STEELGREEN SG36 Instruction Manual
Hill side assist attachment
Hide thumbs
Also See for SG36:
- Instruction manual (24 pages) ,
- Operator's manual (16 pages) ,
- Installation manual (8 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for STEELGREEN SG36
Summary of Contents for STEELGREEN SG36
- Page 1 INSTRUCTION MANUAL HILL SIDE ASSIST ATTACHMENT Models: SG36, SG42, SG46, & SG52...
- Page 2 HILL SIDE ASSIST INSTALLATION HILL SIDE ASSIST KIT A10040 SG 46/52 ITEM QTY PART NUMBER DESCRIPTION 6389K557 7/8" NYLON SLEEVE, BEARING, STRAIGHT STEER 91847A515 7/16-20 JAM NUT, STRAIGHT STEER 92373A367 1/4" X 7/8" SS ROLL PIN, STRAIGHT STEER 965K352 1.5" X .50D COMPRESSION SPRING, STRAIGHT STEER H80601 CYLINDER, CASTER LOCK W22-141-R...
- Page 3 HILL SIDE ASSIST INSTALLATION HILL SIDE ASSIST KIT A10040 SG 36/42 ITEM QTY PART NUMBER DESCRIPTION 6389K557 7/8" NYLON SLEEVE, BEARING, STRAIGHT STEER 91847A515 7/16-20 JAM NUT, STRAIGHT STEER 92373A367 1/4" X 7/8" SS ROLL PIN, STRAIGHT STEER 965K352 1.5" X .50D COMPRESSION SPRING, STRAIGHT STEER H80601 CYLINDER, CASTER LOCK W22-154-R...
-
Page 4: Right Side
HILL SIDE ASSIST INSTALLATION RIGHT SIDE... -
Page 5: Left Side
HILL SIDE ASSIST INSTALLATION LEFT SIDE... - Page 6 HILL SIDE ASSIST INSTALLATION...
- Page 7 HILL SIDE ASSIST INSTALLATION STEP ONE: Disconnect the battery, ground first and then power wire. GROUND POWER NOTE: Instructions are the same for both the right and left side, STEPS 2– 3 STEP TWO: • Remove the bolt and front tire.
- Page 8 HILL SIDE ASSIST INSTALLATION • Remove the dust cover. • Remove the cotter pin and nut which will release the yoke through the bottom.
- Page 9 HILL SIDE ASSIST INSTALLATION STEP THREE: • Install the yokes W22-144 provided with the kit. • Secure the yoke with the nut and carter pin. • Re-install the dust cover.
- Page 10 HILL SIDE ASSIST INSTALLATION • Re-install the front tire. NOTE: Regrease the bearings and housing. STEP FOUR: NOTE: If your machine is older than mid Octo- ber 2021: You will need to either • Drill mounting holes in BOTH SIDES of the chassis using the dimensions in (Fig 1)or attach the cylinder assembly to the top of the chassis (STEPS 4&5) and use the...
- Page 11 HILL SIDE ASSIST INSTALLATION STEP FIVE: Attach the solenoid valve assembly (provided with the kit) to the upright on the RIGHT SIDE. Using the 1/4 x 2 hex bolts, wash- ers, and nuts provided with the kit. NOTE: • Some parts not shown for clarity. •...
- Page 12 HILL SIDE ASSIST INSTALLATION STEP SIX: • Remove the knee pad to access the hy- draulic oil reservoir. • Loosen and remove the cap from the hydraulic oil reservoir. • Disconnect the rear hoses from the hy- draulic pumps, place the hoses over a proper container draining the hydraulic oil.
- Page 13 HILL SIDE ASSIST INSTALLATION STEP SEVEN: • Disconnect the return hose and fitting from the pump. • Connect 1 H84031 “swivel tee fitting” (provided with the kit) to the return port. • Reconnect the “swivel elbow fitting to the end of the “swivel tee fitting”.
- Page 14 HILL SIDE ASSIST INSTALLATION • Reconnect the return hose to “swivel tee fitting”. STEP EIGHT: • Disconnect the supply hose. • Connect 1 (H84031) “swivel tee fitting”, (provided with the kit) to the control valve . • Reconnect the supply hose.
- Page 15 HILL SIDE ASSIST INSTALLATION STEP NINE: Hose Routing • Connect one end of hose with “orange wrap” to the elbow fitting on the hydro pump. ORANGE • Connect the other end of hose with “orange wrap” to port 3 of the solenoid valve.
- Page 16 HILL SIDE ASSIST INSTALLATION • Connect one end of hose with “red wrap” to the swivel tee fitting on the hydraulic control valve. • Connect the other end of hose with “red wrap” to port “1” on the solenoid valve.
- Page 17 HILL SIDE ASSIST INSTALLATION • Connect the elbow end of hose with “blue wrap” to port 2 on the solenoid valve. BLUE • Connect the straight end of hose with “blue wrap” to the elbow fitting on the end of the cylinder (RIGHT SIDE OF THE MACHINE).
- Page 18 HILL SIDE ASSIST INSTALLATION • Connect the elbow end of hose with “green wrap” to port 4 on the solenoid valve. GREEN • Connect the straight end of hose with “green wrap” to the elbow fitting on the bottom of the cylinder (RIGHT SIDE OF THE MACHINE).
- Page 19 HILL SIDE ASSIST INSTALLATION • Connect the end of hose with “black wrap” to the swivel tee fitting (PORT 4). BLACK • Route the hose behind and around the engine and connect the other end of hose with “black wrap” to the elbow fitting on the bottom of the cylinder (LEFT SIDE OF THE MACHINE).
- Page 20 HILL SIDE ASSIST INSTALLATION • Connect one end of hose with “white wrap” to the swivel tee fitting (PORT 2). WHITE • Route the hose behind and around the engine and connect the other end of hose with “white wrap” to the elbow fitting on the end of the cylinder (LEFT SIDE OF THE MACHINE).
- Page 21 HILL SIDE ASSIST INSTALLATION SG-HSA...
- Page 22 HILL SIDE ASSIST INSTALLATION STEP TEN: • Using a utility or exacto knife, cut out the right side switch opening on top of the dash. • Attach the rocker switch in the opening with the long side of the switch facing down.
- Page 23 HILL SIDE ASSIST INSTALLATION • Connect the ground wire from the harness to the ground nut on the cross member. • Route the harness down the bundle with the other wire harnesses and neatly zip tie them together. • Connect the plug from wire harness to the hsa valve.
- Page 24 HILL SIDE ASSIST INSTALLATION • Connect the power wire from the harness to the power wire from the pump switch. • Connect the ignition wire from the harness to the spade connecter on the ignition switch. • Reconnect the battery, ground first and then power wire. GROUND POWER...
- Page 25 HILL SIDE ASSIST INSTALLATION STEP ELEVEN: NOTE: Check that all hose connections are tight. • Refill the hydraulic oil to the proper level. • Start the machine and activate the hill side assist a couple times or until the oil is through the system and the cylinders are functioning.
- Page 26 HILL SIDE ASSIST INSTALLATION NOTES:...
- Page 27 HILL SIDE ASSIST INSTALLATION NOTES:...
- Page 28 MADE IN THE USA Steel Green Mfg. 824 S State Road 39 MANUAL MANUAL DESCRIPTION Lebanon, IN 46052 PART NO. REV. PART NO. Steelgreenmfg.com A10040 SGM-023 SG HILL SIDE ASSIST A10040-36 (765)-481-2890...
Need help?
Do you have a question about the SG36 and is the answer not in the manual?
Questions and answers