Advertisement
System connections
Connection
to jacks
and
termi-
nals
@
@®
Strip about 10 mm
(3/8 inch) of insula-
together the bare
tion from the end of
strands of wire.
the wire.
®
®
®
¥
2,
Gi
Insert the connec-
Turn clockwise to
tion cord to a suffi-
secure the connec-
23/171} ——} }
Twist and solder
Loosen the terminal
by turning it coun-
terclockwise.
cient depth.
tion cord. Pull the
cord lightly to make
sure it is secured
tightly.
VS.
PHoKo
©©
Ole
©|
OGG
©oOwzOle
©| ©
OH
©
©| ©
ONC
©
©O
1©
Speaker
€
:
"Oe
ore
(e000
ui 2
ceRre si noc me ot
Amplifier
Connection
of CENTER
OUT jack
Speaker with
built-in amp
OOO
CE eg ONT PE
Woofer with
built-in amp
SUB
Amplifier
WOOFER
Connection
of SUB
WOOFER
jack
8
kA-v6000 (En)
@ Caution concerning speaker connections
1.
2.
Set the POWER
switch to OFF before connecting the
speaker cords.
After connecting the lead wires, verify that they do not
come into contact with other terminals.
. Never short-circuit the (+) and (~) speaker cords.
. Be sure
not
to inverse
the
left and
right speaker
connections or the (+) and (—) terminal polarity. This
will cause
the acoustic
image
of instruments
to be
unclear and the sound to be unnatural.
@ Speaker impedance
When
connecting
speakers
using
either
the
A
or
B
speaker terminals (not both), use speakers with an imped-
ance of 6-16 ohms.
When
connecting
speakers
using
both
the
A and
B
speaker
terminals,
use
speakers
with an
impedance
of
12-16
ohms.
In this case,
even
if one
speaker
has an
impedance of less than
12 ohms, damage to the amplifier
may occur.
H@ Connection
of CENTER
OUT jack
In addition to the CENTER
SPEAKERS terminals, a CEN-
TER OUT jack is provided on the rear panel of this unit. If
you use an optional amplifier or a speaker with built-in
amplifier, connect a speaker to this jack using an audio
cord.
Note:
The output at the CENTER OUT jack is the LINE output. In case
your speaker
does
not incorporate
an amplifier,
connect
the
CENTER
OUT
jack output
to the AUX
jack of an exclusive
amplifier, and connect the speaker to the amplifier connected to
the CENTER
OUT jack.
@ Connection
of FRONT
PRE OUT jacks
To
obtain
more
speaker
effect
with
larger
speakers,
connect the FRONT PRE OUT jacks to an optional power
amplifier and connect
the front speakers
to the power
amplifier.
@ Connection of REAR
PRE OUT jacks
The
surround
effect
can
be obtained
with
the built-in
amplifier.
To obtain
more
surround
effect
with
larger
speakers, connect the REAR PRE OUT jacks to an optional
power
amplifier
and
connect
the rear speakers
to the
power amplifier.
@ SUB WOOFER
jack connection
A SUB WOOFER
jack is provided on the rear panel of the
unit. When
connecting
a sub-woofer
or Super Woofer,
connect it to this jack using an audio cord.
Note:
The output at the SUB WOOFER
jack is the LINE output. If your
sub-woofer
or Super
Woofer
does
not
incorporate
a built-in
amplifier, connect the SUB WOOFER
jack output to a specialpur-
pose amplifier and
connect
the speaker
to the amplifier con-
nected to the SUB WOOFER
jack.
Advertisement
