Seat Mode to Carriage Mode


DEATH or SERIOUS INJURY can occur.

NEVER use seat in a reclined carriage position unless straps under seat are unbuckled and seat is set up in reclined carriage mode as per the instructions.

If you are in Toddler Seat Mode as shown, follow these steps to convert to Carriage Mode.
Toddler Seat Mode to Carriage Mode - Step 1

To recline seat, squeeze button and pull down the recline strap on the rear of seat.
Toddler Seat Mode to Carriage Mode - Step 2

Unfasten buckle behind leg rest on toddler seat. Refer to Step 1 for buckle location.
Toddler Seat Mode to Carriage Mode - Step 3

Lift handle and rotate seat all the way down so that it is flat.

To avoid spills, remove child tray when reclining the toddler seat.
Toddler Seat Mode to Carriage Mode - Step 4

Press down on the inside of the toddler seat to flatten out the inside.
Toddler Seat Mode to Carriage Mode - Step 5
Toddler Seat Mode to Carriage Mode - Step 6

To remove and use in rear facing mode: Press the release buttons on both sides of toddler seat, lift seat off stroller frame and turn it around and re-attach.
Toddler Seat Mode to Carriage Mode - Step 7

CHECK to make sure it is securely attached on both sides by pulling up on it.
Toddler Seat Mode to Carriage Mode - Step 8

Using Your Stroller - Brakes


DEATH or SERIOUS INJURY can occur.

ALWAYS lock brakes. Make sure brakes are on by trying to push the stroller.

To lock, press brake lever DOWN on rear wheel brake as shown.
Using Your Stroller - Brakes - Step 1

To unlock, lift brake lever UP on rear wheel brake as shown.
Using Your Stroller - Brakes - Step 2

Using Your Stroller - Cupholder

To attach cupholder, slide down on the mount on either side of stroller as shown.
Using Your Stroller - Cupholder - Step 1

To remove cupholder, press tab towards center and slide up as shown.
Using Your Stroller - Cupholder - Step 2

Using Your Stroller - Harness


DEATH or SERIOUS INJURY can occur.

To avoid serious injury from falling or sliding out, ALWAYS use waist restraint.

NOTE: Verify the stroller is locked in the open position by pushing down on the parent's handle.
Lock the rear brakes and remove the bumper bar.
The harness shoulder straps must be at shoulder height or lower, closest to the baby's shoulders .

Place the baby in the seat and bring the crotch panel up between the child's legs. Fasten each buckle . For a snug, comfortable fit, pull the shoulder straps to tighten the shoulder restraint and pull the waist restraint straps to tighten the waist restraint.
NOTE: To loosen the waist straps , push in the release button L on the buckle and pull.

To loosen shoulder straps push up on the retainer while pulling down on the shoulder strap.
Once the child is properly restrained, re-attach the bumper bar.
Make sure the bumper bar locks into position with audible clicks.
Pull on the bumper bar to make sure it is locked into place.

Using Your Stroller - Canopy

To open or close canopy, push to the front or the rear of the stroller.
Using Your Stroller - Canopy - Step 1

Canopy has a window that can be rolled back so you can view child.
Using Your Stroller - Canopy - Step 2

To remove canopy, unfasten canopy mounts from sides of toddler seat as shown.
Using Your Stroller - Canopy - Step 3

Unfasten hook and loop tape from top edge of canopy as shown. Repeat on other side of canopy.
Using Your Stroller - Canopy - Step 4

Using Your Stroller - Attaching Privacy Cover to Toddler Seat

NOTE: Bumper bar must be installed in order to use privacy cover.
To attach privacy cover to toddler seat, unzip bumper bar and pull upper privacy cover out. Fully extend canopy and zip upper privacy cover to canopy as shown.

Canopy must be fully extended before attaching upper privacy cover to toddler seat.
Attaching Privacy Cover to Toddler Seat - Step 1

Remove lower privacy cover from storage pouch and zip to lower section of storage pouch as shown.
Attaching Privacy Cover to Toddler Seat - Step 2

Attach side hooks from upper and lower privacy covers to fabric loops on the sides of toddler seat.
Attaching Privacy Cover to Toddler Seat - Step 3

Pull lower privacy cover over bottom of toddler seat and attach hook and loop straps to fabric.
NOTE: When using Privacy Cover in toddler seat mode or carriage mode, make sure to open the canopy window.
Attaching Privacy Cover to Toddler Seat - Step 4

Using Your Stroller - Attaching Privacy Cover to Infant Car Seat

To attach privacy cover to infant car seat, remove lower privacy cover from storage pouch and zip to fully extended infant car seat canopy as shown.


Canopy must be fully extended before attaching privacy cover to infant car seat.
Attaching Privacy Cover to Infant Car Seat - Step 1

Attach side hooks from lower privacy cover to fabric loops on the sides of infant car seat.
Attaching Privacy Cover to Infant Car Seat - Step 2

Pull lower privacy cover over bottom of infant car seat and attach hook and loop strap as shown.
Attaching Privacy Cover to Infant Car Seat - Step 3

To remove child from infant car seat without removing the privacy cover, disconnect hook and loop attachments from front of seat and disconnect side hooks from infant car seat. Lift front of privacy cover and attach hook and loop strap to back of canopy.
For more room for legs, attach hook and loop strap to middle and fold open as shown.
Attaching Privacy Cover to Infant Car Seat - Step 4

Using Your Stroller - Folding Stroller


DEATH or SERIOUS INJURY can occur.

Care must be taken when folding or unfolding stroller to prevent finger injury in hinge areas.
To fold the stroller, remove your child, adjust seat back to upright position, lock the rear brakes, and close the canopy.
Pull the levers on both sides of the stroller and lower frame until the side frame lock clicks into place.
NOTE: Stroller cannot be folded with seat in rear-facing position or with upper privacy cover zipped onto canopy.
Using Your Stroller - Folding Stroller - Step 1

For more compact fold, you can remove the toddler seat before folding the stroller frame.
NEVER fold the stroller when the toddler seat is in the carriage mode.
Using Your Stroller - Folding Stroller - Step 2

Using your Stroller with the Recommended Infant Car Seats on your Stroller Frame


DEATH or SERIOUS INJURY can occur.

  • Only use Evenflo SafeMax™ infant car seats or any version of the LiteMax™ infant car seat with this stroller. Other infant car seats or carriers are not designed to fit the stroller frame and if used with this stroller may result in serious injury to your child.
  • Before using the infant car seat with this stroller, read all the instructions provided with it and keep the instructions stored properly for future use.
  • DO NOT lift stroller by using the infant car seat handle when installed on stroller.
  • If unable to securely attach your infant car seat to this stroller, remove the car seat and contact Evenflo ParentLink at 1-800-233-5921 (USA), 1-937-773-3971 (Canada), or 800-706-1200 (México).
  • To avoid serious injury, make sure the infant car seat is securely snapped onto the car seat mounts.
  • Some Evenflo SafeMax™ and LiteMax™ infant car seats have a blanket/boot option that must be removed for proper attachment to this stroller.
  • To avoid serious injury or death, DO NOT use privacy cover when installing Infant Car Seat in vehicle rear facing without the base.

To remove the toddler seat, press the release buttons down on both sides of the toddler seat and lift seat off stroller frame.
Recommended Infant Car Seats - Step 1

To attach car seat, insert car seat into the mounts until they both click into place on both sides of the frame.
Recommended Infant Car Seats - Step 2
Recommended Infant Car Seats - Step 3
NOTE: The infant car seat may be installed facing the parent or facing forward on the stroller frame.

Pull up on the front and back of the infant car seat to test that it is properly locked into place.
Recommended Infant Car Seats - Step 4

TO REMOVE, squeeze handle on rear of seat and pull car seat up off of the stroller.
Recommended Infant Car Seats - Step 5

Care and Maintenance

  • Clean minor spills and stains on cloth or plastic surfaces with cold water and mild soap. Air dry.
  • Metal and plastic parts can be wiped clean with a soft damp cloth and dried with a soft cloth. DO NOT use abrasive cleaners or solvents

Safety Instructions


DEATH or SERIOUS INJURY can occur.

READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS! FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH!

  • Only use Evenflo SafeMax™ and LiteMax™ infant car seats with this stroller. Other infant car seats or carriers are not designed to fit the stroller frame and if used with this stroller may result in serious injury to your child.
  • NEVER leave child unattended. ALWAYS keep child in view while in the stroller.
  • Adult assembly required. Take care when unpacking and assembling; contains small parts and some items with sharp edges.
  • To prevent a possible choking hazard, remove and discard packing material before using this product.
  • Avoid serious injury from falling or sliding out. ALWAYS use waist restraint.
  • DO NOT carry or roll stroller on stairs or escalators with child in it.
  • DO NOT hang items on handle bar or place them on the canopy as they can tip stroller over and injure child.
  • Be sure stroller is fully assembled and locked in unfolded position before using.
  • ALWAYS exercise care when going over curbs or steps, and never use stroller for anything other than transporting your child. Push stroller at a normal walking pace only; faster strolling can cause a loss of control and injury to the child.
  • DO NOT place hot liquids in cup holder. Spills can burn you or your child.
  • To avoid serious injury from child falling out of stroller, DO NOT raise or recline seat with child in stroller.
  • DO NOT use stroller if any parts are missing or broken.
  • DO NOT allow child to climb on, into, out of, or around stroller.
  • DO NOT allow child to stand on the footrest. Stroller may tip over and injure child.
  • DO NOT carry additional children, goods, or accessories in or on this stroller except as advised in these instructions. The stroller is intended for use with one child and to accommodate only the additional weights in storage as listed in these instructions.
  • Care must be taken when folding or unfolding stroller to prevent finger injury to you or your child in hinge areas. Make sure child is not in the seat or near the stroller when folding or unfolding.
  • NEVER leave stroller on a hill or incline, even with brakes set. Stroller may tip, injuring the child.
  • To avoid accidental rolling, ALWAYS set brakes when stroller is not being pushed.
  • AVOID STRANGULATION:
    • DO NOT suspend strings or toys from the canopy.
    • DO NOT place stroller anywhere near cords from window blinds, draperies, phone, etc.
    • DO NOT place items with a string around your child's neck such as hood strings or pacifier cords.
    • If not properly secured, the child may slip into leg openings and strangle.
  • When making adjustments to the stroller, ALWAYS ensure that all parts of the child's body are clear of any moving parts of the stroller.
  • The canopy is not intended to provide UV protection.
  • Sharp or heavy objects placed in pockets may cause damage to the stroller, or injury to the child.
  • To ensure safety for your baby, please refer to the manufacturer's instructions for the use of your recommended infant car seats and keep all instructions available for reference.
  • DO NOT lift stroller by using the infant car seat handle when installed on stroller.
  • If unable to securely attach the infant car seat to this stroller, remove the car seat and contact Evenflo ParentLink at 1-800-233-5921 (USA), 1-937-773-3971 (Canada), or 800-706-1200 (México).
  • To avoid stroller instability and tip-overs, DO NOT load cup holder with over 1 lb (0.45 kg), and the main cargo basket with over 10 lbs (4.5 kg).
  • NEVER use the toddler seat without the canopy attached.
  • NEVER lift or carry the toddler seat by the bumper bar.
  • NEVER use the stroller frame without the toddler seat or car seat attached.
  • NEVER use toddler seat in a motor vehicle or use it as a booster seat.
  • To avoid falls, never remove toddler seat from the stroller with child in it.
  • To avoid falls, always make sure the toddler seat or car seat is securely attached into the seat mounts on both sides of the stroller before placing child in the seat.
  • When stroller seat is in carriage mode, it is intended for a child up to 6 months of age.
  • NEVER use seat in the carriage mode position unless the straps under the seat are unbuckled and the seat is set up in carriage mode as per the instructions.
  • To avoid overheating, make sure to open the canopy window when using privacy cover in toddler seat mode or carriage mode.
  • To avoid serious injury or death, DO NOT use privacy cover when installing Infant Car Seat in vehicle rear facing without the base.

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Evenflo Pivot Vizor - Travel System with LiteMax Infant Car Seat Manual

Advertisement

Need help?

Need help?

Do you have a question about the Pivot Vizor and is the answer not in the manual?

Questions and answers

Table of Contents