Page 6
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP ONE: Disconnect the battery, ground first and then power wire. GROUND POWER ENGINE SUPPLY LINE PRESSURE RELIEF STEP TWO: • Squeeze the hose clamp and slide it back. • Disconnect both fuel lines. •...
Page 7
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP THREE: Install the foam marker pump assembly. NOTE: If the machine is equipped with 35 gallon tank, see the next page for lower bracket assembly. • Attach the lower support bracket to the side of the hopper with 3/8”...
Page 8
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS 35 GALLON TANK ATTACHMENT • Attach the lower support bracket to the back of the 35 gallon tank frame with 3/8” X 1” carriage bolts. • Attach the upper support bracket & the gas tank sup- port.
Page 9
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS • Attach the foam marker assembly to the support bracket (2) 1/4” X 1/2” carriage bolts.
Page 10
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP FOUR: • Connect one end of the 3/8” hose to barb fitting on the motor. • Route the hose down and along the inside of the hopper. • Zip tie the hose to the support bracket. Zip tie...
Page 11
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP FIVE: • Connect the other end of the 3/8” hose to the barb tee fitting. STEP SIX: • Attach the foam marker bracket to the end of the boom. NOTE: • Repeat step four for the other side of the boom.
Page 12
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS • Attach the foam marker bracket to the end of the boom. NOTE: • Repeat this step for the other side. • Note the orientation of the bracket for left and right side. Fig. 1 6 NOZZLE BOOM OPTION LEFT SIDE...
Page 13
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP SEVEN: LEFT SIDE • Attach the foam marker dropper to the brack- et, securing it with 3/8” hose and hose clamp. NOTE: Instructions are the same for the 6 nozzle spray boom (see Fig. 1 page 11). •...
Page 14
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP EIGHT: RIGHT SIDE • Attach the foam marker dropper to the brack- et, securing it with 3/8” hose and hose clamp. NOTE: Instructions are the same for the 6 nozzle spray boom, both sides (see Fig. 1 page 11). •...
Page 16
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP NINE: • Remove the plastic cap from “aux 3” in the panel . • Attach the “rocker switch” to the dash panel. NOTE: The long side of the rocker switch should face down. LONG SIDE •...
Page 17
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP TEN: Continue to route the wiring harness down through the uprights attaching it with zip ties as necessary. STEP ELEVEN: • Connect the ground wire from the wiring har- ness to the up right cross member. •...
Page 18
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP THIRTEEN: • Reinstall the fuel tank. • Squeeze the hose clamp and slide it back. • Reconnect both fuel lines. CAUTION! -Beware of excess fuel in the lines. -Fuel spillage. ENGINE SUPPLY LINE PRESSURE RELIEF WARNING! -Flammable gas.
Page 19
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS OPERATION FILLING THE TANK CAUTION! • Wear safety goggles & all proper clothing when operating, servicing or refilling this machine. • Always read & follow manufactures recommendations when handling any chemical. • Do not pump combustible liquids or vapors with this product. •...
Page 20
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS • Start the machine and activate the foam marker and let it prime until it starts dropping suds. • Turn the foam marker and machine off, Adjust the foam marker for desired timing. - Flow control valve, adjust the flow control valve for more or less flow.
2.5 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS TROUBLE SHOOTING PROBLEM SOLUTION • ADD MORE FOAM CONCENTRATE TO THE TANK. • CHECK FOR HOLES IN THE AIR LINE. • CHECK FOR PINCHED AIR OR LIQUID LINES. NOT ENOUGH FOAM • CLEAN SCREEN-STRAINER/FOAM HEAD. •...
Page 24
MADE IN THE USA Steel Green Mfg. 824 S State Road 39 MANUAL MANUAL DESCRIPTION Lebanon, IN 46052 PART NO. REV. PART NO. (765)-481-2890 SGM-003 2.5 GALLON FOAM MARKER SG46/52 KIT K299501 www.steelgreenmfg.com...
Need help?
Do you have a question about the SG36 and is the answer not in the manual?
Questions and answers