Table of Contents
Advertisement
H. Repositioning the Camera when Mounting the E-50 Horizontal
(Requires Viking model LB-50 Camera L-Bracket - not included with the E-50)
When mounting the E-50 to 4 inch or less horizontal lap siding, the unit can be mounted horizontally. When doing so, the internal
video camera will have to be repositioned (vertically rotated 90 degrees) to correct the video image orientation. An additional cam-
era "L" bracket (Viking model LB-50) is required to reposition the camera. To purchase LB-50 contact your local Viking distributor.
To install the LB-50, remove the bottom #2 screw and lock washer which fastens the camera "U" bracket to the circuit board mount-
ing plate. Remove the two screws mounting the camera to the "U" bracket. Rotate the camera 180 degrees so the video output wires
exit the lower back plate of the camera and refasten it to the "U" bracket. Use the #2 screw and lock washer to attach the LB-50 "L"
bracket to the mounting plate then attach the camera to the "L" bracket with the screw and lock washer supplied with the LB-50 as
shown in the diagram. Note: Mounting the E-50 horizontally will reduce the camera horizontal adjustment to +/- 20 degrees and
increase the vertical tilt to +/- 30 degrees.
* Caution: When mounting the camera horizontally on a model E-50-EWP, the single gang rough in box may require trimming to
allow room for the new camera position.
P
r
o
g
r
a
m
m
P
r
o
g
r
a
m
m
A. Adjusting Speaker Volume
The speaker volume pot can be adjusted to increase or
decrease the speaker volume to the level desired.
B. Adjusting the Microphone Volume
In certain noisy locations (background traffic, machin-
ery or wind), the microphone volume may need to be
decreased. A symptom of this is one-way talk path, in
which the distant party cannot be heard over the
speaker. A microphone volume pot is provided for
increasing or decreasing the microphone volume.
Note: If the microphone volume is set too high or too
low, one-way talk path may occur.
C. DIP Switch Programming
1. Auto Answer Feature ON/OFF (DIP Switch 1)
DIP switch 1 is for turning the Auto Answer feature ON and OFF.
The E-50 is factory set to auto answer when an inbound call is
detected
.
2. Dial Tone Detection ON/OFF (DIP Switch 2)
With DIP switch 2 in the ON position, if the E-50 detects more
than 5 seconds of continued dial tone, the unit will automatically
disconnect. If the E-50 is installed on a continuously noisy line, it
may detect the noise as dial tone and automatically disconnect. If
this happens, turn the dial tone detection (DIP switch 2) OFF.
3. Programming Mode ON/OFF (DIP Switch 3)
With DIP switch 3 in the OFF position, the E-50 is in the "Normal Operation Mode" (factory setting). By placing DIP
switch 3 in the ON position, the E-50's programming mode is enabled. The programming mode is used for adjust-
ing the Call Length Time Out, Silence Time for automatic disconnect and the Talk/Listen delay (VOX switching
speed). These features are set from the factory and normally do not need adjustment. If adjustment is necessary,
see Programming sections D - I.
6
i
n
g
i
n
g
Standard E-50:
"L" Bracket (LB-50)
"U" Bracket
Circuit Board
Mounting Plate
#2 x 3/16" panhead screws and
#2 lock washer (typ. 4 places)
Microphone
Volume
(see section B)
DIP
Switches
ON
ON
OFF
1 2 3
*E-50-EWP:
"L" Bracket (LB-50)
"U" Bracket
(see section A)
Rear View of the
E-50 Circuit Board
Mounting Plate
Note:
switches are shown in
factory default settings.
DIP
Position
Description
Switch
1
ON
Auto-Answer ON *
OFF
Auto-Answer OFF
1
ON
Dial Tone Detection ON *
2
OFF
Dial Tone Detection OFF
2
ON
Programming Mode
3
3
OFF
Normal Operation Mode *
* Note: These are the factory settings.
Speaker
Volume
Pots and DIP
Advertisement
Table of Contents
