Download
Share
Print this page
Yardistry YM11895 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Yardistry Manuals
  4. Outdoor Furnishing
  5. YM11895
  6. Installation and operating instructions manual

Yardistry YM11895 Installation And Operating Instructions Manual

10' x 10' gazebo
Hide thumbs

Advertisement

Quick Links

Download this manual
10' x 10' GAZEBO
Installation and Operating Instructions – YM11895
HEIGHT:
9'4" or 2.85m
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Revised 09-14-2023
9' 11-1/8"
12'-1 5/32"
3.03 m
3687.1
Yardistry – North America
Toll Free Customer Support:
9' 11-1/8"
12'-1 5/32"
3687.1
3.03 m
1.888.509.4382
info@yardistrystructures.com
www.yardistrystructures.com
Y40000-1895
1
support@yardistrystructures.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the YM11895 and is the answer not in the manual?

Questions and answers

Related Manuals for Yardistry YM11895

Summary of Contents for Yardistry YM11895

  • Page 1 10’ x 10’ GAZEBO Installation and Operating Instructions – YM11895 HEIGHT: 9’4” or 2.85m IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY Revised 09-14-2023 9‘ 11-1/8” 12'-1 5/32" 3.03 m 3687.1 Yardistry – North America Toll Free Customer Support: 9‘ 11-1/8”...

  • Page 2: Important Safety Notice

    Wood is NOT flame retardant and will burn. Grills, fire pits and chimneas are a fire hazard if placed too close to a Yardistry structure. Consult user’s manual of the grill, fire pit or chimnea for safe distances from combustible materials.
  • Page 3 Limited Warranty Yardistry warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. In addition, for any product with lumber, all lumber is warranted for five (5) years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable.
  • Page 4 Instructions for Proper Maintenance Your Yardistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it.

  • Page 5: Assembly Tips

    Assembly Tips Following are some helpful tips to make the assembly process smooth and efficient. PRE-ASSEMBLIES: (i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc) • Work on a raised, solid and flat surface such as, a table or saw horse. •...
  • Page 6 Permanent Installation Examples Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Pergola Room. We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure to a pre-existing or new wood or concrete surface.
  • Page 7 Permanent Installation Examples cont. Concrete Patio [min. 10’ 1-7/8” x 10’ 1-7/8” (3.096 m x 3.096 m)] with 6” (15.24 cm) clearance on all sides Anchoring Hardware not included Wood Deck [min. 10’ 1-7/8” x 10’ 1-7/8” (3.096 m x 3.096 m)] with 6”...

  • Page 8: Part Identification

    Part Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 139.7 x 139.7 x 2235.2mm (5½ x 5½ x 88") 4pc. (752) - Post Y70142-752 34.9 x 165.1 x 926.9mm (1-3/8 x 6-1/2 x 36-1/2") 34.9 x 165.1 x 926.9mm (1-3/8 x 6-1/2 x 36-1/2") 4pc.

  • Page 9: Hardware Identification

    Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 4pc. - Short Panel Left 4pc. - Long Panel Right (Y01033-223) (Y01033-224) 1pc. - Roof Panel Set 4pc.
  • Page 10 Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 5/16 x 1-1/4" 36pc. Hex Bolt - (Y07718-311) 12pc. 1/4 x 2-3/4 Hex Bolt - (Y07718-223) 12pc.
  • Page 11 • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department. PRODUCT NUMBER: YM11895 CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1) CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2) CARTON I.D.
  • Page 12 Step 2: Post Assemblies A: At the bottom of each (752) Post insert two 5/16” T-Nuts as shown in fig. 2.1 and 2.2. B: At the bottom of each (752) Post place two Post Mounts tight to the bottom and inside faces as shown in fig. 2.1 and 2.2.

  • Page 13: Step 3: Beam Assembly

    Step 3: Beam Assembly Part 1 A: Connect one (725) Left Outside Beam and one (726) Right Outside Beam using two 5/16 x 1-1/4” Hex Bolts (with 5/16” lock washer, 1/4 - 5/16” large washer and 5/16” t-nut) as shown in fig. 3.1 and 3.2. B: Connect one (727) Inside Short Beam to each end of one (728) Inside Long Beam using two 5/16 x 1-1/4”...
  • Page 14 Step 3: Beam Assembly Part 2 D: Place one Outside Beam Assembly on one Inside Beam Assembly so the ends are flush. Match the bolt holes in each (727) Inside Short Beam and (728) Inside Long Beam with the bolt holes in (725) Left Outside Beam and (726) Right Outside Beam.
  • Page 15 Step 4: Frame Assembly and Anchoring Part 1 A: Move your Post Assemblies to the final location. Make sure the ground is flat and level before continuing assembly. B: With one person at each Post stand two complete Post Assemblies. A third person places one Beam Assembly against the outside of each Post, flush to the tops and outside corners.
  • Page 16 Step 4: Frame Assembly and Anchoring Part 2 D: Make sure each corner is square and level then attach Beam Assemblies to Post Assemblies with two 5/16 x 4-3/4” Lag Screws (with 1/4-5/16” large washer) per corner. (fig. 4.4) E: Depending on what you are placing the Gazebo on will determine how you anchor it to that surface. Please refer to pages 6 and 7 for installation examples.
  • Page 17 Step 5: Attach Gussets Note: The bevelled ends on each gusset should always face away from the wood it is attaching to. A: Make sure the assembly is still square and level then facing one Beam Assembly place one (740) Short Right Gusset on the right hand side so the top fits tight to the Beam Assembly and the bottom fits tight to the Post Assembly.
  • Page 18 Step 6: Fascia Beam Assembly A: Tightly connect one (731) Fascia Left Short and one (730) Fascia Right Short using one 5/16 x 1-1/4” Hex Bolt (with 5/16” lock washer, 1/4-5/16” large washer and 5/16” t-nut) as shown in fig. 6.1 and 6.2. B: Repeat Step A three more times to make four Fascia Beam Assemblies.
  • Page 19 Step 7: Roof Rafter Assembly Part 1 A: On each side of one (736) Rafter place one (729) Corner LT and one (737) Corner RT so the tops and edges are flush then attach with two #8 x 2” Wood Screws per side. (Fig. 7.1 and 7.2) B: Place Fascia Beam Assembly from Step 6 on the bottom of (729) Corner LT, (737) Corner RT and (736) Rafter so the sides are flush then attach with one #8 x 2”...
  • Page 20 Step 7: Roof Rafter Assembly Part 2 D: Place one (732) Short Strap in the notches of (729) Corner LT, (737) Corner RT and (736) Rafter so the ends do not overhang the outside edges of the outside boards then attach with six #8 x 1-1/2” Wood Screws. (Fig.
  • Page 21 Step 8: Attach Roof to Beam Brackets A: On the back of three Roof Rafter Assemblies place one Rafter Beam Bracket on each (734) Rafter Short Right, (735) Rafter Short Left and (736) Rafter. Loosely attach each bracket to rafters with one 1/4 x 2” Hex Bolt (with two 1/4-5/16”...

  • Page 22: Handle With Care

    STOP STOP STOP STOP INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! HANDLE WITH CARE! Place roofing material on a non-abrasive surface before assembly as it can bend, dent and scratch easily. WARNING – DO NOT OVER TIGHTEN ROOFING SCREWS! Over tightening screws will cause roofing material to crush.
  • Page 23 STOP STOP STOP STOP INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! BE SURE TO REMOVE ALL PLASTIC COVERING, ON BOTH SIDES OF THE ALUMINUM PANELS AND TRIM, DIRECTLY BEFORE INSTALLING EACH PIECE. (One side is clear and the other is blue, both must be removed.) Example #1 Example #2 Overtightened and Crushed...
  • Page 24 Step 9: Attach Roof Panels Part 1 A: Place one Long Panel Left on the front of one Roof Rafter Assembly so it is flush to the side of (729) Corner LT and a slight overhang at the bottom of the Fascia Beam Assembly. Holes should line up with (736) Rafter. (fig.
  • Page 25 Step 9: Attach Roof Panels Part 2 E: Place one Short Panel Left on Roof Rafter Assembly so it overlaps the Long Panel Left and it is flush to the sides of (729) Corner LT and a slight overhang at the bottom of the Fascia Beam Assembly. There should be no overhanging at the corners.
  • Page 26 Step 10: Attach Ridge Clips and Roof Edges A: Place one Roof Edge Left and one Roof Edge Right on the bottom of each Roof Rafter Assembly so the ends are flush with the outside ends of the Fascia Beam Assembly and meet tight in the centre. Attach both Roof Edges with 13 #8 x 1”...
  • Page 27 Step 11: Attach Roof Panels to Frame Part 1 A: From inside of Post Assemblies measure 4’ 1-7/16” (1.26 m) to mark the centre of each Beam Assembly. (fig. 11.1) B: With all four assemblers place one Roof Panel Assembly with Rafter Beam Brackets just in front of the Post Assemblies then raise it up so the middle Rafter Beam Bracket is lined up with the centre mark.
  • Page 28 Step 11: Attach Roof Panels to Frame Part 2 C: Lift a second Roof Panel Assembly with Rafter Beam Brackets over Beam Assembly taking care not to drag the panel on the beams. Make sure the middle Rafter Beam Bracket lines up to the centre mark and (729) Corner LT and (737) Corner RT are flush with each other.
  • Page 29 Step 11: Attach Roof Panels to Frame Part 3 E: Lift third Roof Panel Assembly with Rafter Beam Brackets over Beam Assembly taking care not to drag the panel on the beams then set in place beside the second panel. Make sure the middle Rafter Beam Bracket lines up to the centre mark.
  • Page 30 Step 12: Roof Peak Assembly A: Insert Carriage Bolt through the top of Peak Cap, into Peak Post then Spring Clip. The Spring Clip holds the assembly together. (fig. 12.1) B: Insert 1/4” Nut into Peak Loop. Be careful nut is loose and will fall out until attached to Peak Cap Assembly. (fig.
  • Page 31 Step 13: Attach Roof Peak to Roof Panels A: Insert Roof Peak Assembly in gap between Roof Panels. Peak Cap to be lined up with (729) Corner LT and (737) Corner RT. (fig. 13.1 and 13.2) B: Insert both Roof Peak Brackets through Carriage Bolt and attach Peak Loop to Carriage Bolt and twist to tighten loosely.
  • Page 32 Step 14: Attach Final Roof Panel Part 1 A: Lift last Roof Panel Assembly (without Rafter Beam Brackets) over Beam Assembly taking care not to drag the panel on the beams. Panel fits under the Peak Cap, push up on Peak Loop to lift Peak Cap. The centre of the other panels may have to be pushed up to fit fourth panel.
  • Page 33 Step 14: Attach Final Roof Panel Part 2 Remember to push up centre to assist with alignment. C: Starting at the bottom and working up loosely connect Roof Panel Assemblies through (729) Corner LT and (737) Corner RT with three 1/4 x 2-3/4” Hex Bolts (with two 1/4-5/16” large washers and one 1/4” lock nut) per side.
  • Page 34 Step 14: Attach Final Roof Panel Part 3 A: On the fourth Roof Rafter Assembly, place one Rafter Beam Bracket on each (734) Rafter Short Right, (735) Rafter Short Left and (736) Rafter. Loosely attach each bracket to rafters with one 1/4 x 2” Hex Bolt (with two 1/4- 5/16”...
  • Page 35 Step 15: Secure Roof Corners A: Make sure middle Rafter Beam Brackets are lined up over centre mark and all are flush and tight to the Beam Assemblies. (729) Corner LT and (737) Corner RT should be aligned with mitre in Beam Assembly Lift in centre if needed to adjust Roof Panel Assemblies.
  • Page 36 Step 16: Attach Corner Caps A: At each corner place one Corner Cap tight to Fascia Assemblies, push up so the bottom is tight to the bottom of the assemblies then attach with four #8 x 3/4” Sheet Metal Screws per Corner Cap. (fig. 16.1 and 16.2) Fig.
  • Page 37 Step 17: Secure Rafter Beam Brackets A: From inside the assembly attach Rafter Beam Brackets to Beam Assemblies and rafters with four #10 x 1-1/4” Pan Screws per bracket. (fig. 17.1 and 17.2) B: Tighten all bolts in Rafter Beam Brackets. (fig. 17.1 and 17.2) Fig.
  • Page 38 Step 18: Secure Roof Peak Brackets A: Tighten the two screws in Roof Peak Brackets then attach to (729) Corner LTs and (737) Corner RTs in the remaining holes with fourteen #10 x 1-1/4” Pan Screws. (fig. 18.1) Fig. 18.1 Roof Peak Bracket Roof Peak...
  • Page 39 Step 19: Attach Ridge Caps to Roof Panels A: Slide one Ridge Cap over the Ridge Clips, with cut end leading, on each corner of the assembly from the bottom up, lifting Peak Cap by pushing up the Peak Loop so Ridge Caps fit under Peak Cap then attach with two #8 x 3/4”...
  • Page 40 Step 20: Attach Twist Brackets A: Measure 5-3/4”(146.1 mm) down from the inside of each (752) Post, place bottom of either 45° Twist Bracket LT or 45° Twist Bracket RT at measured location then attach to (752) Post and (729) Corner LTs and (737) Corner RTs with four #10 x 1-1/4”...
  • Page 41 Step 21: Metal Hooks and Plaque Part 1 A: Two 50 mm Hooks are included with this unit for attaching wiring. They can be placed anywhere along the (729) Corner LTs and (737) Corner RTs as needed. Pre-drill with a 1/8” drill bit before installing. (fig.
  • Page 42 Step 21: Metal Hooks and Plaque Part 2 B: Attach Gazebo ID Plaque to a prominent location on your gazebo with two #10 x 1-1/4” Pan Screws. This provides warnings concerning safety and important contact information. A tracking number is provided to allow you to get critical information or order replacement parts for this specific model.
  • Page 43 NOTES support@yardistrystructures.com...
  • Page 44 Atención a: Servicio de Atención al Cliente À l’attention de: Service à la clientèle Yardistry would like to say “Thank you” for your time and feedback. Yardistry quiere “Agradecerle” por su tiempo y su opinión. Yardistry aimerait vous remercier d’avoir pris le temps de répondre au sondage.
  • Page 45 Ensemble de moustiquaire MERIDIAN 10’ x 10’ Instructions d’installation – YM11753 Revised 12-13-2018 Yardistry – North America Yardistry – Norteamérica Yardistry – Amérique du Nord Toll Free Customer Support: 1.888.509.4382 Línea gratuita de servicio al cliente: 1.888.509.4382 Service client sans frais: 1.888.509.4382 info@yardistrystructures.com info@yardistrystructures.com...
  • Page 46 Netting is NOT flame retardant and will burn. Grills, fire pits and chimineas are a fire hazard if placed too close to a Yardistry structure. Consult user’s manual of the grill, fire pit or chimnea for safe distances from combustible materials.

  • Page 47: Instructions For Proper Maintenance

    • Tape Measure If you dispose of your Yardistry structure: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards at the time it is discarded. Be sure to follow your local waste ordinances.
  • Page 48 Part Identification - Identificación de las piezas - Identification des pièces Y00400-005 Y70818-258 (2) - Insect Panel (2 pack) - Panel Mosquitero (paquete de 2) - Panneau pour insecte (pqt de 2) (1) - #2 x 2" Robertson Bit - Mecha Robertson No.2 x 2" Y09991-600 - Mèche Robertson #2 x 2"...
  • Page 49 Step 1: Inventory Parts - Paso 1: Piezas del inventario - Étape 1 : Inventaire des pièces STOP ARRÊT PARE Este es el momento en que This is the time for you to Il est temps pour vous de debe hacer el inventario inventory all your hardware faire l’inventaire de toute de todos los tornillos y...
  • Page 50 Step 2: Attach Curtain Tracks - Paso 2: Fijación de la guía de cortina - Étape 2: Fixation du rail pour rideaux Instructions - Instrucciones - Instructions A: From the inside of the A: Desde el interior del ensamble, A: Depuis l’intérieur de assembly, tight against one Post apretado contra uno Ensamble del l’assemblage, bien appuyé...
  • Page 51 Step 2: Attach Curtain Tracks - Paso 2: Fijación de la guía de cortina - Étape 2 : Fixation du rail pour rideaux Images - Fotos - Images Beam Assembly / Ensamble de Viga / F2.2 F2.1 Beam Assembly / Assemblage de poutre Ensamble de Viga / Side View / Vista lateral / Vue de côté...
  • Page 52 Attach Track Gusset -Short Long Track Side Assembly x2 Step 3: Attach Curtain Track Gussets - Paso 3: Fijación de los refuerzos de las guías de cortina - Étape 3 : Fixation des goussets de rail pour rideaux A: Where each set of Curtain A: Donde se une cada juego de A: Là...
  • Page 53 Step 4: Attach End Screws - Paso 4: Fijación de los tornillos de los extremos Insect Screen Inst - Fasten #8 x 2.5" screws -(optional) - Étape 4 : Fixation de vis d’extrémité A: If there is a gap between the A: Si queda un espacio entre A: S’il y a un espace entre le rail Curtain Track Short and the Post...
  • Page 54 Step 5: Attach Tie Back Ribbons - Paso 5: Colocación de los lazos traseros - Étape 5: Fixation des rubans d’attache arrière A: On the inside corner of each A: En la esquina interior de cada A: Dans le coin intérieur de Post Assembly attach one Tie Ensamble del Poste, fije un Lazo chaque assemblage de montant,...
  • Page 55 Step 6: Attach Insect Panel Part 1 - Paso 6: Fijación de panel mosquitero Parte 1 - Étape 6: Fixation du Panneau pour insecte Partie 1 A: Starting at the centre of one A: Comenzando por el centro de A: En débutant au centre de l’un Beam Assembly attach one Insect un Ensamble de Viga, fije un Panel des assemblages de poutre, fixez un...
  • Page 56 Step 6: Attach Insect Panel Part 2 - Paso 6: Fijación de panel mosquitero Parte 2 - Étape 6: Fixation du panneau pour insecte Partie 2 C: Join Insect Panels by zipping C: Una los Paneles Mosquiteros C: Joignez les panneaux pour them together.
  • Page 57 Step 7: Attach Insect Panels to Posts - Paso 7: Fijación de los paneles mosquiteros a los postes - Étape 7 : Fixation des panneaux pour insecte aux montants A: At the top of each Post A: En la parte superior de cada A: Au haut de chaque Assemblage Assembly locate Button Snaps Ensamble del Poste, ubique los...
  • Page 58 Step 8: Secure Insect Panels - Paso 8: Sujeción permanente de los paneles mosquiteros - Étape 8 : Pose des panneaux pour insectes Note: Only complete this step Nota: Realice este paso solo si Note: Complétez cette étape if you plan on keeping your planea dejar colocados los paneles uniquement si vous planifiez de Insect Panels up at all times.
  • Page 59 Garantía Limitada - Garantie limitée Yardistry warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. In addition, for any product with lumber, all lumber is warranted for five (5) years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable.
  • Page 60 NOTES support@yardistrystructures.com...
  • Page 61 NOTES support@yardistrystructures.com...
  • Page 62 Atención a: Servicio de Atención al Cliente À l’attention de: Service à la clientèle Yardistry would like to say “Thank you” for your time and feedback. Yardistry quiere “Agradecerle” por su tiempo y su opinión. Yardistry aimerait vous remercier d’avoir pris le temps de répondre au sondage.