Page 1 ® R&S SMBVB-K54/-K86/-K142/-K147 IEEE 802.11a/b/g/n/ac/ax/be User Manual (;ÜàD2) 1178822002 Version 10...
Page 2 This document describes the following software options: ● R&S ® SMBVB-K54 IEEE 802.11a/b/g/n/j/p (1423.7824.xx) ● ® R&S SMBVB-K86 IEEE 802.11ac (1423.7924.xx) ● ® R&S SMBVB-K142 IEEE 802.11ax (1423.8114.xx) ● R&S ® SMBVB-K147 IEEE 802.11be (1423.8950.xx) ® This manual describes firmware version FW 5.30.305.xx and later of the R&S SMBV100B.
Page 3: Table Of Contents
® Contents R&S SMBVB-K54/-K86/-K142/-K147 Contents 1 Welcome to the IEEE 802.11 WLAN digital standard......7 Key features........................7 Accessing the IEEE 802.11 WLAN dialog..............8 What's new........................8 Documentation overview....................9 1.4.1 Getting started manual....................9 1.4.2 User manuals and help....................9 1.4.3 Service manual....................... 9 1.4.4 Instrument security procedures..................10 1.4.5...
Page 4 ® Contents R&S SMBVB-K54/-K86/-K142/-K147 3.4.5 Data settings......................... 56 A-MPDU settings......................62 MAC header and FCS configuration for frame block..........64 3.6.1 MAC header and FCS common settings...............65 3.6.2 MAC header and frame control settings................65 3.6.3 MAC HT/VHT/HE control settings................. 70 3.6.4 Beacon frame settings....................
Page 5 ® Contents R&S SMBVB-K54/-K86/-K142/-K147 6.9.1 Frame block PPDU configuration................151 6.9.2 EHT/HE configuration....................168 6.9.3 User configuration....................... 176 6.9.4 MPDU configuration....................180 6.9.5 MAC header configuration..................182 6.9.6 Beacon configuration....................204 6.9.7 Spatial mapping configuration..................211 Glossary: Specifications and references.........214 List of commands................215 Index....................222 User Manual 1178.8220.02 ─...
Page 6 ® Contents R&S SMBVB-K54/-K86/-K142/-K147 User Manual 1178.8220.02 ─ 10...
Page 7: Welcome To The Ieee 802.11 Wlan Digital Standard
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMBVB-K54/-K86/-K142/-K147 Key features 1 Welcome to the IEEE 802.11 WLAN digital standard The options R&S SMBVB-K54/-K86/-K142/-K147 are firmware applications that add functionality to generate signals in accordance with the wireless LAN standards IEEE 802.11a/b/g/n/ac/p/j/ax/be.
Page 8: Accessing The Ieee 802.11 Wlan Dialog
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMBVB-K54/-K86/-K142/-K147 What's new VHT-20 MHz, VHT-40 MHz, VHT-80 MHz, VHT-80+80 MHz, VHT-160 MHz ● Support of all 11ax transmission modes with option R&S SMBVB-K142: HE-20 MHz, HE-40 MHz, HE-80 MHz, HE-80+80 MHz, HE-160 MHz ●...
Page 9: Documentation Overview
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMBVB-K54/-K86/-K142/-K147 Documentation overview Compared to the previous version it provides the new features listed below: ● Renaming 802.11 to IEEE 802.11 ● Editorial changes 1.4 Documentation overview This section provides an overview of the R&S SMBV100B user documentation. Unless specified otherwise, you find the documents at: www.rohde-schwarz.com/manual/smbv100b 1.4.1 Getting started manual...
Page 10: Instrument Security Procedures
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMBVB-K54/-K86/-K142/-K147 Documentation overview 1.4.4 Instrument security procedures Deals with security issues when working with the R&S SMBV100B in secure areas. It is available for download on the internet. 1.4.5 Printed safety instructions Provides safety information in many languages.
Page 11: Videos
® Welcome to the IEEE 802.11 WLAN digital standard R&S SMBVB-K54/-K86/-K142/-K147 Notes on screenshots 1.4.10 Videos Find various videos on Rohde & Schwarz products and test and measurement topics on YouTube: https://www.youtube.com/@RohdeundSchwarz On the menu bar, search for your product to find related videos. Figure 1-1: Product search on YouTube 1.5 Scope Tasks (in manual or remote operation) that are also performed in the base unit in the...
Page 12: About The Ieee 802.11 Wlan Options
® About the IEEE 802.11 WLAN options R&S SMBVB-K54/-K86/-K142/-K147 About IEEE 802.11 WLAN technology 2 About the IEEE 802.11 WLAN options 2.1 Required options The basic equipment layout for generating IEEE 802.11 WLAN signals includes: ● Base unit ● Baseband real-time extension (R&S SMBVB-K520) ●...
Page 13 ® About the IEEE 802.11 WLAN options R&S SMBVB-K54/-K86/-K142/-K147 About IEEE 802.11 WLAN technology IEEE 802.11be further extends IEEE 802.11ax offering frequency bands at 2.4 GHz, 5 GHz and 6 GHz. It supports uplink and downlink multi-user MIMO and up to 320 MHz bandwidth.
Page 14: Operation Modes
® About the IEEE 802.11 WLAN options R&S SMBVB-K54/-K86/-K142/-K147 Operation modes Parameters IEEE 802.11a IEEE 802.11b IEEE 802.11g IEEE 802.11j IEEE 802.11p Transmission tech- SISO SISO SISO SISO SISO nology Modulation OFDM DSSS DSSS, OFDM OFDM OFDM, OFDMA Data subcarrier BPSK, QPSK, CCK, PBCC CCK, PBCC,...
Page 15 ® About the IEEE 802.11 WLAN options R&S SMBVB-K54/-K86/-K142/-K147 Operation modes Figure 2-1: PLCP packet format for IEEE 802.11n 1 = Operation mode "Legacy" 2 = Operation mode "Mixed Mode" 3 = Operation mode "Green Field" Table 2-3 gives an overview of the frequency domain operation modes of the physical layer.
Page 16: Signal Generation
® About the IEEE 802.11 WLAN options R&S SMBVB-K54/-K86/-K142/-K147 Signal generation 2.4 Signal generation The generation of an IEEE 802.11n/ac/ax signal is done in multiple steps. In high throughput (HT) and very high throughput (VHT) modes, the data of a single user is specially coded and transmitted via up to eight Tx antennas.
Page 17: Wlan Configuration And Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 General settings 3 WLAN configuration and settings Access: ► Select "Baseband > IEEE 802.11". The remote commands required to define these settings are described in Chapter 6, "Remote control commands", on page 119. ●...
Page 18 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 General settings Sample Rate......................... 20 Transmit Antennas Setup....................20 Filter/Clipping Settings....................20 State Activates the standard and deactivates all the other digital standards and digital modu- lation modes in the same path. Remote command: on page 124 [:SOURce<hw>]:BB:WLNN:STATe Set to Default...
Page 19 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 General settings Parameter Value "Space Time Streams" "Extended Spatial Streams" "Space Time Block Coding" inactive Parameter value "MCS" "Data Rate (Mbps)" "Data Bits Per Symbol" "Stream 1" QPSK "Channel Coding" "Coding Rate" ½ "Guard"...
Page 20 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 General settings Remote command: on page 123 [:SOURce<hw>]:BB:WLNN:SETTing:CATalog? on page 124 [:SOURce<hw>]:BB:WLNN:SETTing:LOAD on page 124 [:SOURce<hw>]:BB:WLNN:SETTing:STORe on page 123 [:SOURce<hw>]:BB:WLNN:SETTing:DELete Generate Waveform File With enabled signal generation, triggers the instrument to save the current settings of an arbitrary waveform signal in a waveform file with predefined extension *.wv.
Page 21: Transmit Antenna Setup
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Transmit antenna setup 3.2 Transmit antenna setup Access: ► Select "Baseband > IEEE 802.11 > General > Transmit Antennas Setup". This dialog is used to map the generated Tx chains to different destinations ("Base- band A/B", "File"...
Page 22 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Transmit antenna setup Transmission Antenna Table Configures the output matrix and transmission chain matrix coefficients. During signal calculation, the R&S SMBV100B evaluates the transmission chain matrix and takes into account the set phase ratios. However, the power ratio of the antennas is not considered.
Page 23: Frame Block Configuration
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration 3.3 Frame block configuration Access: ► Select "Baseband > IEEE 802.11 > Frame Blocks". This tab provides settings to select and configure a frame block. Settings: Std..........................23 Type..........................24 Physical Mode.......................25 Mode........................
Page 24 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration Table 3-1: Availability "Standard", "Type", "Physical Mode", "TxMode" Standard Type Physical mode Txmode User 11a/g Data/Beacon/Trigger Legacy L-20MHz L-Duplicate L-Upper L-Lower 11b/g Data/Beacon/Trigger Legacy PBCC 11p/j Data/Beacon/Trigger Legacy L-10MHz Mixed Mode/Green Field HT-20MHz HT-40MHz HT-Duplicate...
Page 25 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration "Beacon" A frame of type "Beacon" contains all the information about a net- work, for example the beacon interval, capability information and the IBSS parameter set. The access point (AP) of a service set periodi- cally transmits the beacon frame to establish and maintain the net- work.
Page 26 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration Table 3-3: Tx modes for "Type > Data/Trigger" and "Physical Mode > Mixed Mode" Tx mode Transmission bandwidth 20 MHz 40 MHz 80 MHz 160 MHz 320 MHz HT-20MHz HT-40MHz HT-Duplicate HT-Upper HT-Lower...
Page 27 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration Table 3-5: Tx modes for "Type > Sounding" and "Physical Mode > Mixed Mode" Tx mode Transmission bandwidth 20 MHz 40 MHz 80 MHz 160 MHz 320 MHz HT-20MHz HT-40MHz HT-Duplicate HT-Upper HT-Lower...
Page 28 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration Frames Sets the number of frames to be transmitted in the current frame block. Remote command: on page 147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:FCOunt Idle Time /ms Sets the time interval separating two frames in this frame block. Remote command: on page 149 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:ITIMe...
Page 29 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration Remote command: on page 147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BOOSt PPDU When clicking "Conf ...", accesses the settings for configuring the PPDU of frame blocks. See Chapter 3.4, "PPDU configuration", on page 30. Remote command: n.a.
Page 30: Ppdu Configuration
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration 3.4 PPDU configuration This chapter describes the physical protocol data unit (PPDU) settings. Access: ► Select "Frame Blocks > PPDU > Conf...". The dialog provides settings to configure PPDU parameters. Available settings depend on the WLAN IEEE 802.11 standard, frame type, physical mode and TX mode.
Page 31 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration 2. Select the side-tab "General" > "Stream Settings". This dialog provides settings to configure spatial streams. Settings: Spatial Streams......................31 Space Time Streams.....................31 Extended Spatial Streams.....................31 Multi User MIMO......................31 Segment........................32 Space Time Block Coding.....................
Page 32 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Activates multi-user MIMO. Activation requires to "Spatial Streams > 1". Remote command: on page 159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MUMimo:STATe Segment Requires a two-segment channel, e.g. "Tx Mode > HE-80+80MHz". Example: To set segments for fixed transmission bandwidth For "Transmission Bandwidth >...
Page 33 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Settings: User Index........................33 Multi User MIMO Settings Table..................33 User Index Defines the currently generated user. For "Multi User MIMO > Active", only one user can be generated at a time. This parameter selects the generated one out of four avail- able users.
Page 34 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Rate........................35 Guard..........................35 DCM..........................35 Selects the modulation and coding scheme for all spatial streams. Remote command: on page 158 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MCS on page 158 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MCS Data Rate /Mbps Indicates the PPDU data rate. Remote command: on page 149 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:RATE?
Page 35 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Encoders Displays the number of encoders to be used. This value depends on the data rate. For data rates smaller or equal 300 Mbit/s, this value is 1. Otherwise, the number of encod- ers is 2.
Page 36: He Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Settings PSDU Bit Rate......................36 PSDU Modulation......................36 Barker Spreading......................36 PSDU Bit Rate Requires "Tx Mode > CCK/PBCC". Selects the bit rate of the PSDU. The data rates available are 1 Mbps, 2 Mbps, 5.5 Mbps, 11 Mbps and 22 Mbps. The 1 Mbps data rate is only available if the long PLCP format has been selected.
Page 37 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Access: 1. Select "IEEE 802.11..." > "Frame Blocks". 2. Select "Std" > "11ax" or "Std" > "User". 3. Select "Tx Mode" > "HE-x". "x" represents the bandwidth and type of HE frame, e.g. "x" = "80+80MHz". 4.
Page 38 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration In the HE-SIG-A field of an HE MU PPDU, the bits of the Bandwidth field specify punc- tured subchannels. Theses subchannels have a length of 20 MHz and are part of pri- mary and secondary channels with a length of 20 MHz to 80 MHz.
Page 39 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration b) Check the default settings for punctured and unpuctured 20 MHz subchannels Figure 3-1. Figure 3-1: Bandwidth bit 7: Punctured and unpuctured 20 MHz 1 = Unpunctured subchannels (read-only) 2 = Punctured subchannels 3 = Unpunctured subchannels (configurable) The third subchannel "SubCh2"...
Page 40 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 172 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:LINK Guard Selects which guard interval is used for the OFDM guard. For "Physical Mode" > "Green Field"/"Legacy", the field is read only, since the modes have long guard intervals only.
Page 41 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat EHT-LTF Symb Duration/HE-LTF Symb Duration Selects the duration of the EHT/HE Long Training Field (LTF) symbol. The duration does not include the length of the guard interval. Available values are multiples of a single LTF symbol duration: 3.2 μs (1x LTF), 6.4 μs (2x LTF) and 12.8 μs (4x LTF) Remote command:...
Page 42 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Preamble Puncturing Requires "Tx Mode" > "HE-80MHz"/"HE-80+80MHz"/"HE-160MHz" and "PPDU For- mat" > "HE MU". Enables preamble puncturing of the HE MU PPDU in 80 MHz, 80+80 MHz or 160 MHz channels. If enabled, specific 20 MHz subchannels are not transmitted, see Table 3-8.
Page 43 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BSSColor TXOP Duration If transmission opportunity (TXOP) is set to 127, it indicates no duration information. If it is set to any other value, it indicates duration information for network allocation vector (NAV) parameter and that the TXOP is protected.
Page 44 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration "6"/"7" Sets the bandwidth mode for "Tx Mode" > "HE-80+80MHz"/"HE-160MHz" channels. Remote command: on page 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PPUNcturing SubChan# Requires "Preamble Puncturing" > "On". Selects or indicates the 20 MHz subchannel that is punctured in the preamble. If enabled, this subchannel is not transmitted.
Page 45: Eht Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Output File Displays the fixed file path including the filename, in that the log file is saved. The filename consists of the digital standard "wlan" and the selected frame block. For example, the file wlan_fb7 has logging data of frame block 7.
Page 46 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration 2. Select the side tab "General > EHT General". This tab provides general settings to configure EHT frames. Settings: Max PE Duration......................46 Disambiguity......................46 Time Domain Windowing Active..................46 Transition Time......................46 Max PE Duration Selects the maximum packet extension (PE) duration.
Page 47 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration 3.4.3.2 U-SIG settings Access: 1. Select "PPDU > Conf... > General". 2. Select the side tab "U-SIG". This dialog provides additional settings to configure the Universal SIGNAL field. Settings: Link Direction........................ 47 PPDU Format........................47 Spatial Reuse...
Page 48 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration "EHT TRIG/HE TRIG" Requires "Link Direction > Uplink". Carries a single PSDU. It is sent as a response to a PPDU that con- tains a trigger frame. Remote command: on page 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat Spatial Reuse 1/2 Requires "PPDU Format >...
Page 49 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:EMCS 320MHz Type Requires "Transmission Bandwidth" = 320 MHz. Sets the type of channelization of 320 MHz channels in the bandwidth (BW) field of the U-SIG-1 field. The channelization affects two adjacent 160 MHz channels of a 320 MHz channel in the 6 GHz band.
Page 50 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration EHT-LTF Symb Duration/HE-LTF Symb Duration............50 Non-OFDMA Users....................... 50 EHT-SIG Diff per 80MHz....................50 pre-FEC Padding Factor Displays the pre forward error condition (FEC) padding factor used in the trigger PPDU. Remote command: on page 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFPFactor?
Page 51: User Configuration Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration 3.4.3.4 Logging settings Access: 1. Select "PPDU" > "Conf..." > "General". 2. Select the side tab "Logging". The tab provides settings to configure logging for EHT/HE frames. Settings: Logging State........................ 51 Output File........................51 Logging State...
Page 52 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Multiple users for IEEE 802.11ax Since multiple users are intended recipients in the OFDMA downlink, the AP needs to tell the STAs which resource unit belongs to them. In IEEE 802.11ax, the AP uses the HE SIG-B field in the HE_MU_PPDU for this purpose.
Page 53 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration The tab provides the settings for first and second content channel. Settings 1st/2nd Content Channel....................53 └ Selection....................53 └ Allocation....................53 └ Number of MU-MIMO users................53 └ Center 26-tone RU..................54 1st/2nd Content Channel Defines the settings of the common field and user-specific field of an EHT-SIG content channel or an HE-SIG-B content channel.
Page 54 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Remote command: on page 178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:MUNum<st> on page 177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:MUNum<st> Center 26-tone RU ← 1st/2nd Content Channel For HE frames. Requires "PPDU Format > HE MU/HE TRIG". For full bandwidth 80 MHz: if enabled, indicates that center 26 -tone RU is allocated in the common block fields of both SIGB content channels with same value.
Page 55 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Remote command: EHT[:SOURce<hw>]:BB:WLNN:FBLock<ch>:BEUL? on page 169 STA Id Sets the station ID, the 11 least significant bits of the association identifier (AID). Remote command: on page 179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STAid Nsts Sets the number of space time streams allocated to a particular user. If "Space time stream"...
Page 56: Data Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration MU MIMO Displays if the multi-user MIMO is used for current user. All MU-MIMO users share one resource unit (RU) using different space time streams. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:MUMimo:STATe? on page 178 Gain (dB) Sets the additional gain that can be applied to the RU allocated by a particular user.
Page 57: Settings Data Length
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration 3.4.5.1 Data settings Access: 1. Select "Frame Blocks > PPDU > Config...". 2. Select "Data > Data Settings". The dialog comprises the settings for the configuration of the data. Settings Data Length........................57 Frame Duration......................
Page 58: Frame Duration
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration The maximum data length depends on the physical mode: ● In "Physical Mode > Legacy", the maximum value is 4061 bytes. ● In "Physical Mode > Mixed Mode" and "Physical Mode > Green Field", the maxi- mum value is 1048575 bytes.
Page 59: Bandwidth In Non Ht
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration "Preamble (available only for "Tx Mode > CCK/PBCC") Only" The scrambler is activated. Only the preamble is scrambled. Remote command: on page 163 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SCRambler:MODE [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:MODE on page 163 Ch. Bandwidth in Non HT (available only for "Tx Mode >...
Page 60: Duty Cycle
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration If the number of OFDM data symbols is changed, the generator calculates the data field length as a function of the set PPDU bit rate. This value is displayed at "Data Length".
Page 61: Service Field Clock Bit
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 PPDU configuration Service Field Clock Bit (available only for "Tx Mode > CCK/PBCC") Sets the locked clock bit in service field of the PLCP header. Via this flag (bit), the transmitter indicates whether transmission frequency and symbol rate have been derived from the same oscillator.
Page 62: A-Mpdu Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 A-MPDU settings Settings: Preamble/Header Active....................62 Smoothing........................62 Partial AID (hex)......................62 No TXOP PS......................... 62 Preamble/Header Active Activates preamble and signal fields of the frames in the current frame block. For "Type > Sounding", the preamble and signal field are always activated and cannot be deactivated.
Page 63 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 A-MPDU settings Access: 1. Select "IEEE 802.11... > Frame Blocks". 2. Select "Type > Data". 3. Select "Data > A-MPDU". 4. Select "DList/Pattern > Config". 5. Select "A-MPDU". The dialog comprises the A-MPDU settings. Settings: Number of MPDUs......................
Page 64: Mac Header And Fcs Configuration For Frame Block
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: on page 182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:SOURce [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:SOURce on page 182 DList / Pattern Depending on the selected data source, selects a data list or allows entering a user- defined bit pattern.
Page 65: Mac Header And Fcs Common Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Settings: ● MAC header and FCS common settings..............65 ● MAC header and frame control settings..............65 ● MAC HT/VHT/HE control settings................70 ● Beacon frame settings.................... 80 ●...
Page 66: Settings: Frame Control (Hex)
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Settings: Frame Control (hex)...................... 66 MAC Frame Control Field..................... 66 Duration ID (hex)......................67 Address........................ 67 (hex)........................68 BSSID (hex)........................68 Sequence Control......................68 └ Start Number (hex)..................
Page 67: Duration Id (Hex)
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:WEP on page 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:ORDer [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol on page 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol: on page 185 PVERsion [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:TYPE on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:SUBType on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:TDS on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:FDS...
Page 68: Sa (Hex)
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: on page 184 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:ADDRess<st>:STATe [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:ADDRess<st>: on page 184 STATe SA (hex) Requires PPDU "Type" > "Beacon". Enters the value of the source address (SA) field. Remote command: on page 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SA...
Page 69: Start Number (Hex)
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block If you want to simulate, that a receiver receives some packets incorrectly, set "Incre- mented Every" > "2 packets" or higher. The R&S SMBV100B sends each packet with identical data twice.
Page 70: Mac Ht/Vht/He Control Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SCONtrol:FRAGment:INCRement on page 187 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SCONtrol:SEQuence:INCRement on page 188 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:SCONtrol: on page 187 FRAGment:INCRement [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:SCONtrol: on page 188 SEQuence:INCRement HT Config/VHT Config/HE Config Accesses settings to configure the HT/VHT/HE Control field. See Chapter 3.6.3, "MAC HT/VHT/HE control settings",...
Page 71 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block ● "Tx Mode" > "VHT-x": Select "MAC Header & FCS" > "VHT Config". Figure 3-3: MAC VHT control ● "Tx Mode" > "HE-x"/"EHT-x": Select "MAC Header & FCS" > "HE Config". Figure 3-4: MAC HE/EHT control Chapter 3.6.3.4, "MAC HE control settings",...
Page 72 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block The QoS solicits an acknowledgement policy from the receiver, according to specific feedback rules. QoS control ensures a high level of transmission performance like high bit rate, low latency or low bit error probability.
Page 73 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block RDG/More PPDU The RDG/More signal field (LSB, 1 bit) issues the reverse direction grant. When trans- mitted by an initiator or a responder, this field is interpreted differently. Transmitted by initiator 0 = No reverse grant.
Page 74 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CSISteering on page 191 Reserved This signal field (2 bit) is defined, but not used. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:SREServed on page 194 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:FREQuest on page 191 Calibration Sequence Identifies the calibration sequence (2 bit).
Page 75 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block B6-B8 (3bit) MFS - MFB sequence identifier Set to the received value of MRS. Set to '111' for unsolicited MFB. B9-B15 (7bit) MFB - MCS feedback Link adaptation feedback containing the recommended MCS.
Page 76: Rdg/More Ppdu
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block MRQ..........................78 Rsv..........................78 HT/VHT......................... 78 RDG/More PPDU The RDG/More signal field (LSB, 1 bit) issues the reverse direction grant. When trans- mitted by an initiator or a responder, this field is interpreted differently. Transmitted by initiator 0 = No reverse grant.
Page 77: Coding Type
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Coding Type If the Unsolicited MFB subfield is set to 1, the "Coding Type" subfield contains the cod- ing information (set to 0 for BCC and set to 1 for LDPC) to which the unsolicited MFB refers.
Page 78: Msi
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block If the Unsolicited MFB subfield is set to 0, the MFSI/GID-L subfield contains the received value of MSI contained in the frame to which the MFB information refers. MFB = 1 The MFSI/GID-L subfield contains the lowest 3 bits of group ID of the PPDU to which the unsolicited MFB refers.
Page 79 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 3.6.3.4 MAC HE control settings Access: 1. Select "Frame Blocks > Type > Data". 2. Select "Tx Mode" > "HE-20MHz"/"HE-40MHz"/"HE-80MHz"/"HE-80 + 80MHz"/"HE-160MHz". 3. Select "Frame Blocks" > "PPDU" > "Config...". 4.
Page 80: Beacon Frame Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:HVINdicator? on page 196 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:VHTControl: on page 192 HVINdicator? 3.6.4 Beacon frame settings A beacon frame is a management frame that contains all the information about a net- work.
Page 81 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Settings: Timestamp (hex)......................81 Beacon Interval......................81 SSID..........................81 Supported Rates......................81 DSSS(Current Channel)....................81 IBSS(ATIM Window) (hex).................... 81 Timestamp (hex) Updates the local clock of a station (the timing synchronization function (TSF) of a fra- mes' source) after receiving a beacon frame.
Page 82 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 3.6.4.2 Capability information parameters Access: 1. Select "IEEE 802.11 > Frame Blocks". 2. Select "Type > Beacon". 3. Select "PPDU > Config...". 4. Select "MAC Header & FCS >Capability Info". The dialog displays the capability info parameters.
Page 83 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Capability Information Parameters Table 3-11: Functions of capability information parameters Function If enabled this function indicates that: SCPI command name "Immediate Immediate block Ack is allowed (suitable for high- [:SOURce<hw>]:BB:WLNN: Block Ack"...
Page 84 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Function If enabled this function indicates that: SCPI command name "Short Pream- Short preamble is allowed (uses 56 instead of 128 [:SOURce<hw>]:BB:WLNN: ble" bits for the "sync" field. Created to improve WLAN FBLock<ch>: efficiency).
Page 85 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 4. Select "MAC Header & FCS > ERP". The dialog provides extended rate PHY (ERP) settings. The ERP parameters indicate special features/modes. Settings: Parameters......................85 ERP Parameters Function If enabled this function indicates that:...
Page 86: Trigger Frame Settings
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 3. Select "PPDU > Config...". 4. Select "MAC Header & FCS > HT Capability". The dialog provides HT capability information. Settings: State..........................86 Green Field........................86 State Activates/ deactivates the HT capability information element.
Page 87 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 4. Select "MAC Header & FCS". The dialog provides the trigger frame settings, including settings for the common info field, user info field and additional info settings. Common Info field and User Info field variants Common info field bits B54 and B55 specify User Info field variants (HE or EHT) in trig- ger based (TB) PPDU types.
Page 88 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Settings: Trigger Frame Type.......................88 Trigger Type........................88 Length........................... 88 Cascade Indication......................89 Required........................89 BW..........................89 LTF........................... 89 MU-MIMO LTF Mode.....................89 Num HE-LTF Symbols....................89 STBC..........................90 LDPC Ext Symb Seg.....................90 AP Tx Power.........................
Page 89 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Cascade Indication If set to 1, then there is a subsequent trigger frame. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: on page 201 CINDication CS Required If set to 1, the stations identified in the user field can sense the medium state and con- sider the nav in determining if to respond or not.
Page 90 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block STBC If set to 1, STBC encoding is used for the HE trigger-based PPDU response. Other- wise the value is set to 0. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:STBC on page 201 LDPC Ext Symb Seg...
Page 91 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block HE/EHT P160 Requires EHT frames: "Tx Mode" > "EHT-x" Sets the 1-bit value of the HE/EHT P160 field. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:HEEHt on page 201 Special User Info Field Present Specifies if the Special User Info field is present in the trigger frame or not.
Page 92 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block 2. Set "Type > Trigger" 3. Select "PPDU > Config...". 4. Select "MAC Header & FCS > User Info". This dialog provides user info field settings of the trigger frame settings. Settings: No.
Page 93 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: on page 201 RU Allocation Specifies the RU used by the HE trigger-based PPDU of the STA, which is identified by the "AID12" field value. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: on page 202...
Page 94 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: on page 202 PS160 PHY Version ID Requires "Special User Info Field Present" > "0", see "Special User Info Field Present" on page 91. Specifies the 3-bit value of the PHY Version ID field.
Page 95 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 MAC header and FCS configuration for frame block Trigger Dependent User Info The value of this field depends on the trigger variant. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: on page 202 TDUSerinfo 3.6.5.3 Additional info settings Access: 1.
Page 96: Spatial Mapping
® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Spatial mapping Padding Length Displays the padding length of a trigger frame in bytes. Remote command: [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:PADLength on page 203 3.7 Spatial mapping Access: 1. Select "Frame Blocks > PPDU > Config". 2. Select "Spatial Mapping". The dialog provides settings to configure the spatial mapping mode, the time shifts and the transmit parameters.
Page 97 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Spatial mapping so that the expectation of IQ sum-power of all antennas is 0 dBr. Also for "OFF", "Direct", and "Spatial Expansion", the expected IQ power is the same for all antennas and hence these modes can be intermixed without caring about any power regulation issue.
Page 98 ® WLAN configuration and settings R&S SMBVB-K54/-K86/-K142/-K147 Spatial mapping Time Shift Sets the spatial mapping time shift. This value is relevant for spatial mapping mode "Direct" and "Spatial Expansion" only. Remote command: on page 212 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:TSHift<st> I (Transmit Matrix) Displays the time shift value of element I of the selected row and column of the spatial transmit matrix.
Page 99: Signal Control And Signal Characteristics
® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings 4 Signal control and signal characteristics This section lists settings provided for configuring the baseband filter, for defining the signal generation start and for generating signals necessary for synchronization with other instruments.
Page 100 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Settings Use Default Wlan Filter....................100 Filter..........................100 Roll Off Factor or BxT....................100 Cut Off Frequency Factor....................101 Cut Off Frequency Shift....................101 Sample Rate Variation....................101 IFFT Upsampling......................101 Use Default Wlan Filter Requires "Transmission Bandwidth >...
Page 101 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Cut Off Frequency Factor Sets the value for the cutoff frequency factor. The cutoff frequency of the filter can be adjusted to reach spectrum mask requirements. Remote command: on page 128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASs on page 129 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASSEVM...
Page 102: Clipping Settings
® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Remote command: on page 127 [:SOURce<hw>]:BB:WLNN:FILTer:IUPSampling 4.1.2 Clipping settings Access: ► Select "Filter/Clipping Settings > Clipping". The dialog comprises the settings, necessary to configure the clipping. Settings Clipping State......................102 Clipping Level......................103 Clipping Mode......................
Page 103 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Since clipping the signal not only changes the peak value but also the average value, the effect on the crest factor is unpredictable. The following table shows the effect of the "Clipping"...
Page 104: Trigger Settings
® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings 4.2 Trigger settings Access: ► Select "Baseband" > "IEEE 802.11" > "Trigger In". This tab provides settings to select and configure the trigger, like trigger source, trigger mode and trigger delays, and to arm or trigger an internal trigger manually. The header of the tab displays the status of the trigger signal and trigger mode.
Page 105 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings Execute Trigger......................106 Trigger Source......................107 Sync. Output to External Trigger/Sync. Output to Trigger........... 107 External Trigger Inhibit....................108 Trigger Delay.......................108 Mode Selects the trigger mode. The mode determines the effect of a trigger event on the sig- nal generation.
Page 106 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings Running/Stopped With enabled modulation, displays the status of signal generation for all trigger modes. ● "Running" The signal is generated; a trigger was (internally or externally) initiated in triggered mode. ●...
Page 107 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings Trigger Source The following sources of the trigger signal are available: ● "Internal" The trigger event is internal. Tap "Execute Trigger" to trigger signal generation manually. ● "External Global Trigger" The trigger event is the active edge of an external trigger signal provided and con- figured at the User x connectors.
Page 108: Marker Settings
® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Marker settings In primary-secondary instrument mode, this setting ensures that once achieved, syn- chronization is not lost if the baseband signal sampling rate changes. Remote command: [:SOURce<hw>]:BB:WLNN:TRIGger:EXTernal:SYNChronize:OUTPut on page 133 External Trigger Inhibit Applies for an external trigger signal.
Page 109 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Marker settings The tab provides access to the settings necessary to select and configure the marker output signal, like the marker mode or marker delay settings. This section focuses on the available settings. For detailed information, see section "Common characteristics of the baseband domain"...
Page 110 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Marker settings "Frame" "Number of Frame Blocks" = 1, that is, a marker signal is generated at the start of each frame in the single frame block. Otherwise, the frame block and frame index are entered and the specific frame is masked.
Page 111 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Marker settings "Frame Active Part / Frame Inactive Part" A marker signal is generated to mark every active part of each frame. The active data transfer part (PPDU) of a frame period is marked with high, the inactive part (idle time) with low.
Page 112 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Marker settings decrease the carrier leakage during inactive signal parts by feeding it into the pulse modulator. Otherwise, the frame block and frame index are entered and the active part of the specific frame is masked. The parameters "Rising Edge Shift / Falling Edge Shift"...
Page 113: Clock Settings
® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Clock settings "Pulse" A regular marker signal is generated. The clock frequency is defined by entering a divider. The frequency is derived by dividing the chip rate by the divider. The input box for the divider opens when "Pulse" is selected, and the resulting pulse frequency is displayed below it.
Page 114: Global Connectors Settings
® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Global connectors settings This tab provides access to the settings necessary to select and configure the clock signal, like the clock source and clock mode. This section focuses on the available settings. For detailed information, see section "Common characteristics of the baseband domain"...
Page 115 ® Signal control and signal characteristics R&S SMBVB-K54/-K86/-K142/-K147 Global connectors settings See also chapter "Global connectors settings" in the user manual. User Manual 1178.8220.02 ─ 10...
Page 116: How To Work With The Ieee 802.11 Wlan Option
® How to work with the IEEE 802.11 WLAN option R&S SMBVB-K54/-K86/-K142/-K147 Generating a realistic MxN MIMO WLAN IEEE 802.11n/ac/p signal for receiver test under static conditions 5 How to work with the IEEE 802.11 WLAN option The R&S SMBV100B equipped with the option digital standard IEEE 802.11 WLAN allows you to generate signals for different transmitter and receiver tests scenarios.
Page 117 ® How to work with the IEEE 802.11 WLAN option R&S SMBVB-K54/-K86/-K142/-K147 Generating a realistic MxN MIMO WLAN IEEE 802.11n/ac/p signal for receiver test under static conditions 2. Use the default "Frame Block Configuration" settings or adjust them as required. 3.
Page 118 ® How to work with the IEEE 802.11 WLAN option R&S SMBVB-K54/-K86/-K142/-K147 Generating a realistic MxN MIMO WLAN IEEE 802.11n/ac/p signal for receiver test under static conditions 1, 2, 3 = Transmission antennas Tx1 to Tx3 4, 5, 6 = Weigthing factors w1 to w3 = Baseband output for receiving antenna Rx1 8.
Page 119: Remote Control Commands
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 6 Remote control commands The commands in this section are required to generate signals with the IEEE 802.11 WLAN options in a remote environment. We assume that the R&S SMBV100B has already been set up for remote operation in a network as described in the R&S SMBV100B documentation.
Page 120: Programming Examples
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Programming examples 6.1 Programming examples The following sections provide programming examples for the IEEE 802.11 WLAN options. The purpose of the examples is to present all commands for a given task. In real applications, you typically need only a subset of commands. The programming examples have been tested with a software tool which provides an environment for the development and execution of remote tests.
Page 121: Marker Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Programming examples :SOURce1:BB:WLNN:TRIGger:DELay:UNIT TIME :SOURce1:BB:WLNN:TRIGger:EXTernal:TDELay 0.00001 :SOURce1:BB:WLNN:TRIGger:EXTernal:RDELay? // ****************************************************************** // Configure trigger in single mode. Set the output of // the current waveform to the first sample after // the next trigger event. Execute the trigger. // ****************************************************************** :SOURce1:BB:WLNN:TRIGger:SEQuence SINGle :SOURce1:BB:WLNN:TRIGger:SLUNit SAMP...
Page 122: Clock Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 General commands 6.1.3 Clock settings Example: To configure clock settings // ****************************************************************** // Select internal clock. // ****************************************************************** :SOURce1:BB:WLNN:CLOCk:SOURce INTernal // ****************************************************************** // Alternatively select external clock. Set its mode and query // input frequency. // ****************************************************************** :SOURce1:BB:WLNN:CLOCk:SOURce EXT :SOURce1:BB:WLNN:CLOCk:MODE SAMP...
Page 123 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 General commands [:SOURce<hw>]:BB:WLNN:PRESet Sets the parameters of the digital standard to their default values (*RST values speci- fied for the commands). Not affected is the state set with the command SOURce<hw>:BB:WLNN:STATe. Example: SOURce:BB:WLNN:PRESet Usage: Event Manual operation: "Set to Default"...
Page 124 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 General commands [:SOURce<hw>]:BB:WLNN:SETTing:LOAD <Filename> Loads the selected file with IEEE 802.11 WLAN settings. The directory is set using command MMEM:CDIRectory. A path can also be specified, in which case the files in the specified directory are read. The file extension may be omitted. Only files with the file extension *.wlann will be loaded.
Page 125: Filter/Clipping Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Example: BB:WLNN:VERS? "Release D11.0" Queries the IEEE 802.11 WLAN version. Usage: Query only [:SOURce<hw>]:BB:WLNN:WAVeform:CREate <Filename> Creates a waveform using the current settings of the "WLAN" menu. The file name is entered with the command. The file is saved with the predefined file extension *.wv. The file name and the directory it is saved in are user-definable.
Page 126 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Level clipping is activated if is set to [:SOURce<hw>]:BB:WLNN:CLIPping:STATe Parameters: <Level> integer Range: 1 PCT to 100 PCT Increment: 1 PCT *RST: 100 PCT BB:WLNN:CLIP:LEV 80PCT Example: Sets the limit for level clipping to 80% of the maximum level. BB:WLNN:CLIP:STAT ON Activates level clipping.
Page 127 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings [:SOURce<hw>]:BB:WLNN:CLIPping:STATe <State> Activates level clipping (Clipping). The value is defined with [:SOURce<hw>]:BB: WLNN:CLIPping:LEVel, the mode of calculation with [:SOURce<hw>]:BB:WLNN: CLIPping:MODE. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:CLIP:STAT ON Activates level clipping.
Page 128 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Manual operation: "Roll Off Factor or BxT" on page 100 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:COSine <Cosine> Sets the roll-off factor for the cosine filter type. Parameters: <Cosine> float Range: 0 to 1 Increment: 0.01 *RST: Example: BB:WLNN:PAR:COS 0.35 Sets the roll-off factor to 0.35 for filter type cosine.
Page 129 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Parameters: <LPass> float Range: 0.05 to 2 Increment: 0.01 *RST: Example: BB:WLNN:FILT:PAR:LPAS 0.5 The cut of frequency factor is set to 0.5. Manual operation: "Cut Off Frequency Factor" on page 101 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASSEVM <LPassevm> Sets the cut off frequency factor for the Lowpass (EVM optimization) filter type.
Page 130 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Filter/clipping settings Example: BB:WLNN:PAR:RCOS 0.22 Sets the roll-off factor to 0. 22 for filter type root cosine. Manual operation: "Roll Off Factor or BxT" on page 100 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:SPHase <SPhase> Sets B x T for the Split Phase filter type. Parameters: <SPhase>...
Page 131: Trigger Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings Parameters: <Variation> float Range: 400 to 40000000 Increment: 0.001 *RST: 20000000 Default unit: Hz (c/s) Example: BB:WLNN:SRAT:VAR 4000000 Sets the output sample rate to 4 MHz. Manual operation: "Sample Rate Variation" on page 101 6.4 Trigger settings Example: Configure and enable triggering SOURce1:BB:WLNN:TRIGger:SEQuence SINGle...
Page 132 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings SOURce1:BB:WLNN:TRIGger:DELay:UNIT TIME SOURce1:BB:WLNN:TRIGger:EXTernal:TDELay 0.00001 SOURce1:BB:WLNN:TRIGger:EXTernal:RDELay? // Response: 0.00001 SOURce1:BB:WLNN:TRIGger:DELay:UNIT SAMP SOURce1:BB:WLNN:TRIGger:EXTernal:DELay 10 ............132 [:SOURce<hw>]:BB:WLNN:TRIGger:ARM:EXECute ..............132 [:SOURce<hw>]:BB:WLNN:TRIGger:EXECute .........133 [:SOURce<hw>]:BB:WLNN:TRIGger:EXTernal:SYNChronize:OUTPut ..............133 [:SOURce<hw>]:BB:WLNN:TRIGger:RMODe? ..............133 [:SOURce<hw>]:BB:WLNN:TRIGger:SLENgth ..............134 [:SOURce<hw>]:BB:WLNN:TRIGger:SLUNit ..............134 [:SOURce<hw>]:BB:WLNN:TRIGger:SOURce ............. 135 [:SOURce<hw>]:BB:WLNN:TRIGger[:EXTernal]:DELay .............
Page 133 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings [:SOURce<hw>]:BB:WLNN:TRIGger:EXTernal:SYNChronize:OUTPut <Output> Enables signal output synchronous to the trigger event. Parameters: <Output> 1 | ON | 0 | OFF *RST: Manual operation: "Sync. Output to External Trigger/Sync. Output to Trigger" on page 107 [:SOURce<hw>]:BB:WLNN:TRIGger:RMODe? The command queries the current status of signal generation for all trigger modes with IEEE 802.11 WLAN modulation on.
Page 134 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings Manual operation: "Signal Duration" on page 105 [:SOURce<hw>]:BB:WLNN:TRIGger:SLUNit <Slunit> Defines the unit for the entry of the length of the signal sequence ([:SOURce<hw>]: BB:WLNN:TRIGger:SLENgth) to be output in the single trigger mode is set to SINGle).
Page 135 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings Manual operation: "Trigger Source" on page 107 [:SOURce<hw>]:BB:WLNN:TRIGger[:EXTernal]:DELay <Delay> Sets the trigger delay. Parameters: <Delay> float Range: 0 to 2147483647 Increment: 0.01 *RST: Default unit: samples Example: Example "Configure and enable triggering" on page 131.
Page 136 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Trigger settings [:SOURce<hw>]:BB:WLNN:TRIGger:TIME:DATE <Year>, <Month>, <Day> Sets the date for a time-based trigger signal. For trigger modes single or armed auto, you can activate triggering at this date via the following command: SOURce<hw>:BB:<DigStd>:TRIGger:TIME:STATe <DigStd> is the mnemonic for the digital standard, for example, ARB. Time-based trig- gering behaves analogously for all digital standards that support this feature.
Page 137: Marker Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Marker settings Specify the trigger date and trigger time with the following commands: SOURce<hw>:BB:<DigStd>:TRIGger:TIME:DATE SOURce<hw>:BB:<DigStd>:TRIGger:TIME:TIME <DigStd> is the mnemonic for the digital standard, for example, ARB. Time-based trig- gering behaves analogously for all digital standards that support this feature. Parameters: <State>...
Page 138 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Marker settings FAPart Number of Frame Blocks = 1, that is, a marker signal is gener- ated to mark every active part of each frame. The active data transfer part (PPDU) of a frame period is marked with high, the inactive part (idle time) with low.
Page 139 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Marker settings Parameters: <FbIndex> integer Range: 0 to 100 Increment: 1 *RST: Example: BB:WLNN:TRIG:OUTP1:FBIN 5 Sets the frame block index to 5. Manual operation: "Marker Mode" on page 109 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FINDex <FIndex> Sets the frame index, that is, the frame to be marked in the frame block marked with [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:FBINdex.
Page 140 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Marker settings Parameters: <Shift> integer Range: -1000 to 1000 *RST: Example: BB:WLNN:TRIG:OUTP2:RESH -20 shifts back the rising edge of marker 2 about 20 samples. Manual operation: "Marker Mode" on page 109 [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:PATTern <Pattern> Defines the bit pattern used to generate the marker signal if [:SOURce<hw>]:BB: WLNN:TRIGger:OUTPut<ch>:MODEis set to PATTern.
Page 141: Clock Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Clock settings [:SOURce<hw>]:BB:WLNN:TRIGger:OUTPut<ch>:PULSe:FREQuency? Queries the pulse frequency of the pulsed marker signal ([:SOURce<hw>]:BB: WLNN:TRIGger:OUTPut<ch>:MODEPULSe). The pulse frequency is derived by divid- ing the symbol rate by the divider. Return values: <Frequency> float Range: 0.0 to max Example: BB:WLNN:TRIG:OUTP:PULS:DIV 2 Sets the divider marker signal of the corresponding marker sig-...
Page 142: Antenna Configuration Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Antenna configuration settings Parameters: <Source> INTernal *RST: INTernal Example: BB:WLNN:CLOC:SOUR INT Selects an internal clock reference. Manual operation: "Clock Source" on page 114 6.7 Antenna configuration settings ..............142 [:SOURce<hw>]:BB:WLNN:ANTenna:MODE ..............142 [:SOURce<hw>]:BB:WLNN:ANTenna:SYSTem ......143 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:OUTPut:DESTination ........
Page 143 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Antenna configuration settings [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:OUTPut:DESTination <Destination> Selects the destination of the calculated IQ chains. Parameters: <Destination> OFF | BB | BB_B | FILE No mapping takes place. The IQ chain is output to the baseband A. Exactly one output stream can be mapped as "Baseband A".
Page 144 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Antenna configuration settings [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:IMAGinary <Imaginary> Sets the value for the Imaginary coordinate. Parameters: <Imaginary> float Range: -999.99 to 999.99 Increment: 0.01 *RST: BB:WLNN:ANT:TCH1:TX2:IMAG 500 Example: sets the imaginary coordinate for the selected transmission chain to 500. Manual operation: "Imaginary/Phase"...
Page 145: Frame Block Configuration
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration 6.8 Frame block configuration ..............145 [:SOURce<hw>]:BB:WLNN:FBLock:APPend ..............145 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:COPY ................145 [:SOURce<hw>]:BB:WLNN:CFBLock .............. 146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DELete ................146 [:SOURce<hw>]:BB:WLNN:DFBLock ................146 [:SOURce<hw>]:BB:WLNN:IFBLock ..............146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:INSert ..............146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PASTe ................146 [:SOURce<hw>]:BB:WLNN:PFBLock ............. 146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BCSMoothing ...............
Page 146 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DELete [:SOURce<hw>]:BB:WLNN:DFBLock <DfBlock> Deletes the selected frame block. Setting parameters: <DfBlock> integer Range: 1 to 100 Example: BB:WLNN:DFBL 10 deletes the selected frame block. Usage: Setting only [:SOURce<hw>]:BB:WLNN:IFBLock <IfBlock> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:INSert The command adds a default frame block before the selected frame block. Example: BB:WLNN:FBL2:INS inserts a default frame block before the selected frame block.
Page 147 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BOOSt <Boost> Assigns a specific RMS power boost/attenuation to the corresponding frame block modulation. The power level of a frame block modulation is calculated as sum of the power boost and the power level set in the header of the instrument. Note: At least one frame block should have a power boost set to 0 dB value for this gated power mode functionality to work properly.
Page 148 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration ZERO | ONE Internal 0 and 1 data is used. PATTern Internal data is used. The bit pattern for the data is defined by the command BB:WLNN:FBLocks:DATA:PATTern. AMPDU Aggregated mac protocol data unit (A-MPDU) data is used as configured with the commands in Chapter 6.9.4, "MPDU config- uration",...
Page 149 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:RATE? The command queries the PPDU data rate. Return values: <Rate> float Example: BB:WLNN:FBL5:DATA:RATE? queries the data rate. Usage: Query only Manual operation: "Data Rate /Mbps" on page 29 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:ITIMe <ITime> Sets the time interval separating two frames in this frame block.
Page 150 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame block configuration [:SOURce<hw>]:BB:WLNN:FBLock<ch>:STANdard <Standard> Sets the IEEE 802.11 WLAN standard. Parameters: <Standard> USER | WAG | WBG | WPJ | WN | WAC | WAX | WBE USER Sets a user defined standard. Sets the IEEE 802.11a/g standard.
Page 151: Frame Configuration Settings
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <TMode> L20 | LDUP | LUP | LLOW | HT20 | HT40 | HTDup | HTUP | HTLow | CCK | PBCC | V20 | V40 | V80 | V160 | V8080 | L10 | S1 | S2 | S4 | S16 | HE20 | HE40 | HE80 | HE8080 | HE160 | EHT320 | EHT20 | EHT40 | EHT80 | EHT160 | EHT320 *RST:...
Page 152 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings ........153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:RATE ............ 153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:RATE ........154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:TYPE ............ 154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:TYPE ..........154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:DCM ......154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:BPSymbol? ..........154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:BPSymbol? ...........154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:DCYCle? ............ 155 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:FDELay ..........155 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:FDURation? ........155 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:LENGth .............155 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:LENGth ........
Page 153: [:Source]:Bb:wlnn:fblock[:User]:Coding:rate
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings ........... 167 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:TDWindowing:STATe ..............167 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:TTIMe ..............167 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:UINDex [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CBINonht <CBINonht> (Available only for VHT Tx mode) The command is used to modify the first 7 bits of the scrambling sequence to indicate the duplicated bandwidth of the PPDU.
Page 154: [:Source]:Bb:wlnn:fblock[:User]:Coding:type
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:TYPE <Type> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:TYPE <Type> Selects the channel coding. Parameters: <Type> OFF | BCC *RST: Example: BB:WLNN:FBL5:COD:TYPE OFF no channel coding is used. Manual operation: "Channel Coding" on page 34 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:DCM <DCM> Enables dual carrier modulation.
Page 155: [:Source]:Bb:wlnn:fblock:Data:fdelay
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Example: SOURce1:BB:WLNN:FBLock1:DATA:DCYCle? Response: 1 The frame duration and the total signal length are equal. Usage: Query only Manual operation: "Duty Cycle" on page 60 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:FDELay <FrameDelay> Shifts the frame in time by the specified frame delay value. Parameters: <FrameDelay>...
Page 156: [:Source]:Bb:wlnn:fblock[:User]:Data:rate
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings The data length is related to the number of data symbols. Whenever the data length changes, the number of data symbols is updated and vice versa. Parameters: <Length> integer Range: 0 to Max *RST: 1024 (for LEGACY);...
Page 157: [:Source]:Bb:wlnn:fblock[:User]:Dpnseed:state
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Modifys the first 7 bits of the scrambling sequence to indicate if the transmitter is capa- ble of "Static" or "Dynamic" bandwidth operation. Parameters: <DBINonht> STAT | DYN | OFF STAT The transmitter is capable of static bandwidth operation.
Page 158: [:Source]:Bb:wlnn:fblock:Guard
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:GUARd <Guard> Selects which guard interval is used for the OFDM guard. In physical mode green field or legacy, only long guard intervals are possible. In this case, the field is read-only. GD08, GD16 and GD32 are available only for the IEEE 802.11ax standard.
Page 159: [:Source]:Bb:wlnn:fblock[:User]:Modulation
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL1:MCS MCS8 selects MCS8 as the coding scheme used for the spatial stream. Manual operation: "MCS" on page 34 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MODulation<st> <Modulation> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MODulation<st> <Modulation> Selects the modulation used for the spatial stream. Parameters: <Modulation>...

Page 160: [:Source]:Bb:wlnn:fblock:Ntps
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <NSTS> integer Range: 0 to Max *RST: Example: BB:WLNN:BB:WLNN:FBL1:MU2:NSTS 8.0 sets 8 space time streams for user 2. Manual operation: "Multi User MIMO Settings Table" on page 33 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:NTPS <NTPS> (Available only for VHT Tx mode) Indicates whether VHT AP allows VHT non-AP STAs in TXOP power save mode to enter during TXOP.
Page 161: [:Source]:Bb:wlnn:fblock:Plcp:lcbit:state
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Selects the packet type (PPDU format) with long or short PLCP (physical layer conver- gence protocol). Depending on the format selected, the structure, modulation and data rate of the PLCP preamble and header are modified. Parameters: <Format>...
Page 162: [:Source]:Bb:wlnn:fblock[:User]:Pnseed
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:PNSeed <PNSeed> Sets the PN seed. Use this setting, if you don't use the default PN seed. Parameters: <PNSeed> 24 bits | 24 bit Range: #H000001,24 to #H7FFFFF,24 *RST: #H000001,24 Example: SOURce1:BB:WLNN:FBL5:DATA PN9 Sets "PN9"...
Page 163: [:Source]:Bb:wlnn:fblock:Psdu:modulation
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL5:PMOD LEG sets the physical mode to LEGACY. BB:WLNN:FBL5:TMOD CCK sets the transport mode BB:WLNN:FBL5:PSDU:BRAT 2MBPS sets the PSDU bit rate BB:WLNN:FBL5:PSDU:BSPR:STAT ON enables spreading Manual operation: "Barker Spreading" on page 36 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PSDU:MODulation? (available only for CCK and PBCC Tx modes) Queries the modulation type.
Page 164: [:Source]:Bb:wlnn:fblock[:User]:Scrambler:pattern
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings RANDom (not for CCK/PBCC) The scrambler is activated. The initialization value of the scrambler is selected at random. Each frame has a different random initialization value. This value is also different in case of successive recalculations with the same setting parameters so that different signals are generated for each calculation.
Page 165: [:Source]:Bb:wlnn:fblock:Segment
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "Right 106-Tone RU" on page 41 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SEGMent <SEGMent> Selects one of the two segments in VHT-80+80 MHz mode with transmission band- width 80 MHz or 160 MHz. Both segments can only be generated with bandwidth 160 MHz.
Page 166: [:Source]:Bb:wlnn:fblock:Sstream
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL:SMO ON switches on smoothing. Manual operation: "Smoothing" on page 62 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SSTReam <SStream> Sets the number of the spatial streams. For physical mode LEGACY, only value 1 is valid. For Tx Mode "HT-Duplicate", only value 1 is valid. In all other cases, the number of spatial streams depends on the number of antennas configured with command SOURce:BB:WLNN:ANTenna:MODE.
Page 167 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:TDWindowing:STATe <State> Activates/deactivates the time domain windowing. Time domain windowing is a method to influence the spectral characteristics of the signal, which is not stipulated by the standard. However, it does not replace oversampling and subsequent signal filtering. Parameters: <State>...
Page 168: Eht/He Configuration
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings 6.9.2 EHT/HE configuration ..............168 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BCHG ..............168 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BDCM ............... 169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BEUL? ..............169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BMCS ............169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BSSColor ............... 170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BWINd ........170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:RUALlocation<st> ........171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:RUALlocation<st> ............171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CURPe? ............171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DOPPler ..............171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:EMCS .............
Page 169 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "SIG-B DCM" on page 41 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BEUL? Queries the total number of users for each 802.11be frame block. Return values: <UserLength> integer *RST: Example: BB:WLNN:FBLock2:BEUL? // Response: "8" // Frame block two has eight users. Usage: Query only Manual operation:...
Page 170 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL1:BSSC 5 Sets the BSS color to 5. Manual operation: "BSS Color" on page 42 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BWINd <BwType> Sets the type of channelization of 320 MHz channels in the BW field of the U-SIG-1 field.
Page 171 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:RUALlocation<st> <RuAllocation> For EHT frames. Sets the resource unit allocation of the second content channel for the respective channel and station. Parameters: <RuAllocation> RU0 | RU1 | RU2 | RU3 | RU4 | RU5 | RU6 | RU7 | RU8 | RU9 | RU10 | RU11 | RU12 | RU13 | RU14 | RU15 | RU16 | RU17 | RU18 | RU19 | RU20 | RU21 | RU22 | RU23 | RU24 | RU25 | RU26 | RU27 | RU28 | RU29 | RU30 | RU31 | RU32 | RU33 |...
Page 172 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <EhtSigMcs> MCS0 | MCS1 | MCS3 | MCS15 *RST: MCS0 Example: BB:WLNN:FBLock1:EMCS MCS1 // Sets modulation coding scheme MCS1. Manual operation: "EHT-SIG MCS" on page 48 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:ESDiffer <EHTSIGDiffer> For EHT-160MHz/EHT-320MHz frames, activates different EHT-SIG fields for every 80 MHz channel.
Page 173 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:LOGGing <LoggingState> If enabled (ON), the contents of HE-SIG-A and HE-SIG-B fields are written to a file in a text form. The location of the file can be queried with [:SOURce<hw>]:BB:WLNN: FBLock<ch>:LOGGing.
Page 174 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat <PpduFormat> Sets the PPDU format. Parameters: <PpduFormat> SU | MU | SUEXt | TRIG HE SU (single-user) carries a single PSDU. The HE Signal A (HE-SIG-A) field is not repeated. HE MU (multi-user) carries multiple PSDUs to one or more users.
Page 175 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings BW4|BW5 Sets the bandwidth mode for HE80 channels. BW6|BW7 Sets the bandwidth mode for HE8080 channels. *RST: Example: [:SOURce<hw>]:BB:WLNN:FBLock<ch>: on page 175. PPUNcturing:STATe Manual operation: "Preamble Puncturing Bandwidth" on page 43 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PPUNcturing:STATe <PreamblePunc>...
Page 176: User Configuration
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <SpatialReuse> integer Range: 0 to 15 *RST: Example: SOURce1:BB:WLNN:FBLock1:SPAReuse1 0 // Spatial reuse is not allowed for frame block 1. SOURce1:BB:WLNN:FBLock1:SPAReuse1 1 // Spatial reuse is not allowed for frame block 1. Manual operation: "Spatial Reuse 1/2"...
Page 177 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings ..........179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:RUTYpe ..........179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STAid ..........179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STATe ..........180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:TXBF [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:RUSelection<st> <RuSelCh1> For HE frames. Sets the resource unit allocation of the first content channel for the respective channel and station. Parameters: <RuSelCh1>...
Page 178 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:MUNum<st> <MuNumCh1> Sets the number of MU-MIMO users for each RU and station of the first content chan- nel. Parameters: <MuNumCh1> integer Range: 0 to 8 *RST: Manual operation: "Number of MU-MIMO users" on page 53 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CENRu<st>...
Page 179 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Usage: Query only Manual operation: "MU MIMO" on page 56 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:NSTS <UserNsts> Sets the number of spatial streams, the number of space time streams minus 1. Parameters: <UserNsts> integer Range: 1 to 8 *RST: Manual operation: "Nsts"...
Page 180: Mpdu Configuration
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <UserState> 1 | ON | 0 | OFF *RST: Manual operation: "State" on page 56 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:TXBF <TXBF> If switched on, indicates that the beamforming matrix is applied to the waveform. Parameters: <TXBF>...
Page 181 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings The lists are saved as files with the fixed file extensions *.dm_iqd in a directory of the user's choice. Parameters: <Filename> string Example: BB:WLNN:FBL1:MPDU1:DATA DLIS Selects the Data Lists data source. MMEM:CDIR '/var/user/temp/Lists' Selects the directory for the data lists.
Page 182: Mac Header Configuration
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:SOURce <Source> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:SOURce <Source> Selects the data source. Parameters: <Source> ZERO | ONE | PATTern | PN9 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt PNxx The pseudo-random sequence generator is used as the data source.
Page 183 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings ........... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol ......185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:FDS ..........185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:FDS ...... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:MDATa ........185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MDATa ..... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:MFRagments ....... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MFRagments ...... 185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:ORDer ........185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:ORDer ...185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:PMANagement ......185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PMANagement ....185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:PVERsion ........185...
Page 184 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:ADDRess<st> <Address> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:ADDRess<st> <Address> The command enters the value of the address fields 1 ... 4. Exactly 48 bits must be entered. Each address is 6 bytes (48 bit) long. The addresses can be entered in hexa- decimal form in the entry field of each address field.
Page 185 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:BSSid <Bssid> Sets the value of the basic service set identification (BSSID) field. Parameters: <Bssid> integer Example: BB:WLNN:FBL1:MAC:BSS #H124836C7EA54,48 Sets the value of the BSSID field to 124836C7EA54 Manual operation: "BSSID (hex)" on page 68 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol <FControl>...
Page 186 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:RETRy <Retry> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:SUBType <Subtype> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:SUBType <Subtype> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:TDS <Tds> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TDS <Tds> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:TYPE <Type> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TYPE <Type> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:WEP <Wep> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:WEP <Wep> The command enters the value of the individual bits of the frame control field. Parameters: <Wep>...
Page 187 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:QSControl <QsControl> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:QSControl <QsControl> Sets the value for the QoS control field. Parameters: <QsControl> integer Range: #H0000,16 to #HFFFF,16 Example: BB:WLNN:FBL1:MAC:QSC #H5A5A,16 Sets the value for the QoS field to#H5A5A,16. Manual operation: "QoS Control"...
Page 188 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:SCONtrol:FRAGment: STARt <Start> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SCONtrol:FRAGment:STARt <Start> The command enters the start number of the fragment bits of the sequence control. Parameters: <Start> integer Range: #H0,4 to #HF,4 *RST: #H0,4 Example: BB:WLNN:FBL1:MAC:SCON:FRAG:STAR #H4,4 sets the start value of the fragment bits of the sequence control.
Page 189 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:SCONtrol:STATe <State> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:SCONtrol:STATe <State> The command activates/deactivates the sequence control. Parameters: <State> 0 | 1 | OFF | ON *RST: Example: BB:WLNN:FBL1:MAC:SCON:STAT ON activates the sequence control field. Manual operation: "Sequence Control" on page 68 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:STATe <State>...
Page 190 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Parameters: <HtControl> integer Range: #H00000000,32 to #HFFFFFFFF,32 *RST: #H00000000,32 Example: BB:WLNN:FBL1:MAC:HTC #H5a5a5a5a,32 Sets the value for the HT control field to #H5a5a5a5a,32. Manual operation: "HT/VHT/HE Control" on page 72 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:ACConstraint <AcConstraint> Sets the value for the AC signal field.
Page 191 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CALibration:SEQuence <Sequence> Sets the value for the calibration sequence. Parameters: <Sequence> integer Range: #H0,2 to #H3,2 Example: BB:WLNN:FBL1:MAC:HTC:CAL:SEQ #H3,2 Sets the value for the calibration sequence. Manual operation: "Calibration Sequence" on page 74 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CSISteering <CsiSteering>...
Page 192 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "Reserved" on page 74 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:VHTControl: HVINdicator? [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:HVINdicator? The command queries the used format (HT or VHT). Return values: <HTVHT> integer Example: BB:WLNN:FBL:MAC:HTC:HVIN? Response: 1 HT format is used. Usage: Query only Manual operation: "HT/VHT"...
Page 193 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "Link Adaption Control" on page 74 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:NDP <Ndp> Sets the value of the Null Data Packet (NDP) announcement. 0 = no NDP will follow 1 = NDP will follow Parameters: <Ndp>...
Page 194 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:SREServed <Reserved> This signal field is currently defined, but not used. Parameters: <Reserved> integer Manual operation: "Reserved" on page 74 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:HTControl:STATe <State> [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:STATe <State> The command enables/disables HT Control. Parameters: <State> 0 | 1 | OFF | ON *RST: Example:...
Page 195 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings .........198 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:RDGMore ........198 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:UMFB ......199 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:VREServed [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl <VHTContol> The command sets the value for the VHT control field. Parameters: <VHTContol> integer Range: #H00000000,32 to #HFFFFFFFF,32 *RST: #H00000000,32 Example: BB:WLNN:FBL1:MAC:VHTC #H5a5a5a5a,32 sets the value for the VHT control field.
Page 196 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "Coding Type" on page 77 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:FTTYpe <FbTxType> The command sets the FB Tx Type subfield. 0 = If the Unsolicited MFB subfield is set to 1 and FB Tx Type subfield is set to 0, the unsolicited MFB refers to either an unbeamformed VHT PPDU or transmit diversity using an STBC VHT PPDU.
Page 197 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:MFB <Mfb> The command sets the MFB subfield. This subfield contains the recommended MFB. The value of MCS=15 and VHT N_STS=7 indicates that no feedback is present. See also Table 3-10 for definition of the MFB subfield.
Page 198 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:MSI <Msi> The command sets the MSI subfield. MRQ = 0 When the MRQ subfield is set to 0, the MSI subfield is reserved. MRQ = 1 When the MRQ subfield is set to 1, the MSI subfield contains a sequence number in the range 0 to 6 that identifies the specific request.
Page 199 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings if the MFB is not a response to an MRQ. Example: BB:WLNN:FBL:MAC:VHTC:UMFB #B1,1 sets the information for the UMFB subfield. Manual operation: "Unsolicited MFB" on page 76 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:VHTControl:VREServed <VhtReserved> This signal field is currently defined, but not used. It is set to zero by the transmitter and ignored by the receiver.
Page 200 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Return values: <HEIndicator> integer Usage: Query only Manual operation: "HE" on page 79 6.9.5.5 Trigger frame settings ......201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:BW ..... 201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CINDication ..... 201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CSRequired ....201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:DOPPler ....201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:EREServed .......201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:GILTf .....201...
Page 201 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:BW <BW> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: CINDication <CascadeInd> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: CSRequired <CSRequired> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:DOPPler <Doppler> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: EREServed <EhtReserved> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:GILTf <GILTF> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:HEEHt <HeEhtP160> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: HREServed <HESIGAReserved> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LEN <Length> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LESSeg <LDPCExtSymSeg> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:MLTFmode <MUMIMOLTFMode> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:NHLSym <NumHeLtfSym> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo: PEXTension <PacketExtension> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:RSV <Reserved>...
Page 202 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: CODType <CodingType> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>:DCM <DCM> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>:MCS <MCS> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: PS160 <PS160> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>:PVI <PhyVerId> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>:RSV <Reserved> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: RUALlocation <RUAllocation> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: SPRFirst <SpatialReuse1> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: SPRSecond <SpatialReuse2> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: SSALlocation <SSAllocation> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: TDUSerinfo <TrigDepUserInfo> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: TRSSi <TargetRssi> [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:UINFo<st0>: UBEXtension <UlBandExt>...
Page 203 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings End of frame is tagged. *RST: Example: SOURce1:BB:WLNN:FBLock1:TFConfig:EOF E1 The end of the trigger frame in the first frame block is tagged. Manual operation: "MPDU EOF" on page 95 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:PADLength <PaddingLength> Queries the length of the padding field in the trigger frame.
Page 204: Beacon Configuration
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings 6.9.6 Beacon configuration 6.9.6.1 General beacon functions ........204 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:BINTerval ......204 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:DCCHannel? ........204 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:IAWindow ........205 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:SRATe ......... 205 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:SSID ........205 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:TSTamp [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:BINTerval <BInterval> Defines the time interval between two beacon transmissions. Parameters: <BInterval>...
Page 205 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Manual operation: "IBSS(ATIM Window) (hex)" on page 81 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:SRATe <SRATe> Determines a set of data rates that are supported by the access point (Supported Rates field). Parameters: <SRATe> integer Example: BB:WLNN:FBL1:BFC:SRAT #H06090C1218243036,64 Determines the following set of supported data rates: Hex num- bers 06 09 0C 12 18 24 30 36.
Page 206 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings ...... 208 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:DBACk ..... 208 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:DOFDm ......208 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:PBCC .....208 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:PRIVacy ......209 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:QOS ...209 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:RMEasurement ...... 209 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:SMGMt ....209 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:SPReamble ......210 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:SSTime ....210 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:HTCapability:GFIeld ....210 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:HTCapability:STATe [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:APSD <CAPSd> Informs the associated stations if automatic power save delivery (APSD, energy saving function) is supported.
Page 207 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:CPRequest <CCPRequest> Indicates if contention free poll (CF-poll) is requested. Parameters: <CCPRequest> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL1:BFC:CAP:CPR ON Tells the associated stations that contention free poll (CF-poll) is requested.
Page 208 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:DBACk <CDBAck> Informs the associated stations if delayed block Ack is allowed. Parameters: <CDBAck> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL1:BFC:CAP:DBAC ON Informs the associated stations that delayed block Ack is allowed.
Page 209 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:QOS <QOS> Informs the associated stations if quality of service (QoS) is supported. Parameters: <QOS> 1 | ON | 0 | OFF *RST: Example: SOUR:BB:WLNN:FBL1:BFC:CAP:QOS ON Informs the associated stations that quality of service (QoS) is supported.
Page 210 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:CAPability:SSTime <SSTime> Informs the associated stations if short slot time is supported. Parameters: <SSTime> 1 | ON | 0 | OFF *RST: Example: BB:WLNN:FBL1:BFC:CAPability:SST ON Informs the associated stations that short slot time is supported. [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:HTCapability:GFIeld <GreenField>...
Page 211: Spatial Mapping Configuration
® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL1:BFC:ERP:BPM ON Informs associated stations that they should use the long pream- ble. [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:ERP:NEPResent <ENEPresent> Sets Non-ERP Present on. This is needed if there is a non-ERP MU associated to the Parameters: <ENEPresent>...
Page 212 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings DIRect (only active with physical modes MIXED MODE or GREEN FIELD when N The transmit matrix is a CSD matrix, that is, diagonal matrix of unit magnitude and complex values that represent cyclic shifts in the time domain.
Page 213 ® Remote control commands R&S SMBVB-K54/-K86/-K142/-K147 Frame configuration settings Example: BB:WLNN:FBL1:SMAP:IND 30 Sets the index of the subcarrier to k = 30. Manual operation: "Index k" on page 97 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:SMAPping:ROW<st>:COL<dir>:I? Queries the time shift value of element I of the selected row and column of the spatial transmit matrix.
Page 214: Glossary: Specifications And References
® Glossary: Specifications and references R&S SMBVB-K54/-K86/-K142/-K147 Glossary: Specifications and references Symbols 1GP56: Rohde & Schwarz application note "IEEE 802.11 Packet Error Rate Testing": https://www.rohde-schwarz.com/appnote/1GP56.html 1GP94: Rohde & Schwarz application note "Generating Signals for WLAN IEEE 802.11ac": https://www.rohde-schwarz.com/appnote/1GP94.html 1GP115: Rohde & Schwarz application note "Generating WLAN IEEE 802.11ax Sig- nals": https://www.rohde-schwarz.com/appnote/1GP115.html 1MA69: Rohde &...
Page 215: List Of Commands
® List of commands R&S SMBVB-K54/-K86/-K142/-K147 List of commands [:SOURce<hw>]:BB:WLNN:ANTenna:MODE....................142 [:SOURce<hw>]:BB:WLNN:ANTenna:SYSTem.....................142 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:OUTPut:DESTination........... 143 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:OUTPut:FSELect............143 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:IMAGinary............144 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:MAGNitude............. 144 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:PHASe............144 [:SOURce<hw>]:BB:WLNN:ANTenna:TCHain<ch>:TX<dir>:REAL.............. 143 [:SOURce<hw>]:BB:WLNN:BWidth....................... 122 [:SOURce<hw>]:BB:WLNN:CFBLock......................145 [:SOURce<hw>]:BB:WLNN:CLIPping:LEVel....................125 [:SOURce<hw>]:BB:WLNN:CLIPping:MODE....................126 [:SOURce<hw>]:BB:WLNN:CLIPping:SPPState................... 126 [:SOURce<hw>]:BB:WLNN:CLIPping:STATe....................127 [:SOURce<hw>]:BB:WLNN:CLOCk:SOURce....................141 [:SOURce<hw>]:BB:WLNN:DFBLock......................146 [:SOURce<hw>]:BB:WLNN:FBLock:APPend....................145 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BCHG................... 168 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BCSMoothing................146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BDCM...................168 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BEUL?..................
Page 216 ® List of commands R&S SMBVB-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BFConfiguration:TSTamp............. 205 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BMCS................... 169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BOOSt..................147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BSSColor..................169 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:BWINd..................170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CBINonht..................153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:MUNum<st>..............178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:RUALlocation<st>..............170 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH1:RUSelection<st>..............177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:MUNum<st>..............177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:RUALlocation<st>..............171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CCH2:RUSelection<st>..............177 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CENRu<st>.................. 178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:ENCoder?...............153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:RATE................153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CODing:TYPE................154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:COPY................... 145 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:CURPe?..................171 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA.................... 147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:BPSymbol?................ 154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:DCYCle?................154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:DATA:DSELection................
Page 217 ® List of commands R&S SMBVB-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:MFRagments............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:ORDer..............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PMANagement............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:PVERsion............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:RETRy..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:SUBType............. 186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TDS..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:TYPE..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCONtrol:WEP..............186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:FCS:STATe................186 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl................189 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:ACConstraint............190 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CALibration:POSition......... 190 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CALibration:SEQuence........191 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:CSISteering............191 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:FREQuest............191 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:HVINdicator?............192 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:LAControl............192 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:NDP..............193 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:RDGMore............193 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:REServed............193 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:SREServed............194 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:STATe..............194 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:HTControl:ZLF..............194 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:QSControl................187 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MAC:QSControl:STATe..............
Page 218 ® List of commands R&S SMBVB-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU:EOF.................. 182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:DSELection............180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:LENGth............181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:PATTern............181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MPDU<st>:DATA:SOURce............182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MU<st0>:GID................159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MU<st0>:NSTS................159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:MUMimo:STATe................159 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:NONOfdmaUser................173 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:NTPS....................160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PAID:PATTern................160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PASTe...................146 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PED?.................... 173 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFORmat..................174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PFPFactor?.................. 174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PLCP:FORMat................160 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PLCP:LCBit:STATe...............161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PMODe..................149 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:POFDma..................174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PPUNcturing.................174 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PPUNcturing:STATe..............175 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PPUNcturing:SUBC<di>:STATe........... 175 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PREamble:STATe.................161 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:PSDU:BRATe................
Page 219 ® List of commands R&S SMBVB-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:DCM................154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:GAIN................178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:MRUindex..............178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:MUMimo:STATe?............178 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:NSTS................179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:RUTYpe..............179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STAid................179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:STATe................. 179 [:SOURce<hw>]:BB:WLNN:FBLock<ch>:USER<di>:TXBF................180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:ENCoder?...........153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:RATE............153 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:CODing:TYPE............154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:BPSymbol?............ 154 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:LENGth............155 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:RATE?............156 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DATA:SYMBols............156 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:DPNSeed:STATe............157 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:ILEaver:STATe............158 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:ADDRess<st>..........184 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:ADDRess<st>:STATe........184 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:DID..............184 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol............185 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MAC:FCONtrol:FDS..........
Page 220 ® List of commands R&S SMBVB-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU:EOF.............. 182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:DSELection........180 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:LENGth........181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:PATTern........181 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:MPDU<st>:DATA:SOURce........182 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:PNSeed..............162 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:MODE........... 163 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SCRambler:PATTern..........164 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:SERVice:PATTern.............165 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:BW..........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CINDication........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:CSRequired........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:DOPPler........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:EREServed........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:GILTf..........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:HEEHt........... 201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:HREServed........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LEN..........201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:LESSeg......... 201 [:SOURce<hw>]:BB:WLNN:FBLock<ch>[:USER<di>]:TFConfig:CINFo:MLTFmode........
Page 221 ® List of commands R&S SMBVB-K54/-K86/-K142/-K147 [:SOURce<hw>]:BB:WLNN:FILTer:IUPSampling...................127 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:APCO25................127 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:COSine................128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:COSine:COFS..............128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:GAUSs................128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASs..................128 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:LPASSEVM................. 129 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:PGAuss................129 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:RCOSine................129 [:SOURce<hw>]:BB:WLNN:FILTer:PARameter:SPHase................130 [:SOURce<hw>]:BB:WLNN:FILTer:TYPE...................... 130 [:SOURce<hw>]:BB:WLNN:IFBLock......................146 [:SOURce<hw>]:BB:WLNN:PFBLock......................146 [:SOURce<hw>]:BB:WLNN:PRESet......................123 [:SOURce<hw>]:BB:WLNN:SETTing:CATalog?.................... 123 [:SOURce<hw>]:BB:WLNN:SETTing:DELete....................123 [:SOURce<hw>]:BB:WLNN:SETTing:LOAD....................124 [:SOURce<hw>]:BB:WLNN:SETTing:STORe....................124 [:SOURce<hw>]:BB:WLNN:SRATe:VARiation....................130 [:SOURce<hw>]:BB:WLNN:SRATe?......................130 [:SOURce<hw>]:BB:WLNN:STATe........................ 124 [:SOURce<hw>]:BB:WLNN:TRIGger:ARM:EXECute..................132 [:SOURce<hw>]:BB:WLNN:TRIGger:EXECute.....................
Page 222: Index
® Index R&S SMBVB-K54/-K86/-K142/-K147 Index Documentation overview ............. 9 Doppler ................43 AC constraint ..............73 Duty cycle ................60 VHT ................76 Dynamic bandwidth in non HT .......... 60 Addresses ................. 67 Aggregated control ............79 Antennas ................21 Application cards ............... 10 320 MHz type ..............
Page 223 ® Index R&S SMBVB-K54/-K86/-K142/-K147 Group ID ................33 Nyquist filter ..............100 Guard ..............35, 40, 50 OFDMA mode ..............48 Open source acknowledgment (OSA) ....... 10 Current PE duration ............ 41 Output ................22 LTF symbol duration ..........41, 50 Output file ..............
Page 224 ® Index R&S SMBVB-K54/-K86/-K142/-K147 Single ................105 RDG/More PPDU ............76 Smoothing ................. 62 Reserved ..............78 Space time block coding ........... 32 Unsolicited MFB ............76 Space time streams ............ 31, 33 Videos ................11 Spatial mapping mode ............97 Spatial reuse ...............

This manual is also suitable for:

R&s smbvb-k86 R&s smbvb-k142 R&s smbvb-k147

Rohde & Schwarz R&S SMBVB-K54 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Rohde & Schwarz R&S SMBVB-K54

Summary of Contents for Rohde & Schwarz R&S SMBVB-K54

This manual is also suitable for:

Table of Contents