E or by the safety earth • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. • The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician. “WARNING: THIS APPARATUS MUST BE EARTHED.” Authorised representative responsible for the European Union Community Market Model No.: Serial No.: FOR CUSTOMERS IN U.K. IMPORTANT GREEN-AND-YELLOW: BLUE: BROWN: or coloured green or green-and-yellow. SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg Earth Neutral Live U.S.A. ONLY...
IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch. B. Information on Disposal for Business Users 1. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the established collection system or your local authority for take-back of your used products. 2. In other Countries outside the EU If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.
SAFETY PRECAUTIONS (Continued) 1 9. B atteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • Use the specified batteries only. • I nstall the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the compartment. • Do not mix old and new batteries. • Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary. • Replace an exhausted battery with a new one promptly. • If you will not use the remote control for a long time, remove the batteries. • I f leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your clothing may cause a skin irritation or damage your eye.
- I llustrations in this manual may not exactly represent the actual product or display. - T his manual assumes use in horizontal orientation, except where specifically noted. LED Backlight ● The LED backlight in this product has a limited lifetime. * I f the screen gets dark or does not turn on, it may be necessary to replace the LED backlight. This LED backlight is exclusive to this product and must be replaced by an authorized Sharp servicing dealer or service center. * P lease contact your local Sharp servicing dealer or service center for assistance.
• When moving the monitor, be sure to hold it with either both handles or the 4 corners on the bottom of the unit. Do not place your hand on the screen. This may cause product damage, failure, or injury. • Install the monitor with the surface perpendicular to a level surface. • Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or mishandling. • This monitor should be used at an ambient temperature between 41°F (5°C) and 95°F (35°C). Provide enough space around the monitor to prevent heat from accumulating inside.
When the PN-ZB01 (optional) is attached Caution • Consult your SHARP dealer for attachment/detachment of optional parts. • Do not open the expansion terminal cover by yourself. There are high voltage parts inside the cover which may cause an electric shock. Part Names 1. Touch pen ultrasonic sensor 2. Infrared transmitter/receiver 3.
nRemote control unit 1. Signal transmitter 2. POWER button (See page 15.) 3. MUTE button (See page 18.) 4. VOL +/- buttons (See page 18.) BRIGHT +/- buttons (See page 18.) Cursor control ( 5. DISPLAY button (See page 18.) 6. MODE button (See page 18.) 7. INPUT button (See page 18.) 8. MENU button (See page 18.) 9. SIZE button (See page 18.) Part Names ) buttons...
Connecting Peripheral Equipment When the PN-ZB01 (optional) is attached Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may cause malfunctions and the other problems.
Connection when the PN-ZB01 (optional) is attached The PN-ZB01 expansion board (optional) allows the use of additional connection terminals. 6. PC/AV DVI-D input terminal • Set DVI of INPUT SELECT on the OPTION menu according to the device to be connected. • Select the audio input terminal to be used in PC DVI-D or AV DVI-D of AUDIO SELECT on the OPTION menu. 7. PC RGB input terminals • Set BNC of INPUT SELECT on the OPTION menu to PC RGB when using the PC RGB input terminals. • Select the audio input terminal to be used in PC RGB of AUDIO SELECT on the OPTION menu. 8. AV component input terminals • Set BNC of INPUT SELECT on the OPTION menu to AV COMPONENT when using the AV component input terminals.
Connecting the Power Cord Caution • Do not use a power cord other than the one supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. Cable Cable clamp attachment Cable clamp Handle screws Handle Main power switch Binding Cables The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.
Affixing the Stand Hole Protection Covers Preparing the Remote Control Unit Installing the batteries 1. Press the cover gently and slide it in the direction of the arrow. 2. See the instructions in the compartment and put in the supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and minus (-) sides oriented correctly. 3. Close the cover. TIPS • When the batteries become exhausted, replace them with new (commercially available) batteries. • The supplied batteries (R-6 (“AA” size) x 2) may become exhausted quickly depending on how they are stored. • If you will not be using the remote control for a long time, remove the batteries. • Use manganese or alkaline batteries only.
The touch pen, remote control unit, and eraser can be stored in the holder. Touch pen Remote control unit and Eraser Attaching the Holder 1. Remove the peel-off sheets from the fasteners on the back side of the holder. 2. With the holder spread taut, affix it to the side of the monitor. Back side...
Turning Power On/Off Caution • Turn on the monitor first before turning on the PC or playback device. Turning on the main power Main power switch Caution • The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on. • When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. • For a complete electrical disconnection, pull out the main plug. Turning power on/off Press the POWER button or POWER switch to turn the power ON/OFF.
If you already set the time but the date/time setting • screen appears when the power is turned on, the internal battery may be exhausted. Please contact your local Sharp servicing dealer or service center for assistance with battery replacement. Estimated service life of the internal battery: About 5 •...
Preparing and Using the Touch Pen Inserting the battery 1. Rotate the battery cap and remove it, and then pull out the cover. 2. Insert the supplied battery (LR-03 (“AAA” size)) in the orientation shown, and attach the cover and battery cap. TIPS • If the battery indicator does not illuminate when Function Button 1 or Function Button 2 is pressed, the battery is exhausted. Replace the battery with a new commercially available battery.
1. INPUT (Input mode selection) The menu is displayed. Press mode, and press to enter. * You can select the input terminal by pressing the input switch of the monitor. Input mode Video PC D-SUB PC D-sub input terminal PC HDMI PC/AV HDMI input terminal AV HDMI PC/AV HDMI input terminal When the PN-ZB01 (optional) is attached Input mode Video PC DVI-D PC/AV DVI-D input terminal PC HDMI PC/AV HDMI input terminal...
nSwitching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE ZOOM 1 ZOOM 2 NORMAL Dot by Dot TIPS • Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright Law, so please be careful. • When dual-screen display is selected, the screen size cannot be changed. • The appearance of the original video may change if you select a screen size with a different aspect ratio than the original image (e.g. TV broadcast or video input from external equipment). • When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen size to “NORMAL”.
Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 21 to 24 for details of each menu items. Caution • Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings. nExample of operation (Adjusting CONTRAST in the PICTURE menu) MENU 1. Press to display the menu screen. SCREEN SCREEN PICTURE AUTO CLOCK AUDIO PHASE H-POS SETUP V-POS H-SIZE OPTION V-SIZE...
Menu item details The menu will differ depending on the input mode. nSCREEN AUTO (PC D-SUB/PC RGB) The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. Pressing performs adjustment. Use this automatic adjustment when you use the PC D-sub input terminal or PC RGB input terminals to display a PC screen for the first time or when you change the setting of the PC. (See page 26.) CLOCK (PC D-SUB/PC RGB) Adjusts frequency for sampling clock for applicable video. Adjust when there is flickering in the form of vertical stripes. When using the adjustment pattern (see page 26), make adjustments so that no vertical stripe noise appears in it. PHASE (PC D-SUB/PC RGB) Adjusts sampling clock phase for applicable video. Useful when small characters appear with low contrast and/ or there are flickers at corners.
Menu Items nAUDIO TREBLE Adjusts the volume of treble-level sound. BASS Adjusts the volume of bass-level sound. BALANCE Adjusts the balance of the audio sound between right and left. RESET Resets the values of the AUDIO menu items to the factory preset values. MENU Select “ON” and then press nSETUP OSD H-POSITION Adjusts the horizontal display position of menu screen. OSD V-POSITION Adjusts the vertical display position of menu screen. MONITOR Select the installation direction of the monitor. LANDSCAPE ...Horizontal orientation PORTRAIT ...Vertical orientation MONAURAL AUDIO Outputs audio signals as monaural. LANGUAGE Sets the display language for the menu screen.
nOPTION DATE/TIME SETTING Set the date and time. Press and time, and press to change the numerical values. Set the date in “Year/Month/Day” order. Set the time on a 24-hour basis. SCHEDULE (See page 25.) You can set the time to switch the monitor on and off. INPUT SELECT Select the input mode to be used in PC/AV DVI-D input terminal, PC/AV HDMI input terminal and PC RGB/AV component input terminals.
Menu Items nPIP/PbyP PIP MODES Sets the display method. OFF ...Displays one screen. PIP ...Displays a sub screen inside a main screen. PbyP ...Displays a main screen and a sub screen in a line. PbyP2 ...Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line. PIP SIZE Sets the size of the sub screen in PIP mode. PIP H-POS Adjusts the horizontal position of the sub screen in PIP mode. PIP V-POS Adjusts the vertical position of the sub screen in PIP mode. PIP BLEND In PIP mode, use this menu item to display the sub screen transparently.
nSCHEDULE You can set the time to switch the monitor on and off. Set this function with “SCHEDULE” in the OPTION menu. (See page 23.) SCHEDULE XXXX/XX/XX XXX XX:XX:XX POWER DAY OF THE WEEK 1 9 2 0 x 1 0 8 0 V: 60 Hz H: 67.5 kHz 1. Press to select the SCHEDULE number, and press 2.
Menu Items nADVANCED items (AV input) (See page 21 for additional Menu item details.) FLESH TONE Adjust the hue control. 3D-NR Reduce the noise of playback images on video. Setting a higher level reduces more noise. However, it may cause blurring on an image. MPEG-NR Reduce block noise caused by digital compression.
Initialization (Reset)/Functional Restriction Setting (FUNCTION) You can return the settings to their factory-preset values and restrict operations. SIZE 1. Hold down until “F” appears in the upper left corner of the screen. 2. While “F” appears, press order. FUNCTION ALL RESET ADJUSTMENT LOCK UNLOCKED RS-232C OSD DISPLAY TEMPERATURE ALERT STATUS ALERT POWER BUTTON CONTROLLER INPUT...
Controlling the Monitor with a PC (RS-232C) You can control this monitor from a PC via RS-232C (COM port) on the PC. You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 29), you can make input mode selection/adjustment or can check the status of a specific monitor. Precautions when the PN-ZB01 (optional) is attached • To control the monitor via RS-232C, set RS-232C/LAN SELECT to RS-232C. • You cannot use RS-232C and LAN control simultaneously. PC connection nOne-to-one connection with a PC Connect with RS-232 straight cable between the PC’s COM port (RS-232C connector) and the RS-232C input terminal on the monitor.
nResponse code format When a command has been executed correctly Return code , 0A A response is returned after a command is executed. * If an ID number has been assigned Space (20 ID number of responding monitor When a command has not been executed Return code , 0A * If an ID number has been assigned Return code Space (20 ID number TIPS • “ERR” is returned when there is no relevant command or when the command cannot be used in the current state of the monitor.
Controlling the Monitor with a PC (RS-232C) nCommands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 IDST ... A monitor receiving this command sets its own ID number in the parameter field. Example: IDST0001 OK 001 ← The ID number of this monitor is set to 1. TIPS You can automatically assign ID numbers by using the IDST command with the Repeater control (see “Repeater control”...
nRepeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers. [Example] Set 1 Set 2 * If monitors are connected as shown above, you can execute a command like “Set all monitors’...
Controlling the Monitor with a PC (RS-232C) RS-232C command table How to read the command table Command: Command field (See page 28.) Direction: W When the “Parameter” is set in the parameter field (see page 28), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obtained by setting “????”, “ (repeater control) in the parameter field (see page 28). Parameter: Parameter field (See page 28.) Reply: Response (Returned value) *1: “●” indicates a command which can be used in power standby mode regardless of the STANDBY MODE setting.
Controlling the Monitor with a PC (RS-232C) SETUP menu Function Command OSD H-POSITION OSDH OSD V-POSITION OSDV MONITOR STDR MONAURAL AUDIO MONO LANGUAGE LANG POWER ON DELAY PWOD STANDBY MODE STBM OFF IF NO OPERATION ATOF HDMI SETTING HDMI AUTO VIEW HDAW HDMI RGB INPUT HDRA RANGE HOT PLUG CONTROL (DVI) HPCT HOT PLUG CONTROL (HDMI) HPCH RS-232C/LAN SELECT CTLS ID NUMBER ID NO. SETTING IDST ID NO. SETTING...
OPTION menu Function Command Direction DATE/TIME SETTING DATE SCHEDULE SC01- SC08 INPUT SELECT DVSL BNSL HDMI HDSL AUDIO SELECT PC DVI-D ASDP PC HDMI ASHP PC D-SUB ASAP PC RGB ASCP AV DVI-D ASDA AV HDMI ASHA AV COMPONENT ASCA AV S-VIDEO ASSA AV VIDEO ASVA INPUT RESOLUTION CHECK PXCK RESOLUTION PIXEL SETTING PXSL (PC) (PC D-SUB, PC RGB)
Controlling the Monitor with a PC (RS-232C) PIP/PbyP menu Function Command PIP MODES MWIN PIP SIZE MPSZ PIP POS THE LONGEST MHPS DIRECTION THE SHORTEST MVPS DIRECTION PIP POS LD+SD BATCH MPOS PIP BLEND MWBL PIP SOURCE MWIP SOUND CHANGE MWAD MAIN POS (Main screen) MWPP PbyP2 POS (Sub screen) MW2P AUTO OFF MOFF Initialization/Functional Restriction Setting (FUNCTION) menu Function Command ALL RESET...
Others Function Command Direction SCREEN SIZE (PC) WIDE SCREEN SIZE (AV) WIDE VOLUME VOLM MUTE MUTE INFORMATION MODEL INF1 SERIAL NO SRNO BRIGHT VLMP TEMPERATURE SENSOR DSTA TEMPERATURE ACQUISITION ERRT CAUSE OF LAST STANDBY MODE STCA Commands for setting of the GAMMA user data Function Command Direction RED GAMMA DATA TRANSFER UGRW GREEN GAMMA DATA TRANSFER UGGW BLUE GAMMA DATA TRANSFER UGBW RED GAMMA DATA READ...
Controlling the Monitor with a PC (LAN) When the PN-ZB01 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. You can also configure the monitor to send e-mail notification when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through). LAN terminal LAN cable (commercially available, straight) TIPS • You must assign an IP address to the monitor by following the procedures in “Settings to connect to a LAN”. (See the description on the right.) • Your PC must be installed with Internet Explorer (version 6.0 or later). • To control the monitor via LAN, set RS-232C/LAN SELECT to LAN. (See page 22.) • You cannot use RS-232C and LAN control simultaneously. Initializing personal information • When the PN-ZB01 (optional) is attached, personal information such as e-mail addresses can be registered in the monitor. Before transferring or disposing of the monitor,...
■ To set from a PC When the monitor is connected to a PC, LAN settings can be configured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC’s IP address (3) Configure the monitor’s LAN settings (1) Connecting your monitor to a PC Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor. LAN terminal To LAN terminal LAN cable (commercially available, crossover) (2) Specifying the PC’s IP address To configure the monitor’s LAN settings, you must temporarily change the settings on the PC. This explanation is based on Windows 7. 1. Log on to the PC with an administrator account. 2. Click [Start], and then click “Control Panel”.
Controlling the Monitor with a PC (LAN) 5. Click on “LAN SETUP” under NETWORK. 6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to “OFF”, specify an IP address. SUBNET MASK If the DHCP CLIENT is set to “OFF”, specify the subnet mask. DEFAULT GATEWAY If the DHCP CLIENT is set to “OFF”, specify the default gateway. If you are not using a default gateway, specify “0.0.0.0”. 7. When the setting is changed, click [Apply]. 8. Check the message and click [OK]. 9. Exit Internet Explorer. 10. Restore the PC’s IP address jotted in Step 6, “(2) Specifying the PC’s IP address”.
■ INFORMATION Information about this monitor appears. ■ CONTROL You can control the operations corresponding to the buttons POWER INPUT SIZE ) on the remote control unit. (See page 18.) TIPS • In standby mode, Power ON is the operation available. • MONITOR POWER turns the monitor power ON/ OFF regardless of the POWER BUTTON setting in the FUNCTION menu. Controlling the Monitor with a PC (LAN) ■ ADJUSTMENT You can adjust these settings which are also available on the monitor’s menu. • SCREEN (See page 21.) • PICTURE (See Page 21.) • PICTURE (ADVANCED) (See Page 26.) • AUDIO (See page 22.)
Controlling the Monitor with a PC (LAN) ■ NETWORK (LAN SETUP) This screen allows you to set the settings necessary when the monitor is connected to a LAN. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”. IP ADDRESS If the DHCP CLIENT is set to “OFF”, specify an IP address. SUBNET MASK If the DHCP CLIENT is set to “OFF”, specify the subnet mask.
■ NETWORK (GENERAL) This screen allows you to specify the general LAN settings. MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen. AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specify in minutes from 1 to 65535. A value of ‘0’ will disable this function. DATA PORT Specify the TCP port number to use for exchanging data with the monitor.
Controlling the Monitor with a PC (LAN) ■ MAIL (RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error. RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notification e-mail CONDITION Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting. CONFIRMATION Sends test e-mail. This allows you to confirm that the e-mail settings are configured properly. Attach the log file to a TEMPERATURE/HARDWARE error e-mail. When this option is checked, a log is added to the mail which notifies a temperature or status error. TIPS • The RECIPIENT E-MAIL ADDRESSES can be up to 64 alphanumeric characters or symbols.
■ SNMP You can configure settings related to SNMP. SNMP SETTING Set whether to enable or disable SNMP. VERSION Set the version of the SNMP to be supported. COMMUNITY NAME 1 to 3 Set the name of the community required for the access. USER 1 to 3 Set the user name, password, authentication method and other options required for access. TRAP SETTING Set whether to enable or disable the trap function.
Power LED flashes red. “STATUS [xxxx]” appears in the corner of the screen. • Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer. (When STATUS ALERT is set to OSD & LED. This varies depending on the setting.) The touch panel power LED lights red. • Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer.
The monitor, however, will enter standby mode again if the cause of the temperature rise is not eliminated. (See page 6.) - C heck whether the monitor is placed at a location where a quick rise in temperature is likely. Internal temperature rises quickly if the vents on the monitor are blocked. - I nternal temperature rises quickly if dust accumulates inside the monitor or around the vents. Remove dust if possible. Ask Sharp dealer about removing internal dust. Troubleshooting...
* / standby mode * Dimensions (excluding protrusions) Weight Cannot be used simultaneously. Does not support plug and play. Temperature condition may change when using the display together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments. In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied. When AUTO INPUT CHANGE is set to OFF. When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 1.0 W As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. Specifications PN-L601B 60" Class [60-1/16 inch (152.5cm) diagonal] TFT LCD (pixels) 1920 x 1080 Approx. 1.06 billion colors 0.692 mm (H) × 0.692 mm (V) 160° right/left/up/down (contrast ratio ≥ 10) (mm) 52-5/16 x 29-7/16 (1329.1 x 747.6) Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω] Horizontal/vertical separate (TTL: positive/negative), Sync-on-green, Composite sync (TTL: positive/negative) NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM VESA DDC2B VESA DPMS, DVI DMPM Digital HDMI x 1...
4-1/8  55-5/8  2-13/16 [71.5] Opening width (52-11/16 ) When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or more the weight of the monitor. nPower management This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor’s power management function to work.