Page 1 ® R&S SMW-K54/-K86/-K142/-K147 IEEE 802.11a/b/g/n/j/p/ac/ax/be User Manual (;ÙÑa2) 1175674902 Version 27...
Page 2 This document describes the following software options: ● R&S ® SMW-K54 IEEE 802.11a/b/g/n/j/p (1413.4139.xx) ● ® R&S SMW-K86 IEEE 802.11ac (1413.5635.xx) ● ® R&S SMW-K142 IEEE 802.11ax (1414.3259.xx) ● R&S ® SMW-K147 IEEE 802.11be (1413.6677.xx) ® This manual describes firmware version FW 5.20.043.xx and later of the R&S SMW200A.
Page 3: Table Of Contents
® Contents R&S SMW-K54/-K86/-K142/-K147 Contents 1 Welcome to the IEEE 802.11 WLAN digital standard......7 Key features........................7 Accessing the IEEE 802.11 WLAN dialog..............8 What's new........................8 Documentation overview....................9 1.4.1 Getting started manual....................9 1.4.2 User manuals and help....................9 1.4.3 Tutorials...........................9 1.4.4 Service manual.......................
Page 4 ® Contents R&S SMW-K54/-K86/-K142/-K147 3.4.5 Data settings......................... 54 A-MPDU settings......................60 MAC header and FCS configuration for frame block..........62 3.6.1 MAC header and FCS....................63 3.6.2 802.11 MAC frame field....................63 3.6.3 Beacon settings......................67 3.6.4 Trigger frame settings....................74 MAC header HT/HE and VHT configuration.............. 81 3.7.1 Common settings......................
Page 5 ® Contents R&S SMW-K54/-K86/-K142/-K147 6.1.3 Clock settings......................121 General commands....................122 Filter/clipping settings....................125 Trigger settings......................131 Marker settings......................137 Clock settings......................141 Antenna configuration settings................142 Frame block configuration..................145 Frame configuration settings...................152 6.9.1 Frame block PPDU configuration................152 6.9.2 EHT/HE configuration....................168 6.9.3 User configuration....................... 176 6.9.4 MPDU configuration....................
Page 6 ® Contents R&S SMW-K54/-K86/-K142/-K147 User Manual 1175.6749.02 ─ 27...
Page 7: Welcome To The Ieee 802.11 Wlan Digital Standard
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMW-K54/-K86/-K142/-K147 Key features 1 Welcome to the IEEE 802.11 WLAN digital standard The options R&S SMW-K54/-K86/-K142/-K147 are firmware applications that add func- tionality to generate signals in accordance with the wireless LAN standards IEEE 802.11a/b/g/n/ac/p/j/ax/be.
Page 8: Accessing The Ieee 802.11 Wlan Dialog
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMW-K54/-K86/-K142/-K147 What's new VHT-20 MHz, VHT-40 MHz, VHT-80 MHz, VHT-80+80 MHz, VHT-160 MHz ● Support of all 11ax transmission modes with option R&S SMW-K142: HE-20 MHz, HE-40 MHz, HE-80 MHz, HE-80+80 MHz, HE-160 MHz ●...
Page 9: Documentation Overview
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMW-K54/-K86/-K142/-K147 Documentation overview Compared to the previous version there are editorial changes only. 1.4 Documentation overview This section provides an overview of the R&S SMW user documentation. Unless speci- fied otherwise, you find the documents at: www.rohde-schwarz.com/manual/smw200a 1.4.1 Getting started manual Introduces the R&S SMW and describes how to set up and start working with the prod-...
Page 10: Instrument Security Procedures
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMW-K54/-K86/-K142/-K147 Documentation overview The service manual is available for registered users on the global Rohde & Schwarz information system (GLORIS): https://gloris.rohde-schwarz.com 1.4.5 Instrument security procedures Deals with security issues when working with the R&S SMW in secure areas. It is avail- able for download on the internet.
Page 11: Videos
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMW-K54/-K86/-K142/-K147 Notes on screenshots 1.4.10 Videos Find various videos on Rohde & Schwarz products and test and measurement topics on YouTube: https://www.youtube.com/@RohdeundSchwarz On the menu bar, search for your product to find related videos. Figure 1-1: Product search on YouTube 1.5 Scope Tasks (in manual or remote operation) that are also performed in the base unit in the...
Page 12: About The Ieee 802.11 Wlan Options
® About the IEEE 802.11 WLAN options R&S SMW-K54/-K86/-K142/-K147 About IEEE 802.11 WLAN technology 2 About the IEEE 802.11 WLAN options 2.1 Required options The basic equipment layout for generating IEEE 802.11 WLAN signals includes: ● Standard or wideband baseband generator (R&S SMW-B10/-B9) ●...
Page 13 ® About the IEEE 802.11 WLAN options R&S SMW-K54/-K86/-K142/-K147 About IEEE 802.11 WLAN technology IEEE 802.11ax is aimed to improve the user experience and network performance in dense deployments in the 2.4 GHz and 5 GHz band. It supports uplink and downlink multi user MIMO and up to 160 MHz bandwidth.
Page 14: Operation Modes
® About the IEEE 802.11 WLAN options R&S SMW-K54/-K86/-K142/-K147 Operation modes Parameters 802.11a 802.11b 802.11g 802.11j 802.11p Subcarrier spacing 312.5 312.5 312.5 312.5 312.5 (kHz) Symbol time (us) Cyclic prefix (us) Transmission tech- SISO SISO SISO SISO SISO nology Modulation OFDM DSSS DSSS, OFDM...
Page 15 ® About the IEEE 802.11 WLAN options R&S SMW-K54/-K86/-K142/-K147 Operation modes Figure 2-1: PLCP packet format for IEEE 802.11n 1 = Operation mode "Legacy" 2 = Operation mode "Mixed Mode" 3 = Operation mode "Green Field" Table 2-3 gives an overview of the frequency domain operation modes of the physical layer.
Page 16: Signal Generation
® About the IEEE 802.11 WLAN options R&S SMW-K54/-K86/-K142/-K147 Signal generation 2.4 Signal generation The generation of an IEEE 802.11n/ac/ax signal is done in multiple steps. In high throughput (HT) and very high throughput (VHT) modes, the data of a single user is specially coded and transmitted via up to eight Tx antennas.
Page 17: Wlan Configuration And Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 General settings 3 WLAN configuration and settings Access: ► Select "Baseband > IEEE 802.11". The remote commands required to define these settings are described in Chapter 6, "Remote-control commands", on page 118. ● General settings......................
Page 18 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 General settings Sample Rate......................... 20 Transmit Antennas Setup....................20 Filter/Clipping Settings....................20 State Activates the standard and deactivates all the other digital standards and digital modu- lation modes in the same path. Remote command: on page 124 [:SOURce<hw>]:BB:WLNN:STATe Set to Default...
Page 19 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 General settings Parameter Value "Space Time Streams" "Extended Spatial Streams" "Space Time Block Coding" inactive Parameter value "MCS" "Data Rate (Mbps)" "Data Bits Per Symbol" "Stream 1" QPSK "Channel Coding" "Coding Rate" ½ "Guard"...
Page 20 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 General settings Remote command: on page 122 [:SOURce<hw>]:BB:WLNN:SETTing:CATalog? on page 123 [:SOURce<hw>]:BB:WLNN:SETTing:LOAD on page 123 [:SOURce<hw>]:BB:WLNN:SETTing:STORe on page 123 [:SOURce<hw>]:BB:WLNN:SETTing:DELete Generate Waveform File With enabled signal generation, triggers the instrument to save the current settings of an arbitrary waveform signal in a waveform file with predefined extension *.wv.
Page 21: Transmit Antenna Setup
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Transmit antenna setup 3.2 Transmit antenna setup Access: ► Select "Baseband > IEEE 802.11 > General > Transmit Antennas Setup". This dialog is used to map the generated Tx chains to different destinations ("Base- band A/B", "File"...
Page 22 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Transmit antenna setup Transmission Antenna Table Configures the output matrix and transmission chain matrix coefficients. During signal calculation, the R&S SMW evaluates the transmission chain matrix and takes into account the set phase ratios. However, the power ratio of the antennas is not considered.
Page 23: Frame Block Configuration
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Frame block configuration 3.3 Frame block configuration Access: ► Select "Baseband > IEEE 802.11 > Frame Blocks". This tab provides settings to select and configure a frame block. Settings: Std..........................23 Type..........................24 Physical Mode.......................25 Mode........................
Page 24 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Table 3-1: Availability "Standard", "Type", "Physical Mode", "TxMode" Standard Type Physical mode Txmode User 11a/g Data/Beacon/Trigger Legacy L-20MHz L-Duplicate L-Upper L-Lower 11b/g Data/Beacon/Trigger Legacy PBCC 11p/j Data/Beacon/Trigger Legacy L-10MHz Mixed Mode/Green Field HT-20MHz HT-40MHz HT-Duplicate...
Page 25 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Frame block configuration "Beacon" A frame of type "Beacon" contains all the information about a net- work, for example the beacon interval, capability information and the IBSS parameter set. The access point (AP) of a service set periodi- cally transmits the beacon frame to establish and maintain the net- work.
Page 26 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Table 3-3: Tx modes for "Type > Data/Trigger" and "Physical Mode > Mixed Mode" Tx mode Transmission bandwidth 20 MHz 40 MHz 80 MHz 160 MHz 320 MHz HT-20MHz HT-40MHz HT-Duplicate HT-Upper HT-Lower...
Page 27 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Table 3-5: Tx modes for "Type > Sounding" and "Physical Mode > Mixed Mode" Tx mode Transmission bandwidth 20 MHz 40 MHz 80 MHz 160 MHz 320 MHz HT-20MHz HT-40MHz HT-Duplicate HT-Upper HT-Lower...
Page 28 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Frames Sets the number of frames to be transmitted in the current frame block. Remote command: on page 147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:FCOunt Idle Time /ms Sets the time interval separating two frames in this frame block. Remote command: on page 149 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:ITIMe...
Page 29 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Remote command: on page 147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BOOSt PPDU When clicking "Conf ...", accesses the settings for configuring the PPDU of frame blocks. See Chapter 3.4, "PPDU configuration", on page 30. Remote command: n.a.
Page 30: Ppdu Configuration
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration 3.4 PPDU configuration This chapter describes the physical protocol data unit (PPDU) settings. Access: ► Select "Frame Blocks > PPDU > Conf...". The dialog provides settings to configure PPDU parameters. Available settings depend on the WLAN 802.11 standard, frame type, physical mode and Tx mode.
Page 31 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration This dialog provides settings to configure spatial streams. Settings Spatial Streams......................31 Space Time Streams.....................31 Extended Spatial Streams.....................31 Multi User MIMO......................31 Segment........................32 Space Time Block Coding..................... 32 Spatial Streams Displays or sets the number of spatial streams. Setting the parameter requires, that the number of transmit antennas is higher than one, see Chapter 3.2, "Transmit antenna...
Page 32 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Segment Requires a two segment channel, e.g. "Tx Mode > HE-80+80MHz". Example: To set segments for fixed transmission bandwidth For "Transmission Bandwidth > 80 MHz" and "Tx Mode > VHT-80+80MHz", you can select one of the two segments.
Page 33 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration User Index Defines the currently generated user. For "Multi User MIMO > Active", only one user can be generated at a time. This parameter selects the generated one out of four avail- able users.
Page 34 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MCS on page 159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MCS Data Rate /Mbps Indicates the PPDU data rate. Remote command: on page 149 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:RATE? on page 156 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:RATE? Data Bits Per Symbol Displays the number of data bits sent by an OFDM symbol on all spatial streams.
Page 35 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Cod Rate Selects the coding rate. Remote command: on page 154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:RATE [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:RATE on page 154 Guard Selects which guard interval is used for the OFDM guard. For "Physical Mode > Green Field/Legacy", the field is read-only, since the modes have long guard intervals only.
Page 36: He Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration The data rates available are 1 Mbps, 2 Mbps, 5.5 Mbps, 11 Mbps and 22 Mbps. The 1 Mbps data rate is only available if the long PLCP format has been selected. The selection of the data rate also determines the possible modulation modes.
Page 37 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration 4. Select "PPDU > Conf...". The dialog provides settings to configure high efficiency (HE) frames, that are avail- able for WLAN standard IEEE 802.11ax. For settings that are shared by more IEEE 802.11 standards, see Chapter 3.4, "PPDU configuration", on page 30.
Page 38 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Link Direction Selects the link direction for HE/EHT frames. Remote command: on page 172 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:LINK Guard Selects which guard interval is used for the OFDM guard. For "Physical Mode > Green Field/Legacy", the field is read-only, since the modes have long guard intervals only.
Page 39 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration "EHT TRIG/HE TRIG" Requires "Link Direction > Uplink". Carries a single PSDU. It is sent as a response to a PPDU that con- tains a trigger frame. Remote command: on page 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat EHT-LTF Symb Duration/HE-LTF Symb Duration Selects the duration of the EHT/HE Long Training Field (LTF) symbol.
Page 40 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BMCS Preamble Puncturing Requires "Tx Mode > HE-80MHz/HE-80+80MHz" and "PPDU Format > HE MU". Enables preamble puncturing of the HE MU PPDU in 80 MHz or (80+80)/160 MHz channels.
Page 41 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BSSColor TXOP Duration If transmission opportunity (TXOP) is set to 127, it indicates no duration information. If it is set to any other value, it indicates duration information for network allocation vector (NAV) parameter and that the TXOP is protected.
Page 42 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Table 3-8: Bandwidth modes for HE-80MHz/HE-80+80MHz PPDUs Bandwidth HE channel Primary Secondary Secondary Secondary Secondary mode 20 MHz 20 MHz 40 MHz low 40 MHz high 80 MHz 80 MHz Unpunctured Punctured Unpunctured Unpunctured...
Page 43: Eht Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration When the 802.11 standard is active ("General > State > On"), the file is saved into the file path as specified in "Output File". Remote command: on page 173 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:LOGGing Output File Displays the fixed file path including the file name, in that the log file is saved.
Page 44 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration 2. Select the side tab "General > EHT General". This tab provides general settings to configure EHT frames. Settings: Max PE Duration......................44 Disambiguity......................44 Time Domain Windowing Active..................44 Transition Time......................44 Max PE Duration Selects the maximum packet extension (PE) duration.
Page 45 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration 3.4.3.2 U-SIG settings Access: 1. Select "PPDU > Conf... > General". 2. Select the side tab "U-SIG". This dialog provides additional settings to configure the Universal SIGNAL field. Settings: Link Direction........................ 45 PPDU Format........................45 Spatial Reuse...
Page 46 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration "EHT TRIG/HE TRIG" Requires "Link Direction > Uplink". Carries a single PSDU. It is sent as a response to a PPDU that con- tains a trigger frame. Remote command: on page 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat Spatial Reuse 1/2 Requires "PPDU Format >...
Page 47 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 172 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:EMCS 320MHz Type Sets the type of channelization of 320 MHz channels in the bandwidth (BW) field of the U-SIG-1 field. The channelization affects two adjacent 160 MHz channels of a 320 MHz channel in the 6 GHz band.
Page 48 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration pre-FEC Padding Factor Displays the pre forward error condition (FEC) padding factor used in the trigger PPDU. Remote command: on page 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFPFactor? PE Disambiguity Displays the disambiguity in the number of symbols occurring due to the packet exten- sion.
Page 49: User Configuration Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration 3.4.3.4 Logging Access: 1. Select "PPDU > Conf... > General". 2. Select the side tab "Logging". The tab provides settings to configure logging for EHT/HE frames. Settings: Logging State........................ 49 Output File........................49 Logging State If enabled, the contents of EHT/HE SIG fields and the payload are written into a file in...
Page 50 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Multiple users for 802.11ax Since multiple users are intended recipients in the OFDMA downlink, the AP needs to tell the STAs which resource unit belongs to them. In 802.11ax, the AP uses the HE SIG-B field in the HE_MU_PPDU for this purpose.
Page 51 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration The tab provides the settings for first and second content channel. Settings 1st/2nd Content Channel....................51 └ Selection....................51 └ Allocation....................51 └ Number of MU-MIMO users................51 └ Center 26-tone RU..................52 1st/2nd Content Channel Defines the settings of the common field and user-specific field of an EHT-SIG content channel or an HE-SIG-B content channel.
Page 52 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:MUNum<st> on page 177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:MUNum<st> Center 26-tone RU ← 1st/2nd Content Channel For HE frames. Requires "PPDU Format > HE MU/HE TRIG". For full bandwidth 80 MHz: if enabled, indicates that center 26 -tone RU is allocated in the common block fields of both SIGB content channels with same value.
Page 53 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Remote command: EHT[:SOURce<hw>]:BB:WLNN:FBLock<ch>:BEUL? on page 169 STA Id Sets the station ID, the 11 least significant bits of the association identifier (AID). Remote command: on page 179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STAid Nsts Sets the number of space time streams allocated to a particular user. If "Space time stream"...
Page 54: Data Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration MU MIMO Displays if the multi-user MIMO is used for current user. All MU-MIMO users share one resource unit (RU) using different space time streams. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:MUMimo:STATe? on page 178 Gain /dB Sets the additional gain that can be applied to the RU allocated by a particular user.
Page 55: Settings Data Length
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration 3.4.5.1 Data settings Access: 1. Select "Frame Blocks > PPDU > Config...". 2. Select "Data > Data Settings". The dialog comprises the settings for the configuration of the data. Settings Data Length........................55 Frame Duration......................
Page 56: Frame Duration
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration The maximum data length depends on the physical mode: ● In "Physical Mode > Legacy", the maximum value is 4061 bytes. ● In "Physical Mode > Mixed Mode" and "Physical Mode > Green Field", the maxi- mum value is 1048575 bytes.
Page 57: Bandwidth In Non Ht
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration "Preamble (available only for "Tx Mode > CCK/PBCC") Only" The scrambler is activated. Only the preamble is scrambled. Remote command: on page 164 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SCRambler:MODE [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:MODE on page 164 Ch. Bandwidth in Non HT (available only for "Tx Mode >...
Page 58: Duty Cycle
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration If the number of OFDM data symbols is changed, the generator calculates the data field length as a function of the set PPDU bit rate. This value is displayed at "Data Length".
Page 59: Service Field Clock Bit
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 PPDU configuration Service Field Clock Bit (available only for "Tx Mode > CCK/PBCC") Sets the locked clock bit in service field of the PLCP header. Via this flag (bit), the transmitter indicates whether transmission frequency and symbol rate have been derived from the same oscillator.
Page 60: A-Mpdu Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 A-MPDU settings Settings: Preamble/Header Active....................60 Smoothing........................60 Partial AID (hex)......................60 No TXOP PS......................... 60 Preamble/Header Active Activates preamble and signal fields of the frames in the current frame block. For "Type > Sounding", the preamble and signal field are always activated and cannot be deactivated.
Page 61 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 A-MPDU settings Access: 1. Select "IEEE 802.11... > Frame Blocks". 2. Select "Type > Data". 3. Select "Data > A-MPDU". 4. Select "DList/Pattern > Config". 5. Select "A-MPDU". The dialog comprises the A-MPDU settings. Settings: Number of MPDUs......................
Page 62: Mac Header And Fcs Configuration For Frame Block
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: on page 182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:SOURce [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:SOURce on page 182 DList / Pattern Depending on the selected data source, selects a data list or allows entering a user- defined bit pattern.
Page 63: Mac Header And Fcs
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Settings: ● MAC header and FCS.....................63 ● 802.11 MAC frame field...................63 ● Beacon settings.......................67 ● Trigger frame settings..................... 74 3.6.1 MAC header and FCS MAC Header Activates the generation of the MAC header for the PPDU.
Page 64 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: on page 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol on page 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PVERsion on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TYPE on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:SUBType on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TDS on page 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:FDS [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MFRagments on page 185...
Page 65 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block MAC Address Enters the value of the address field 1 to address field 4. The MAC header can contain up to four address fields, but not all must be available. Each of the 4 address fields can be activated or deactivated.
Page 66 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Example: An error-free transmission of 50 packets (no packet retransmission) is to be simulated. The sequence number is incremented by 1 for each packet. Since no packet is frag- mented, the fragment counter can always remain at 0.
Page 67: Beacon Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Increment Every ← Sequence Control Defines the number of packets required to increment the counter of the fragment bits or the sequence bits of the sequence control. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SCONtrol:FRAGment:INCRement on page 187...
Page 68 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 3.6.3.1 General beacon settings Access: 1. Select "IEEE 802.11 > Frame Blocks". 2. Select "Type > Beacon". 3. Select "PPDU > Config...". 4. Select "MAC Header & FCS > Beacon General". The dialog provides general beacon settings.
Page 69 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:BINTerval on page 203 SSID Specifies the desired service set identifier (SSID) or the wildcard SSID. The maximum allowed length is 32 characters. Remote command: on page 204 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:SSID...
Page 70 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 4. Select "MAC Header & FCS >Capability Info". The dialog displays the capability info parameters. The capability info parameters indicate, if requested optional capabilities and services are allowed, supported or in use.
Page 71 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Function If enabled this function indicates that: SCPI command name "Radio Mea- Radio measurement is supported (for example [:SOURce<hw>]:BB:WLNN: surement" requests, performs and reports radio measurements FBLock<ch>: in supported channels and provides information BFConfiguration:...
Page 72 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Function If enabled this function indicates that: SCPI command name "CF Pollable" The node can use the point coordination function [:SOURce<hw>]:BB:WLNN: (PCF), as opposed to the distributed coordination FBLock<ch>: function (DCF).
Page 73 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Settings: Parameters......................73 ERP Parameters Function If enabled this function indicates that: SCPI command name "Barker Pre- Associated stations have to use the long preamble (in [:SOURce<hw>]:BB:WLNN: amble Mode"...
Page 74: Trigger Frame Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block The dialog provides HT capability information. Settings: State..........................74 Green Field........................74 State Activates/ deactivates the HT capability information element. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:HTCapability: on page 210 STATe Green Field If enabled, the function indicates that the reception of PPDUs with HT Greenfield for-...
Page 75 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 4. Select "MAC Header & FCS > Common Info". This dialog provides common info field settings of the trigger frame settings. Settings: Trigger Frame Type.......................75 Trigger Type........................
Page 76: Length
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: on page 201 TTYPe? Length Specifies the value of the L-SIG length field. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LEN on page 201 Cascade Indication If set to 1, then there is a subsequent trigger frame. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: on page 200...
Page 77: Stbc
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: on page 201 MLTFmode Num HE-LTF Symbols Specifies the number of HE-LTF symbols present. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: on page 201 NHLSym STBC If set to 1, STBC encoding is used for the HE trigger-based PPDU response.
Page 78: He-Sig-A Reserved
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: on page 200 DOPPler HE-SIG-A Reserved Specifies the value of the reserved bits in the HE-SIG-A field. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: on page 201 HREServed Specifies the value of the reserved bits in the "Rsv"...
Page 79 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block MCS..........................79 DCM..........................80 Allocation.........................80 Target RSSI........................80 Rsv..........................80 Trigger Dependent User Info..................80 No. Of User Info Sets the number of "User Info" fields in the trigger frame. You can set up to 37 fields.
Page 80 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Specifies the dual carrier modulation. If the value is 0, then no DCM is used. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: on page 201 SS Allocation Specifies the spatial streams. This field contains 3 bits that specify the starting spatial stream and 3 bits that specify the number of spatial streams.
Page 81: Mac Header Ht/He And Vht Configuration
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration This dialog provides additional info settings of the trigger frame settings. Settings: MPDU EOF........................81 Min Trigger Process Time..................... 81 Padding Length......................81 MPDU EOF Selects the end of frame (EOF) tag. Tagged/untagged indication is set in the 1-bit EOF/Tag field of an MPDU.
Page 82 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration 2. Select "MAC Header & FCS > HT Config"/"MAC Header & FCS > VHT Con- fig"/"MAC Header & FCS > HE Config". Figure 3-1: MAC header: HT configuration Figure 3-2: MAC header: VHT configuration Figure 3-3: MAC header: HE configuration In this dialog, the mode, the time shifts and the transmit parameters can be config-...
Page 83: Common Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration 3.7.1 Common settings Provided are the following settings for enabling the "MAC HT/VHT Control Field": Control........................83 HT/VHT/HE Control.......................83 QoS Control Control field (2 bytes) with an embedded checkbox for activating the control mecha- nism of Quality of Service (QoS) data frames.
Page 84 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration Announcement..................... 84 Steering........................85 Reserved........................85 Calibration Sequence....................85 Calibration Position....................... 85 Link Adaption Control....................85 HT/VHT......................... 86 RDG/More PPDU The RDG/More signal field (LSB, 1 bit) issues the reverse direction grant. When trans- mitted by an initiator or a responder, this field is interpreted differently.
Page 85 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration CSI Steering Sets the position of the CSI feedback (2 bit) 00 = CSI 01 = uncompressed steering matrix 10 = compressed steering matrix 11 = reserved Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CSISteering on page 191...
Page 86: Mac Vht Configuration
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration 1 = request to the responder to transmit a sounding PPDU (Physical layer Protocol Data Unit). B2 (1bit) MRQ - MCS request 1 = request for feedback of MCS (Modulation Coding Scheme). B3-B5 (3bit) MRS - MRQ sequence identifier Set by sender to any value in the range '000'-'110' to identify MRQ.
Page 87 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration Settings: RDG/More PPDU......................87 Constraint........................87 Unsolicited MFB......................87 FB Tx Type........................87 Coding Type........................88 GID-H..........................88 MFB..........................88 MFSI/GID-L........................89 MSI..........................89 MRQ..........................89 Rsv..........................90 HT/VHT......................... 90 RDG/More PPDU The RDG/More signal field (LSB, 1 bit) issues the reverse direction grant.
Page 88 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration Unbeamformed VHT PPDU or transmit diversity using an STBC VHT PPDU. 1 = If the Unsolicited MFB subfield is set to 1 and the FB Tx Type subfield is set to 1, the unsolicited MFB refers to a beamformed SU-MIMO VHT PPDU.
Page 89 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration Subfield Meaning Definition Bandwidth of the recom- MFB = 1 mended MCS If the unsolicited MFB subfield is set to 1, the BW subfield con- tains the bandwidth of which the recommended MCS is intended for (Link adaption using the VHT format of the "HT Control"...
Page 90: Mac He Control Field Settings
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 MAC header HT/HE and VHT configuration This signal field (1 bit) is defined, but not used. It is set to zero by the transmitter and ignored by the receiver. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:VREServed on page 199 HT/VHT The subfield indicates the used format (HT or VHT).
Page 91: Spatial Mapping
® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Spatial mapping Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:HEControl: on page 199 ACONtrol Indicates the use of the HE format, if "HT/VHT" is set to 1. 0 = indicates use of the VHT format. 1 = indicates use of the HE format. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:HEControl: on page 199...
Page 92 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Spatial mapping 2. Select "Spatial Mapping". The dialog provides settings to configure the spatial mapping mode, the time shifts and the transmit parameters. The WLAN standard IEEE 802.11 builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output).
Page 93 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Spatial mapping Mode Selects the spatial mapping mode for the selected frame block. The matrix element values are loaded using Info Class Methods. "Off" (available only for "Physical Mode > Legacy" frame) The spatial mapping mode is switched off automatically. "Direct"...
Page 94 ® WLAN configuration and settings R&S SMW-K54/-K86/-K142/-K147 Spatial mapping Q (Transmit Matrix) Displays the time shift value of element Q of the selected row and column of the spatial transmit matrix. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:ROW<st>:COL<dir>:Q? on page 212 User Manual 1175.6749.02 ─ 27...
Page 95: How To Work With The Ieee 802.11 Wlan Option
® How to work with the IEEE 802.11 WLAN option R&S SMW-K54/-K86/-K142/-K147 Generating a 160 MHz 2x2 WLAN 802.11ax signal 4 How to work with the IEEE 802.11 WLAN option The R&S SMW equipped with the option digital standard IEEE 802.11 WLAN allows you to generate signals for different transmitter and receiver tests scenarios.
Page 96: Generating A 3X3 Mimo Wlan 802.11N Signal With A R&S Smw For Transmitter Tests
® How to work with the IEEE 802.11 WLAN option R&S SMW-K54/-K86/-K142/-K147 Generating a 3x3 MIMO WLAN 802.11n signal with a R&S SMW for transmitter tests 6. Set "IEEE 802.11 WLAN > General > Transmission Bandwith > 160 MHz". 7. Set the frame block in the "IEEE 802.11 WLAN > Frame Block Configuration" dia- log: a) Set "Std.>...
Page 97 ® How to work with the IEEE 802.11 WLAN option R&S SMW-K54/-K86/-K142/-K147 Generating a 3x3 MIMO WLAN 802.11n signal with a R&S SMW for transmitter tests ● Optional, option AWGN (R&S SMW-K62) The instruments have to be configured and connected as described in the following section.
Page 98 ® How to work with the IEEE 802.11 WLAN option R&S SMW-K54/-K86/-K142/-K147 Generating a 3x3 MIMO WLAN 802.11n signal with a R&S SMW for transmitter tests Select "External Reference Frequency Source" and configure the "Synchronization Bandwidth" and the "External Reference Frequency" accordingly. For a detailed description of how to do that, refer to the R&S SMW user manual.
Page 99: Generating A Realistic Mxn Mimo Wlan 802.11N/Ac/P Signal For Receiver Test Under Static Conditions
® How to work with the IEEE 802.11 WLAN option R&S SMW-K54/-K86/-K142/-K147 Generating a realistic MxN MIMO WLAN 802.11n/ac/p signal for receiver test under static conditions 4.3 Generating a realistic MxN MIMO WLAN 802.11n/ac/p signal for receiver test under static conditions This example shows you how to enable the R&S SMW to generate a WLAN 802.11n/ 802.11ac/802.11p signal for simple diversity and simulation of frequency flat MIMO channel conditions.
Page 100 ® How to work with the IEEE 802.11 WLAN option R&S SMW-K54/-K86/-K142/-K147 Generating a realistic MxN MIMO WLAN 802.11n/ac/p signal for receiver test under static conditions 4. In the "Transmit Antenna Setup" dialog, select the number of "Tx Antennas" to be simulated.
Page 101: Generating A Realistic Mxn Mimo Wlan 802.11N/Ac/P Signal For Receiver Test Under Real Word Conditions
® How to work with the IEEE 802.11 WLAN option R&S SMW-K54/-K86/-K142/-K147 Generating a realistic MxN MIMO WLAN 802.11n/ac/p signal for receiver test under real word conditions 1, 2, 3 = Transmission antennas Tx1 to Tx3 4, 5, 6 = Weigthing factors w1 to w3 = Baseband output for receiving antenna Rx1 8.
Page 102: Signal Control And Signal Characteristics
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings 5 Signal control and signal characteristics This section lists settings provided for configuring the baseband filter, for defining the signal generation start and for generating signals necessary for synchronization with other instruments.
Page 103 ® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings Settings Use Default Wlan Filter....................103 Filter..........................103 Roll Off Factor or BxT....................103 Cut Off Frequency Factor....................104 Cut Off Frequency Shift....................104 Sample Rate Variation....................104 IFFT Upsampling......................104 Use Default Wlan Filter Requires "Transmission Bandwidth >...
Page 104 ® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings Cut Off Frequency Factor Sets the value for the cutoff frequency factor. The cutoff frequency of the filter can be adjusted to reach spectrum mask requirements. Remote command: on page 128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASs on page 128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASSEVM...
Page 105: Clipping Settings
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings Remote command: on page 127 [:SOURce<hw>]:BB:WLNN:FILTer:IUPSampling 5.1.2 Clipping settings Access: ► Select "Filter/Clipping Settings > Clipping". The dialog comprises the settings, necessary to configure the clipping. Settings Clipping State......................105 Clipping Level......................106 Clipping Mode......................
Page 106: Trigger Settings
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Trigger settings Since clipping the signal not only changes the peak value but also the average value, the effect on the crest factor is unpredictable. The following table shows the effect of the "Clipping"...
Page 107: Trigger Settings Common To All Basebands
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Trigger settings This tab provides access to the settings necessary to select and configure the trig- ger and to arm or trigger an internal trigger manually. The current signal generation status is displayed in the header of the tab together with information on the enabled trigger mode.
Page 108: Trigger Mode
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Trigger settings You can access and configure the common trigger source and trigger mode settings in any of the basebands. An arm or a restart trigger event applies to all basebands, too. You can still apply different delay to each of the triggers individually.
Page 109: Arm
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Trigger settings ● "Stopped" The signal is not generated and the instrument waits for a trigger event. Remote command: on page 133 [:SOURce<hw>]:BB:WLNN:TRIGger:RMODe? Stops the signal generation until subsequent trigger event occurs. Remote command: on page 132 [:SOURce<hw>]:BB:WLNN:TRIGger:ARM:EXECute...
Page 110: External Trigger Inhibit
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Trigger settings The signal calculation starts simultaneously with the trigger event. Because of the processing time of the instrument, the first samples are cut off and no signal is out- put. After elapsing of the internal processing time, the output signal is synchronous to the trigger event.
Page 111: Marker Settings
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Marker settings Trigger Delay Delays the trigger event of the signal from: ● The external trigger source ● The other path ● The other basebands (internal trigger), if common trigger settings are used. Use this setting to: ●...
Page 112 ® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Marker settings Settings Marker Mode....................... 112 Marker x Delay......................115 Marker Mode Marker configuration for up to 3 markers. The settings are used to select the marker mode defining the shape and periodicity of the markers. The contents of the dialog change with the selected marker mode.
Page 113 ® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Marker settings "Frame Active Part / Frame Inactive Part" A marker signal is generated to mark every active part of each frame. The active data transfer part (PPDU) of a frame period is marked with high, the inactive part (idle time) with low.
Page 114 ® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Marker settings decrease the carrier leakage during inactive signal parts by feeding it into the pulse modulator. Otherwise, the frame block and frame index are entered and the active part of the specific frame is masked. The parameters "Rising Edge Shift / Falling Edge Shift"...
Page 115: Clock Settings
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Clock settings "Pulse" A regular marker signal is generated. The clock frequency is defined by entering a divider. The frequency is derived by dividing the chip rate by the divider. The input box for the divider opens when "Pulse" is selected, and the resulting pulse frequency is displayed below it.
Page 116 ® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Clock settings This tab provides access to the settings necessary to select and configure the clock signal, like the clock source and clock mode. This section focuses on the available settings. For information on how these settings affect the signal, refer to section "Basics on ..." in the R&S SMW user manual.
Page 117: Local And Global Connectors Settings
® Signal control and signal characteristics R&S SMW-K54/-K86/-K142/-K147 Local and global connectors settings Measured External Clock Provided for permanent monitoring of the enabled and externally supplied clock signal. Remote command: CLOCk:INPut:FREQuency? 5.5 Local and global connectors settings Each of the "Trigger In", "Marker" and "Clock" dialogs and the "Trigger Marker Clock" dialog provides a quick access to the related connector settings.
Page 118: Remote-Control Commands
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 6 Remote-control commands The following commands are required to perform signal generation with the IEEE 802.11 WLAN options in a remote environment. We assume that the R&S SMW has already been set up for remote operation in a network as described in the R&S SMW documentation.
Page 119: Programming Examples
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Programming examples ● Programming examples..................119 ● General commands....................122 ● Filter/clipping settings....................125 ● Trigger settings..................... 131 ● Marker settings......................137 ● Clock settings......................141 ● Antenna configuration settings................142 ● Frame block configuration..................145 ● Frame configuration settings.................152 6.1 Programming examples The following sections provide programming examples for the IEEE 802.11 Wlan options.
Page 120 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Programming examples SOURce1:BB:WLNN:TRIGger:SOURce INTB SOURce1:BB:WLNN:TRIGger:OBASeband:INHibit 10 SOURce1:BB:WLNN:TRIGger:DELay:UNIT SAMP SOURce1:BB:WLNN:TRIGger:OBASeband:DELay 25 / ****************************************************************** // Alternatively set and query delay in seconds. // ****************************************************************** SOURce1:BB:WLNN:TRIGger:DELay:UNIT TIME SOURce1:BB:WLNN:TRIGger:OBASeband:TDELay 0.00001 SOURce1:BB:WLNN:TRIGger:OBASeband:RDELay? ****************************************************************** // Alternatively configure trigger in armed retrigger mode, use // external global trigger.
Page 121: Marker Settings
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Programming examples SOURce1:BB:WLNN:TRIGger:EXEcute SOURce1:BB:WLNN:TRIGger:ARM:EXECute SOURce1:BB:WLNN:TRIGger:EXEcute // ****************************************************************** // Query trigger signal generation status. // ****************************************************************** SOURce1:BB:WLNN:TRIGger:RMODe? 6.1.2 Marker settings Example: Marker configuration // ****************************************************************** // Query marker mode, set rising and falling offsets. // ****************************************************************** SOURce:BB:WLNN:TRIGger:OUTPut2:MODE? // RESTart SOURce:BB:WLNN:TRIGger:OUTPut2:FOFFset 10...
Page 122: General Commands
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 General commands 6.2 General commands ..................122 [:SOURce<hw>]:BB:WLNN:BWidth .................122 [:SOURce<hw>]:BB:WLNN:PRESet ..............122 [:SOURce<hw>]:BB:WLNN:SETTing:CATalog? ..............123 [:SOURce<hw>]:BB:WLNN:SETTing:DELete ..............123 [:SOURce<hw>]:BB:WLNN:SETTing:LOAD ..............123 [:SOURce<hw>]:BB:WLNN:SETTing:STORe ................... 124 [:SOURce<hw>]:BB:WLNN:STATe ................124 [:SOURce<hw>]:BB:WLNN:VERSion? ..............124 [:SOURce<hw>]:BB:WLNN:WAVeform:CREate [:SOURce<hw>]:BB:WLNN:BWidth <BWidth> The command selects the transmission bandwidth. Whenever the bandwidth changes from a higher to a lower one, the frame blocks are validated because some of them could be invalid in the lower bandwidth (invalid TX Mode).
Page 123 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 General commands Example: MMEM:CDIR '/var/user/temp/wlann' Sets the default directory to /var/user/temp/wlann. BB:WLNN:SETT:CAT? Reads out all the files with IEEE 802.11 settings in the default directory. Response: 'wlann_1','wlann_2' The files ''wlann1' and 'wlann2'' are available. Usage: Query only Manual operation: "Save/Recall"...
Page 124 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 General commands Setting parameters: <Filename> string Example: :SOURce1:BB:WLNN:SETT:STOR 'wlann_1' Saves the current settings into file 'wlann_1'. Usage: Setting only Manual operation: "Save/Recall" on page 19 [:SOURce<hw>]:BB:WLNN:STATe <State> Activates the standard and deactivates all the other digital standards and digital modu- lation modes in the same path.
Page 125: Filter/Clipping Settings
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings 6.3 Filter/clipping settings ..............125 [:SOURce<hw>]:BB:WLNN:CLIPping:LEVel ..............125 [:SOURce<hw>]:BB:WLNN:CLIPping:MODE ..............126 [:SOURce<hw>]:BB:WLNN:CLIPping:SPPState ..............126 [:SOURce<hw>]:BB:WLNN:CLIPping:STATe ............126 [:SOURce<hw>]:BB:WLNN:FILTer:DEFSetting:STATe ..............127 [:SOURce<hw>]:BB:WLNN:FILTer:IUPSampling ............ 127 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:APCO25 ............127 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:COSine ..........127 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:COSine:COFS ............128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:GAUSs ............128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASs ..........128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASSEVM ............. 129 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:PGAuss ...........
Page 126 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings SCALar The reference level is the absolute maximum of the I and Q val- ues. *RST: VECTor Example: BB:WLNN:CLIP:MODE SCAL Selects the absolute maximum of all the I and Q values as the reference level.
Page 127 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings Example: SOURce1:BB:WLNN:FILTer:DEFSetting:STATe 1 Activates the WLAN default filter settings. Manual operation: "Use Default Wlan Filter" on page 103 [:SOURce<hw>]:BB:WLNN:FILTer:IUPSampling <IFFTUpsampling> Activates inverted Fast Fourier Transformation (IFFT) upsampling. Parameters: <IFFTUpsampling> 1 | ON | 0 | OFF *RST: Example: SOURce1:BB:WLNN:FILTer:IUPSampling ON...
Page 128 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings Parameters: <CoFs> float Range: -1 to 1 Increment: 0.01 *RST: Example: BB:WLNN:FILT:PAR:COS:COFS 0.04 the "cut of frequency shift" value is set to 0.04. Manual operation: "Cut Off Frequency Shift" on page 104 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:GAUSs <Gauss> Sets the roll-off factor for the Gauss filter type.
Page 129 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings Example: BB:WLNN:FILT:PAR:LPASSEVM 0.5 The cut of frequency factor is set to 0.5. Manual operation: "Cut Off Frequency Factor" on page 104 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:PGAuss <PGauss> Sets the roll-off factor for the pure gauss filter type. Parameters: <PGauss>...
Page 130 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Filter/clipping settings [:SOURce<hw>]:BB:WLNN:FILTer:TYPE <Type> The command selects the filter type. Parameters: <Type> RCOSine | COSine | GAUSs | LGAuss | CONE | COF705 | COEQualizer | COFequalizer | C2K3x | APCO25 | SPHase | RECTangle | PGAuss | LPASs | DIRac | ENPShape | EWPShape | LPASSEVM *RST: Depends on layer mode...
Page 131: Trigger Settings
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Trigger settings 6.4 Trigger settings Example: Configure and enable triggering SOURce1:BB:WLNN:TRIGger:SEQuence SINGle SOURce1:BB:WLNN:TRIGger:SLENgth 200 // the first 200 samples of the current waveform will be output after // the next trigger event SOURce1:BB:WLNN:TRIGger:SOURce INTB // the internal trigger signal from the other path must be used SOURce1:BB:WLNN:TRIGger:OBASeband:DELay 25 SOURce1:BB:WLNN:TRIGger:OBASeband:INHibit 10 SOURce1:BB:WLNN:TRIGger:SOURce INT...
Page 132 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Trigger settings ..............133 [:SOURce<hw>]:BB:WLNN:TRIGger:RMODe? ..............134 [:SOURce<hw>]:BB:WLNN:TRIGger:SLENgth ..............134 [:SOURce<hw>]:BB:WLNN:TRIGger:SLUNit ..............135 [:SOURce<hw>]:BB:WLNN:TRIGger:SOURce ............. 135 [:SOURce<hw>]:BB:WLNN:TRIGger[:EXTernal]:DELay ............. 136 [:SOURce<hw>]:BB:WLNN:TRIGger[:EXTernal]:INHibit ..............136 [:SOURce<hw>]:BB:WLNN[:TRIGger]:SEQuence [:SOURce<hw>]:BB:WLNN:TRIGger:ARM:EXECute Stops signal generation for trigger modes armed auto and armed retrigger. A subse- quent internal or external trigger event restart signal generation.
Page 133 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Trigger settings [:SOURce<hw>]:BB:WLNN:TRIGger:OBASeband:DELay <Delay> Specifies the trigger delay (expressed as a number of samples) for triggering by the trigger signal from the second path. Parameters: <Delay> float Range: 0 to 2147483647 Increment: 0.01 *RST: Example: BB:WLNN:TRIG:SOUR INTB The internal trigger signal from the other path must be used BB:WLNN:TRIG:INH 200...
Page 134 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Trigger settings Example: BB:WLNN:TRIG:SOUR EGT1 sets external triggering. BB:WLNN:TRIG:MODE ARET selects the Armed_Retrigger mode. BB:WLNN:TRIG:RMOD? queries the current status of signal generation. Response: RUN the signal is generated, an external trigger was executed. Usage: Query only Manual operation: "Running/Stopped"...
Page 135 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Trigger settings Example: BB:WLNN:SEQ SING Sets trigger mode single. BB:WLNN:TRIG:SLUN SEQ Sets unit sequence for the entry of sequence length. BB:WLNN:TRIG:SLEN 2 Sets a sequence length of 2 sequences. Two sequences will be output after the next trigger event. Manual operation: "Signal Duration Unit"...
Page 136 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Trigger settings Parameters: <Delay> float Range: 0 to 2147483647 Increment: 0.01 *RST: Default unit: samples Example: Example"Configure and enable triggering" on page 131. Manual operation: "Trigger Delay" on page 111 [:SOURce<hw>]:BB:WLNN:TRIGger[:EXTernal]:INHibit <Inhibit> Specifies the number of samples by which a restart is to be inhibited following an exter- nal trigger event.
Page 137: Marker Settings
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Marker settings 6.5 Marker settings ..........137 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:MODE ..........138 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:ONTime ..........138 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:OFFTime ..........138 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FBINdex ..........139 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FINDex ..........139 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FESHift ..........139 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:RESHift ..........140 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:PATTern ........140 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:PULSe:DIVider ......140 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:PULSe:FREQuency? ..........141 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:DELay [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:MODE <Mode> Defines the signal for the selected marker output.
Page 138 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Marker settings PULSe A pulsed marker signal is generated. The pulse frequency (= symbol rate/divider) is defined with the SOUR:BB:WLNN:TRIG:OUTP:PULSe:DIVider command and can be queried with the SOUR:BB:WLNN:TRIG:OUTP:PULSe:FREQuency? command. RATio A marker signal corresponding to the Time Off / Time On specifi- cations in the commands SOURce:BB:WLNN:TRIGger:OUTPut:OFFT and "SOURce:BB:WLNN:TRIGger:OUTPut:ONT"...
Page 139 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Marker settings Manual operation: "Marker Mode" on page 112 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FINDex <FIndex> Sets the frame index, that is, the frame to be marked in the frame block marked with [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FBINdex. The maximum value depends on the number of frames set with command [:SOURce<hw>]:BB:WLNN: .
Page 140 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Marker settings [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:PATTern <Pattern> Defines the bit pattern used to generate the marker signal if [:SOURce<hw>]:BB: WLNN:TRIGger:OUTPut<ch>:MODEis set to PATTern. Parameters: <Pattern> 64 bits 0 = marker off, 1 = marker on *RST: #H2,2 Example: BB:WLNN:TRIG:OUTP2:PATT #B000000011111111,15 Sets a bit pattern.
Page 141: Clock Settings
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Clock settings Example: BB:WLNN:TRIG:OUTP:PULS:DIV 2 Sets the divider marker signal of the corresponding marker sig- nal to the value 2. BB:WLNN:TRIG:OUTP:MODE PULS Enables the pulsed marker signal. BB:WLNN:TRIG:OUTP:PULS:FREQ? Queries the pulse frequency of the marker signal. Response: 33 000 The resulting pulse frequency is 33 kHz.
Page 142: Antenna Configuration Settings
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Antenna configuration settings [:SOURce<hw>]:BB:WLNN:CLOCk:SOURce <Source> Selects the clock source. Parameters: <Source> INTernal|ELCLock|EXTernal *RST: INTernal Example: BB:WLNN:CLOC:SOUR INT Selects an internal clock reference. Options: ELCLock requires R&S SMW-B10 Manual operation: "Clock Source" on page 116 6.7 Antenna configuration settings ..............142 [:SOURce<hw>]:BB:WLNN:ANTenna:CMODe? ..............
Page 143 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Antenna configuration settings Manual operation: "Antennas" on page 21 [:SOURce<hw>]:BB:WLNN:ANTenna:NOBB? Queries the number of basebands required for the transmit antenna setup. Return values: <NOBB> NBB1 | NBB2 | NBB4 | NBB3 | NBB8 *RST: NBB1 Usage: Query only [:SOURce<hw>]:BB:WLNN:ANTenna:SYSTem <System>...
Page 144 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Antenna configuration settings [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:OUTPut:FSELect <FSelect> The command saves the IQ chain in a file. Parameters: <FSelect> string Example: BB:WLNN:ANT:TCH1:OUTP:FSEL '/var/user/temp/wlnn_1.wv' saves the IQ chain in the selected file. Manual operation: "Output" on page 22 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:REAL <Real> Sets the value for the Real coordinate.
Page 145: Frame Block Configuration
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Parameters: <Phase> float Range: 0 to 359.99 Increment: 0.01 *RST: Example: :BB:WLNN:ANT:TCH1:TX1:PHAS 10 Sets the phase to 10°. Manual operation: "Imaginary/Phase" on page 22 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:MAGNitude <Magnitude> Sets the magnitude when cylindrical mapping coordinates are selected. Parameters: <Magnitude>...
Page 146 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame block configuration ..............151 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:STATe ..............151 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:TMODe ..............151 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:TYPE [:SOURce<hw>]:BB:WLNN:FBLock:APPend Appends a frame block to the end of the frame blocks list. Example: BB:WLNN:FBL:APP Usage: Event Manual operation: "Append" on page 29 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:COPY [:SOURce<hw>]:BB:WLNN:CFBLock <CfBlock> Copies the selected frame block.
Page 147 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame block configuration [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PASTe [:SOURce<hw>]:BB:WLNN:PFBLock <PfBlock> Pastes the selected frame block. Setting parameters: <PfBlock> integer Range: 1 to 99 Example: BB:WLNN:PFBL 20 pastes the frame block to row 20. Usage: Setting only [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BCSMoothing <BCSmoothing> Activates beam change and smoothing. Parameters: <BCSmoothing>...
Page 148 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Parameters: <FCount> integer Range: 1 to 20 000 Increment: 1 *RST: Example: BB:WLNN:FBL5:FCO 1 Sets the number of transmitted frames in the current frame block to 1. Manual operation: "Frames" on page 28 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA <Data>...
Page 149 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Parameters: <DSelection> string Example: BB:WLNN:FBL5:DATA DLIS Selects the data lists data source. MMEM:CDIR '/var/user/temp/Lists_DM' Selects the directory for the data lists. BB:WLNN:FBL5:DATA:DSEL 'dlist1' Selects file 'dlist1' as the data source. This file must be in the directory /var/user/temp/Lists_DM and have the file exten- sion *.dm_iqd.
Page 150 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Example: BB:WLNN:FBL5:ITIMe 0.0025 sets the idle time to 2.5 msec. Manual operation: "Idle Time /ms" on page 28 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PMODe <PMode> Selects the preamble design. For physical type SOUNDING, only GREEN FIELD is available. Parameters: <PMode>...
Page 151 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame block configuration Example: :SOURce1:BB:WLNN:FBL1:STAN WN Sets the IEEE 802.11n standard Manual operation: "Std." on page 23 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:STATe <State> Enables the corresponding frame block for transmission. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL5:STAT ON...
Page 152: Frame Configuration Settings
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL5:TYPE DATA sets the PPDU type data. Manual operation: "Type" on page 24 6.9 Frame configuration settings ● Frame block PPDU configuration................152 ● EHT/HE configuration................... 168 ● User configuration....................176 ● MPDU configuration....................
Page 153 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings ............. 160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MU<st0>:GID ...........160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MU<st0>:NSTS ..............160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:NTPS .............161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PAID:PATTern ............161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PLCP:FORMat ..........161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PLCP:LCBit:STATe ..........162 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PREamble:STATe ........... 162 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:PNSeed ............. 162 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PSDU:BRATe ........163 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PSDU:BSPReading:STATe ..........163 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PSDU:MODulation? ......164 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:MODE ..........164 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SCRambler:MODE ......165 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:PATTern ...........
Page 154 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:ENCoder? [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:ENCoder? Queries the number of encoders to be used. This value depends on the data rate. For data rate ≤ 300 Mps, this value is 1. Otherwise the number of encoders is 2. Return values: <Encoder>...
Page 155 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:BPSymbol? [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:BPSymbol? Queries the number of data bits sent by an OFDM symbol on all spatial streams. Return values: <BpSymbol> integer *RST: Example: BB:WLNN:FBL5:DATA:BPS? queries the number of data bits sent by an OFDM symbol on all spatial streams.
Page 156 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:FDURation? Queries the duration of the frame in milliseconds, i.e. the WLAN burst length. Frame duration and duty cycle are related to data length and number of data symbols. Whenever one of them changes, the frame duration and duty cycle are updated. Return values: <FrameDuration>...
Page 157 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL5:DATA:RATE? queries the data rate. Usage: Query only Manual operation: "Data Rate /Mbps" on page 29 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:SYMBols <Symbols> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:SYMBols <Symbols> Sets the number of data symbols per frame block. If the number of OFDM data symbols is changed, the generator calculates the data field length as a function of the set PPDU bit rate and displays it at Data Length.
Page 158 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <DefaultPNSeed> 1 | ON | 0 | OFF *RST: Example: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]: on page 162. PNSeed Manual operation: "Default PN Seed" on page 57 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:ESSTream <EsStream> Sets the value of the extended spatial streams. This field is active for frame block type sounding only to probe additional dimensions to the channel.
Page 159 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL5:ILE:STAT ON activates the interleaver. Manual operation: "Interleaver Active" on page 57 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MCS <MCS> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MCS <MCS> Selects the modulation and coding scheme for the spatial streams. Parameters: <MCS> MCS0 | MCS1 | MCS2 | MCS3 | MCS4 | MCS5 | MCS6 | MCS7 | MCS8 | MCS9 | MCS10 | MCS11 | MCS12 | MCS13 | MCS14 | MCS15 | MCS16 | MCS17 | MCS18 | MCS19 | MCS20 | MCS21 | MCS22 | MCS23 | MCS24 | MCS25 | MCS26 |...
Page 160 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <MUMimo> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:BB:WLNN:FBL1:MUM:STAT ON activates Multi User MIMO. Manual operation: "Multi User MIMO" on page 31 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MU<st0>:GID <GID> Sets the group ID for all available users. Parameters: <GID>...
Page 161 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings *RST: BB:WLNN:FBL1:NTPS ON Example: Activates NTPS. Manual operation: "No TXOP PS" on page 60 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PAID:PATTern <Pattern> (avaliable only for VHT Tx mode) The command provides an abbreviated indication of the intended recipient(s) of the frame.
Page 162 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <State> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL5:PMOD LEG sets the physical mode to LEGACY. BB:WLNN:FBL5:TMOD CCK sets the transport mode BB:WLNN:FBL5:PLCP:LCB:STAT OFF sets the Locked Clock Bit Manual operation: "Service Field Clock Bit"...
Page 163 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Sets the PSDU bit rate. Parameters: <BRate> integer Range: 0 to 22E6 *RST: 11E6 Example: BB:WLNN:FBL5:PMOD LEG sets the physical mode to LEGACY BB:WLNN:FBL5:TMOD CCK sets the transport mode BB:WLNN:FBL5:PSDU:BRAT 2E6 sets the PSDU bit rate of 2 Mbps Manual operation: "PSDU Bit Rate"...
Page 164 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL5:PMOD LEG Sets the physical mode to legacy. BB:WLNN:FBL5:TMOD CCK Sets the transport mode to CCK. BB:WLNN:FBL5:PSDU:BRAT P2MBPS Sets the PSDU bit rate to 2 mbps. BB:WLNN:PSDU:MOD? Queries the modulation mode. Response: "DQPSK"...
Page 165 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:PATTern <Pattern> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SCRambler:PATTern <Pattern> The command sets the initialization value for scrambling mode User. This value is then identical in each generated frame. Parameters: <Pattern> 8 bits *RST: #H01,8 Example: BB:WLNN:FBL5:SCR:PATT #H3F,8 sets the user defined initialization value for the scrambler.
Page 166 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL5:SERV:PATT #H3F,16 sets the value for the service field. Manual operation: "Service Field (hex)" on page 58 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMOothing <SMOothing> (available for all Tx modes, except VHT) This command indicates to the receiver whether frequency-domain smoothing is rec- ommended as part of channel estimation.
Page 167 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Usage: Query only Manual operation: "Space Time Block Coding" on page 32 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:STSTream <Ststream> Sets the number of the space time streams. This value depends on the number of spa- tial streams defined with command SOURce:BB:WLNN:FBLock:SSTReam. Changing the number of the Spatial Streams immediately changes the value of the Space Time Streams to the same value.
Page 168: Eht/He Configuration
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:UINDex <UIND> Defines the currently generated user. In activated Multi User MIMO only, one user can be generated at a time. This parameter selects the generated one out of four available users. Parameters: <UIND>...
Page 169 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: :BB:WLNN:FBL1 BCHG ON Enables that the beam is changed between the pre-HE and HE modulated fields. Manual operation: "Beam Change" on page 38 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BDCM <SIGBDCM> Enables the use of dual carrier modulation (DCM) in a signal B field. Parameters: <SIGBDCM>...
Page 170 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: :BB:WLNN:FBL1:BMCS MCS1 Sets the SIG-B MCSs to modulation scheme 1. Manual operation: "SIG-B MCS" on page 39 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BSSColor <BSSColor> Sets the BSS color, an identifier of the basic service sets (BSS) field. This parameter helps to check if a detected frame is coming form an overlapping station.
Page 171 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <RuAllocation> RU0 | RU1 | RU2 | RU3 | RU4 | RU5 | RU6 | RU7 | RU8 | RU9 | RU10 | RU11 | RU12 | RU13 | RU14 | RU15 | RU16 | RU17 | RU18 | RU19 | RU20 | RU21 | RU22 | RU23 | RU24 | RU25 | RU26 | RU27 | RU28 | RU29 | RU30 | RU31 | RU32 | RU33 | RU34 | RU35 | RU36 | RU37 | RU38 | RU39 | RU40 | RU41 |...
Page 172 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DOPPler <DOPPLER> If switched on, the Doppler effect is used for the PPDU. Parameters: <DOPPLER> OFF | ON | 1 | 0 Example: :BB:WLNN:FBLock1:DOPP ON Enables the Doppler effect to be used for the PPDU. Manual operation: "Doppler"...
Page 173 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:LOGFile? Queries the fixed file path used for logging the contents of HE-SIG-A and HE-SIG-B fields, if is set to ON. [:SOURce<hw>]:BB:WLNN:FBLock<ch>:LOGGing Return values: <LogFile> string Usage: Query only Manual operation: "Output File" on page 43 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:LOGGing <LoggingState>...
Page 174 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PED? Queries the disambiguity in the number of sybmbols occuring due to the packet exten- sion. Return values: <PEDisambiguity> integer Range: 0 to 1 *RST: Usage: Query only Manual operation: "PE Disambiguity" on page 41 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat <PpduFormat>...
Page 175 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Return values: <PreFECPadding> integer Range: 0 to 3 *RST: Usage: Query only Manual operation: "pre-FEC Padding Factor" on page 41 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PPUNcturing:BW <PreamblePuncBw> Sets the bandwidth mode of preamble puncturing. Parameters: <PreamblePuncBw> 4 | 5 | 6 | 7 Sets the bandwidth mode for HE80 channels.
Page 176: User Configuration
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: SOURce1:BB:WLNN:FBLock1:SPAReuse1 0 // Spatial reuse is not allowed for frame block 1. SOURce1:BB:WLNN:FBLock1:SPAReuse1 1 // Spatial reuse is not allowed for frame block 1. Manual operation: "Spatial Reuse 1/2" on page 41 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SYMDuration <HeLtfSymDur>...
Page 177 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:RUSelection<st> <RuSelCh1> For HE frames. Sets the resource unit allocation of the first content channel for the respective channel and station. Parameters: <RuSelCh1> RU0 | RU1 | RU2 | RU3 | RU4 | RU5 | RU6 | RU7 | RU8 | RU9 | RU10 | RU11 | RU12 | RU13 | RU14 | RU15 | RU18 | RU19 | RU20 | RU21 | RU22 | RU23 | RU24 | RU25 | RU34 | RU35 | RU36 | RU37 | RU38 | RU16 | RU17 | RU26 | RU27 | RU28 |...
Page 178 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <MuNumCh1> integer Range: 0 to 8 *RST: Manual operation: "Number of MU-MIMO users" on page 51 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CENRu<st> <Center26toneRU> For full bandwidth 80 MHz: if enabled, indicates that center 26 -tone RU is allocated in the common block fields of both SIGB content channels with same value.
Page 179 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Usage: Query only Manual operation: "MU MIMO" on page 54 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:NSTS <UserNsts> Sets the number of spatial streams, the number of space time streams minus 1. Parameters: <UserNsts> integer Range: 1 to 8 *RST: Manual operation: "Nsts"...
Page 180: Mpdu Configuration
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <UserState> 1 | ON | 0 | OFF *RST: Manual operation: "State" on page 54 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:TXBF <TXBF> If switched on, indicates that the beamforming matrix is applied to the waveform. Parameters: <TXBF>...
Page 181 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings The lists are saved as files with the fixed file extensions *.dm_iqd in a directory of the user's choice. Parameters: <Filename> string Example: BB:WLNN:FBL1:MPDU1:DATA DLIS Selects the Data Lists data source. MMEM:CDIR '/var/user/temp/Lists' Selects the directory for the data lists.
Page 182: Mac Header Configuration
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:SOURce <Source> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:SOURce <Source> Selects the data source. Parameters: <Source> ZERO | ONE | PATTern | PN9 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt PNxx The pseudo-random sequence generator is used as the data source.
Page 183 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings ........... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol ......185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:FDS ..........185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:FDS ...... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:MDATa ........185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MDATa ..... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:MFRagments ....... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MFRagments ...... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:ORDer ........185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:ORDer ...185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:PMANagement ......185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PMANagement ....185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:PVERsion ........185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PVERsion...
Page 184 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:ADDRess<st> <Address> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:ADDRess<st> <Address> The command enters the value of the address fields 1 ... 4. Exactly 48 bits must be entered. Each address is 6 bytes (48 bit) long. The addresses can be entered in hexa- decimal form in the entry field of each address field.
Page 185 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:BSSid <Bssid> Sets the value of the basic service set identification (BSSID) field. Parameters: <Bssid> integer Example: BB:WLNN:FBL1:MAC:BSS #H124836C7EA54,48 Sets the value of the BSSID field to 124836C7EA54 Manual operation: "BSSID (hex)" on page 65 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol <FControl>...
Page 186 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:RETRy <Retry> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:SUBType <Subtype> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:SUBType <Subtype> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:TDS <Tds> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TDS <Tds> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:TYPE <Type> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TYPE <Type> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:WEP <Wep> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:WEP <Wep> The command enters the value of the individual bits of the frame control field. Parameters: <Wep>...
Page 187 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:QSControl <QsControl> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:QSControl <QsControl> Sets the value for the QoS control field. Parameters: <QsControl> integer Range: #H0000,16 to #HFFFF,16 Example: BB:WLNN:FBL1:MAC:QSC #H5A5A,16 Sets the value for the QoS field to#H5A5A,16. Manual operation: "QoS Control"...
Page 188 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:SCONtrol:FRAGment: STARt <Start> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SCONtrol:FRAGment:STARt <Start> The command enters the start number of the fragment bits of the sequence control. Parameters: <Start> integer Range: #H0,4 to #HF,4 *RST: #H0,4 Example: BB:WLNN:FBL1:MAC:SCON:FRAG:STAR #H4,4 sets the start value of the fragment bits of the sequence control. Manual operation: "Start Number"...
Page 189 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:SCONtrol:STATe <State> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SCONtrol:STATe <State> The command activates/deactivates the sequence control. Parameters: <State> 0 | 1 | OFF | ON *RST: Example: BB:WLNN:FBL1:MAC:SCON:STAT ON activates the sequence control field. Manual operation: "Sequence Control" on page 65 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:STATe <State>...
Page 190 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <HtControl> integer Range: #H00000000,32 to #HFFFFFFFF,32 *RST: #H00000000,32 Example: BB:WLNN:FBL1:MAC:HTC #H5a5a5a5a,32 Sets the value for the HT control field to #H5a5a5a5a,32. Manual operation: "HT/VHT/HE Control" on page 83 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:ACConstraint <AcConstraint> Sets the value for the AC signal field. 0 = The response may contain data from any TID (Traffic Identifier).
Page 191 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CALibration:SEQuence <Sequence> Sets the value for the calibration sequence. Parameters: <Sequence> integer Range: #H0,2 to #H3,2 Example: BB:WLNN:FBL1:MAC:HTC:CAL:SEQ #H3,2 Sets the value for the calibration sequence. Manual operation: "Calibration Sequence" on page 85 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CSISteering <CsiSteering>...
Page 192 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "Reserved" on page 85 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:VHTControl: HVINdicator? [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:HVINdicator? The command queries the used format (HT or VHT). Return values: <HTVHT> integer Example: BB:WLNN:FBL:MAC:HTC:HVIN? Response: 1 HT format is used. Usage: Query only Manual operation: "HT/VHT"...
Page 193 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "Link Adaption Control" on page 85 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:NDP <Ndp> Sets the value of the Null Data Packet (NDP) announcement. 0 = no NDP will follow 1 = NDP will follow Parameters: <Ndp>...
Page 194 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:SREServed <Reserved> This signal field is currently defined, but not used. Parameters: <Reserved> integer Manual operation: "Reserved" on page 85 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:HTControl:STATe <State> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:STATe <State> The command enables/disables HT Control. Parameters: <State> 0 | 1 | OFF | ON *RST: Example: BB:WLNN:FBL1:MAC:HTC:STAT ON...
Page 195 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings .........198 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:RDGMore ........198 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:UMFB ......199 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:VREServed [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl <VHTContol> The command sets the value for the VHT control field. Parameters: <VHTContol> integer Range: #H00000000,32 to #HFFFFFFFF,32 *RST: #H00000000,32 Example: BB:WLNN:FBL1:MAC:VHTC #H5a5a5a5a,32 sets the value for the VHT control field.
Page 196 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "Coding Type" on page 88 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:FTTYpe <FbTxType> The command sets the FB Tx Type subfield. 0 = If the Unsolicited MFB subfield is set to 1 and FB Tx Type subfield is set to 0, the unsolicited MFB refers to either an unbeamformed VHT PPDU or transmit diversity using an STBC VHT PPDU.
Page 197 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:MFB <Mfb> The command sets the MFB subfield. This subfield contains the recommended MFB. The value of MCS=15 and VHT N_STS=7 indicates that no feedback is present. See also Table 3-12 for definition of the MFB subfield. Parameters: <Mfb>...
Page 198 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:MSI <Msi> The command sets the MSI subfield. MRQ = 0 When the MRQ subfield is set to 0, the MSI subfield is reserved. MRQ = 1 When the MRQ subfield is set to 1, the MSI subfield contains a sequence number in the range 0 to 6 that identifies the specific request.
Page 199 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings if the MFB is not a response to an MRQ. Example: BB:WLNN:FBL:MAC:VHTC:UMFB #B1,1 sets the information for the UMFB subfield. Manual operation: "Unsolicited MFB" on page 87 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:VREServed <VhtReserved> This signal field is currently defined, but not used. It is set to zero by the transmitter and ignored by the receiver.
Page 200 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Return values: <HEIndicator> integer Usage: Query only Manual operation: "HE" on page 91 6.9.5.5 Trigger frame settings ......200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:BW ..... 200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CINDication ..... 200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CSRequired ....200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:DOPPler .......200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:GILTf ....201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:HREServed ......
Page 201 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: HREServed <HESIGAReserved> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LEN <Length> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LESSeg <LDPCExtSymSeg> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:MLTFmode <MUMIMOLTFMode> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:NHLSym <NumHeLtfSym> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: PEXTension <PacketExtension> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:RSV <Reserved> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:SPAReuse <SpatialReuse> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:STBC <STBC> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:TFTYpe <TrigFrmType> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:TTYPe? [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:TXPow <APTxPower> Sets the value bits of the common info field. Parameters: <APTxPower>...
Page 202 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: TDUSerinfo <TrigDepUserInfo> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: TRSSi <TargetRssi> Sets the value bits of the user info field. You can configure the user info for up to 37 users with the command SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:NUINfo. Parameters: <TargetRssi> 7 bits Manual operation: "Target RSSI"...
Page 203: Beacon Configuration
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:TPTime <TrigProcTime> Sets minimum time to process the trigger frame in microseconds. Parameters: <TrigProcTime> TPT0 | TPT8 | TPT16 TPT0|TPT8|TPT16 0/8/16 us *RST: TPT0 Example: SOURce1:BB:WLNN:FBLock1:TFConfig:TPTime? // Response in microseconds: "8" The minimum time to process the trigger frame is 8 microsec- onds.
Page 204 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Return values: <DCCHannel> integer Example: BB:WLNN:FBL1:BFC:DCCH? Usage: Query only Manual operation: "DSSS(Current Channel)" on page 69 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:IAWindow <IAWindow> Sets the parameters necessary to support an IBSS (2 bytes). The Information field contains the ATIM Window parameter. Parameters: <IAWindow>...
Page 205 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:TSTamp <TStamp> Sets the value of the TSF timer (Timing Synchronization Function of a frame’s source). Parameters: <TStamp> integer Example: BB:WLNN:FBL1:BFC:TST #H1414AFAE891254BC, 64 Sets the value of the TSF timer to 1414AFAE891254BC. Manual operation: "Timestamp (hex)"...
Page 206 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <CCAGility> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL1:BFC:CAP:CAG ON Informs the associated stations that channel agility is used. [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:CPOLlable <CCPollable> Informs the associated stations if contention free is pollable. Parameters: <CCPollable>...
Page 207 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <IBACk> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL1:BFC:CAP:IBACk ON Informs the associated stations that immediate block Ack is allowed. [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:IBSS <CIBSs> Informs the associated stations if the network is an IBSS type network. Parameters: <CIBSs>...
Page 208 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:PBCC <PBCC> Informs the associated stations if PBCC is allowed. Parameters: <PBCC> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL1:BFC:CAP:PBCC ON Informs the associated stations that PBCC is allowed. [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:PRIVacy <PRIVacy>...
Page 209 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:SMGMt <SMGMt> Informs the associated stations if spectrum management is enabled. Parameters: <SMGMt> 1 | ON | 0 | OFF *RST: Example: SOUR:BB:WLNN:FBL1:BFC:CAP:SMGM ON Informs the associated stations that spectrum management is enabled.
Page 210 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:HTCapability:STATe <State> Activates/ deactivates the HT capability information element. Parameters: <State> 1 | ON | 0 | OFF *RST: Manual operation: "State" on page 74 6.9.6.3 ERP parameters ......210 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:ERP:BPMode ......210 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:ERP:NEPResent .......
Page 211: Spatial Mapping Configuration
® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL1:BFC:ERP:UPR ON Informs associated stations that they have to use protection. 6.9.7 Spatial mapping configuration ..........211 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:MODE ..........212 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:TSHift<st> ..........212 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:INDex ......212 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:ROW<st>:COL<dir>:I? .......212 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:ROW<st>:COL<dir>:Q? [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:MODE <Mode> Selects the spatial mapping mode for the selected frame block. Except of the beam- forming mode, the matrix element values are loaded by using info class methods.
Page 212 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:TSHift<st> <TShift> Sets the spatial mapping time shift. This value is relevant for spatial mapping mode direct and spatial expansion only. Parameters: <TShift> float Range: -32000 ns to 32000 ns Increment: 1 ns *RST: 0 ns Example:...
Page 213 ® Remote-control commands R&S SMW-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL1:SMAP:ROW2:COL2:Q? queries the time shift value of element Q for row 2, column 2. Usage: Query only Manual operation: "Q (Transmit Matrix)" on page 94 User Manual 1175.6749.02 ─ 27...
Page 214: Glossary: Application Notes And White Papers
® Glossary: Application notes and white papers R&S SMW-K54/-K86/-K142/-K147 Glossary: Application notes and white papers Symbols 1GP56: Rohde & Schwarz application note "802.11 Packet Error Rate Testing": https://www.rohde-schwarz.com/appnote/1GP56.html 1GP94: Rohde & Schwarz application note "Generating Signals for WLAN 802.11ac": https://www.rohde-schwarz.com/appnote/1GP94.html 1GP115: Rohde &...
Page 215: List Of Commands
® List of commands R&S SMW-K54/-K86/-K142/-K147 List of commands [:SOURce<hw>]:BB:WLNN:ANTenna:CMODe?....................142 [:SOURce<hw>]:BB:WLNN:ANTenna:MODE....................142 [:SOURce<hw>]:BB:WLNN:ANTenna:NOBB?....................143 [:SOURce<hw>]:BB:WLNN:ANTenna:SYSTem.....................143 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:OUTPut:DESTination........... 143 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:OUTPut:FSELect............144 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:IMAGinary............144 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:MAGNitude............. 145 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:PHASe............144 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:REAL.............. 144 [:SOURce<hw>]:BB:WLNN:BWidth....................... 122 [:SOURce<hw>]:BB:WLNN:CFBLock......................146 [:SOURce<hw>]:BB:WLNN:CLIPping:LEVel....................125 [:SOURce<hw>]:BB:WLNN:CLIPping:MODE....................125 [:SOURce<hw>]:BB:WLNN:CLIPping:SPPState................... 126 [:SOURce<hw>]:BB:WLNN:CLIPping:STATe....................126 [:SOURce<hw>]:BB:WLNN:CLOCk:MODE....................141 [:SOURce<hw>]:BB:WLNN:CLOCk:SOURce....................142 [:SOURce<hw>]:BB:WLNN:DFBLock......................146 [:SOURce<hw>]:BB:WLNN:FBLock:APPend....................146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BCHG...................
Page 216 ® List of commands R&S SMW-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:IAWindow............204 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:SRATe............... 204 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:SSID..............204 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:TSTamp............. 205 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BMCS................... 169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BOOSt..................147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BSSColor..................170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BWINd..................170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CBINonht..................153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:MUNum<st>..............177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:RUALlocation<st>..............170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:RUSelection<st>..............177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:MUNum<st>..............177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:RUALlocation<st>..............171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:RUSelection<st>..............177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CENRu<st>.................. 178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:ENCoder?...............154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:RATE................154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:TYPE................154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:COPY................... 146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CURPe?..................171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA....................
Page 217 ® List of commands R&S SMW-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol................185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:FDS..............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MDATa..............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MFRagments............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:ORDer..............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PMANagement............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PVERsion............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:RETRy..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:SUBType............. 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TDS..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TYPE..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:WEP..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCS:STATe................186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl................189 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:ACConstraint............190 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CALibration:POSition......... 190 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CALibration:SEQuence........191 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CSISteering............191 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:FREQuest............191 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:HVINdicator?............192 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:LAControl............192 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:NDP..............193 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:RDGMore............193 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:REServed............193 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:SREServed............
Page 218 ® List of commands R&S SMW-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MCS..................... 159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MODulation<st>................159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU:COUNt................180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU:EOF.................. 182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:DSELection............180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:LENGth............181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:PATTern............181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:SOURce............182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MU<st0>:GID................160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MU<st0>:NSTS................160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MUMimo:STATe................159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:NONOfdmaUser................173 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:NTPS....................160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PAID:PATTern................161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PASTe...................147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PED?.................... 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat..................174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFPFactor?.................. 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PLCP:FORMat................161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PLCP:LCBit:STATe...............161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PMODe..................150 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:POFDma..................
Page 219 ® List of commands R&S SMW-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:TYPE.................... 151 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:UINDex..................168 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:DCM................154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:GAIN................178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:MRUindex..............178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:MUMimo:STATe?............178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:NSTS................179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:RUTYpe..............179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STAid................179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STATe................. 179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:TXBF................180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:ENCoder?...........154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:RATE............154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:TYPE............154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:BPSymbol?............ 155 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:LENGth............156 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:RATE?............156 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:SYMBols............157 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DPNSeed:STATe............157 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:ILEaver:STATe............158 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:ADDRess<st>..........184 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:ADDRess<st>:STATe........184 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:DID..............
Page 220 ® List of commands R&S SMW-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MODulation<st>............159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU:COUNt............180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU:EOF.............. 182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:DSELection........180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:LENGth........181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:PATTern........181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:SOURce........182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:PNSeed..............162 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:MODE........... 164 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:PATTern..........165 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SERVice:PATTern.............165 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:BW..........200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CINDication........200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CSRequired........200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:DOPPler........200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:GILTf..........200 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:HREServed........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LEN..........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LESSeg......... 201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:MLTFmode........
Page 221 ® List of commands R&S SMW-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:RCOSine................129 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:SPHase................129 [:SOURce<hw>]:BB:WLNN:FILTer:TYPE...................... 130 [:SOURce<hw>]:BB:WLNN:IFBLock......................146 [:SOURce<hw>]:BB:WLNN:PFBLock......................147 [:SOURce<hw>]:BB:WLNN:PRESet......................122 [:SOURce<hw>]:BB:WLNN:SETTing:CATalog?.................... 122 [:SOURce<hw>]:BB:WLNN:SETTing:DELete....................123 [:SOURce<hw>]:BB:WLNN:SETTing:LOAD....................123 [:SOURce<hw>]:BB:WLNN:SETTing:STORe....................123 [:SOURce<hw>]:BB:WLNN:SRATe:VARiation....................130 [:SOURce<hw>]:BB:WLNN:SRATe?......................130 [:SOURce<hw>]:BB:WLNN:STATe........................ 124 [:SOURce<hw>]:BB:WLNN:TRIGger:ARM:EXECute..................132 [:SOURce<hw>]:BB:WLNN:TRIGger:EXECute..................... 132 [:SOURce<hw>]:BB:WLNN:TRIGger:EXTernal:SYNChronize:OUTPut............132 [:SOURce<hw>]:BB:WLNN:TRIGger:OBASeband:DELay................133 [:SOURce<hw>]:BB:WLNN:TRIGger:OBASeband:INHibit................133 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:DELay................141 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FBINdex................138 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FESHift................. 139 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FINDex................139 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:MODE................
Page 222: Index
® Index R&S SMW-K54/-K86/-K142/-K147 Index Delay Marker ............... 115 AC constraint ..............84 Trigger ............... 111 VHT ................87 Disable Barker spreading (CCK, PBCC) ......36 Addresses ................. 65 Documentation overview ............. 9 Aggregated control ............90 Doppler ................41 Antennas ................
Page 223 ® Index R&S SMW-K54/-K86/-K142/-K147 Generate No TXOP PS ..............60 Waveform file .............. 20 Nsts ................... 53 Getting started ..............9 NSTS ................. 33 GID-H Number of data symbols ........... 57 VHT ................88 Number of MU-MIMO users ........51, 52, 54 Group ID ................
Page 224 ® Index R&S SMW-K54/-K86/-K142/-K147 Signal generation status ..........108 Videos ................11 Single ................108 Smoothing ................. 60 Space time block coding ........... 32 Waveform file Space time streams ............ 31, 33 Create ................. 20 Spatial mapping mode ............93 White papers ..............10 Spatial reuse ...............

This manual is also suitable for:

R&s smw-k86 R&s smw-k142 R&s smw-k147

Rohde & Schwarz R&S SMW-K54 User Manual

Table of Contents

1 Welcome to the IEEE 802.11 WLAN Digital Standard

2 About the IEEE 802.11 WLAN Options

3 WLAN Configuration and Settings

Settings Data Length

Section 3

4 How to Work with the IEEE 802.11 WLAN Option

5 Signal Control and Signal Characteristics

Section 4

6 Remote-Control Commands

Glossary: Application Notes and White Papers

List of Commands

Index

Quick Links

Chapters

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Rohde & Schwarz R&S SMW-K54

Summary of Contents for Rohde & Schwarz R&S SMW-K54

This manual is also suitable for:

Table of Contents