Table of Contents
Advertisement
Basic Operation
6. INFORMATION
Displays monitor information.
INFORMATION1
INPUT MODE
SIZE
PICTURE MODE
BRIGHT
VOLUME
REMOTE No.
MODEL
VERSION
S/N
STATUS
TOUCH PANEL
3 8 4 0 x 2 1 6 0
V: 60 Hz
INFORMATION2
LAN PORT
DHCP CLIENT
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS
DNS PRIMARY
DNS SECONDARY
MONITOR NAME
MAC ADDRESS
3 8 4 0 x 2 1 6 0
V: 60 Hz
INFORMATION3
OPTION
POWER STATUS
MODULE
TYPE
INTERFACE VERSION
FORM FACTOR SIZE
MAX POWER
3 8 4 0 x 2 1 6 0
V: 60 Hz
The display changes from "INFORMATION1" →
"INFORMATION2" → "INFORMATION3" → disappears the
display, and so on every time you press this button.
When displaying "INFORMATION", the display changes from
"INFORMATION1" → "INFORMATION2" → "INFORMATION3"
→ "INFORMATION1", and so on every time you press the
button. Pressing the RETURN button disappears the display.
• "INFORMATION3" shows the information when you have
used the option board slot to expand the functions.
• The display disappears automatically after about 15
seconds.
7. FUNCTION
The ADMIN menu can also be displayed by pressing the
FUNCTION button and then the MENU button. (See page 32.)
8. ENTER
Confirms the setting.
9. FREEZE
Freezes the video shown on the monitor.
To cancel, press any button other than the POWER button,
MUTE button or VOLUME button.
Freeze is also canceled when the input signal changes
(switching to no signal, changing the resolution, etc.).
In some cases a residual image may occur. Do not freeze the
video for a long time.
24
E
:
HDMI1
:
WIDE
:
STD
:
31
:
15
:
0
:
PN-LA752
:
×.×.×.×
:
xxxxxxxx
:
0000-000000-00-0000
:
OK
NEXT:[ ]
END:[RETURN]
H: 135.0 kHz
:
OFF
:
XX-XX-XX-XX-XX-XX
NEXT:[ ]
END:[RETURN]
H: 135.0 kHz
:
NOT CONNECTED
:
- - - -
:
- - - -
:
- - - -
:
- - - -
:
- - - -
:
- - - -
NEXT:[ ]
END:[RETURN]
H: 135.0 kHz
10. Buttons for operating the HDMI-connected device
When "HDMI CEC LINK" is set to "AUTO", use these buttons
to operate the device connected through the HDMI interface.
11. ID SET
Set a number on the remote control unit. (See page 38.)
12. OPTION
Switch the input mode to OPTION when you have used the
option board slot to expand the functions.
13. DP
When "POWER SAVE MODE" is set to "OFF", each press of
the DP button alternates the input mode between DisplayPort
and USB-C.
14. SIZE (Screen size selection)
The menu is displayed.
Press the
or
button to select the screen size. (See page
25.)
15. PIP/PbyP
The menu is displayed.
Press the
or
button to select PIP MODES/
QUAD-SCREEN MODE. (See page 36.)
16. BRIGHT +/- (Brightness adjustment)
Pressing + or - displays the BRIGHT menu.
B R I G H T
Press + or - to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
* When "AMBIENT LIGHT SENSING" is set to "ON",
"AMBIENT LIGHT SENSING" is displayed even if you press
+ or -, and the brightness cannot be adjusted.
17. INPUT (Input mode selection)
The menu is displayed.
Press the
or
button to select the input mode, and press
the ENTER button to enter.
* For the input modes that can be selected, see "Using the
touch menu" (see page 22).
18. MENU
Displays and turns off the menu screen. (See page 26.)
19. Cursor
These buttons are used to perform operations such as
selecting items, changing adjustment values, and moving the
cursor.
20. RETURN
Returns to the previous screen.
15
Advertisement
Table of Contents
