Voxx Electronics DIRECTWIRE DIRECTECHS DS3 Installation Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Functions compatible with the 2019 Hyundai Santa Fe

*Telematics features: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart Pro.

* Odometer

3x LOCK START (Start control using OEM Remote)

3x LOCK STOP (Stop control using OEM Remote)

Accessory Activation

Arm Factory Security

Brake Status (foot brake)

Control of aftermarket alarm with OEM remote

Disarm Factory Security

Door Lock Control

Door Locks Status

Door Unlock

Driver Priority Unlock

DS4+/DS3+/VSM3 Only

E-Brake Status

THHYN3-DS4+,DS3+-ONLY Compatible

Entry Monitoring ALL Door Pins

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

Fuel level/EV battery level

Ignition Activation

Ignition Status

Immobilizer Bypass-Data No Key Req'd

Parking Lights Control

Remote Start Takeover

SmartStart

Start (Crank) Activation

Tach / RPM Output

Trunk / Hatch Release

933.HK18

v1.18.198.12

2019 Hyundai Santa Fe

(Sold Separately)

Table of Contents

Need help?

Do you have a question about the DIRECTWIRE DIRECTECHS DS3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Voxx Electronics DIRECTWIRE DIRECTECHS DS3

Page 1 933.HK18 v1.18.198.12 2019 Hyundai Santa Fe THHYN3-DS4+,DS3+-ONLY Compatible (Sold Separately) Functions compatible with the 2019 Hyundai Santa Fe *Telematics features: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart Pro. * Odometer Entry Monitoring ALL Door Pins 3x LOCK START (Start control using OEM Remote) Entry Monitoring Hood Pin 3x LOCK STOP (Stop control using OEM Remote)
Page 2: Table Of Contents
Contents Introduction Pre-installation and application warnings Installation Wiring diagram with T-Harness (THHYN3 Rev.1) Wiring diagram with T-Harness (THHYN3 Rev. 2) Wiring diagram Locating components in the vehicle Vehicle connections Module programming Module programming for convenience only (skip transponder) Module programming for security-only installations Pairing remotes Connecting the module 8556T Temperature Sensor...
Page 3: Introduction
Introduction This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a digital configuration requires the module to be flashed with vehicle-specific firmware. Refer to our website (www.directechs.com) and click on the DIRECTLINK text in the header for additional information.
Page 4: Pre-Installation And Application Warnings
Pre-installation and application warnings This section highlights important information for this specific firmware and will assist in pricing accordingly, as START HERE well as bringing awareness to any operational or vehicle limitations. Compatibilities and Requirements T-Harness Keys required for Keys required THHYN3 REV.
Page 5: Wiring Diagram With T-Harness (Thhyn3 Rev.1)
Wiring diagram with T-Harness (THHYN3) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( THHYN3 (optional T-Harness) Ignition Switch 1A Diode (1N4002+) (-) Ignition Interrupt Output: Lt. Green/Black Accessory Interr.
Page 6: Wiring Diagram With T-Harness (Thhyn3 Rev. 2)
Wiring diagram with T-Harness (THHYN3 Rev. 2) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( THHYN3 Rev. 2 (optional T-Harness) Ignition Switch 1A Diode (1N4002+) (-) Ignition Interrupt Output: Lt. Green/Black Accessory Interr.
Page 7: Wiring Diagram
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Headlight-Wiper Switch (black conn. at headlight switch) P-CAN High: P-CAN Low: B-CAN Low: White, pin 22 Gray, pin 23 Blue, pin 31 (MUX) Parking Lights:...
Page 9: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2019 Hyundai Santa Fe. Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection...
Page 10 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/18 Orange/Black (+) Instant Trigger Input No Connection H2/19 Blue (-) Trunk Trigger Input No Connection H2/20 Green (-) Door Trigger Input No Connection H2/21 Gray The installation of an aftermarket hood pin is ONLY required on vehicles (-) Hood Switch Input that are NOT equipped with a factory hood pin.
Page 11 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H3/12 (+) 12 Volt Input Ignition Switch, black 6 pin plug, pins 1 and 5 Blue/Orange and White Mandatory (15A) Relay harness, 10-pin white connector (H4) Module Connects To Conn./Pin Color Description...
Page 13: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. skip transponder programming or security-only programming, see following pages. Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift is in the neutral position.
Page 14: Module Programming For Convenience Only (Skip Transponder)
Module programming for convenience features only (skip transponder) Refer to "LED diagnostics and troubleshooting" for more information and for troubleshooting purposes. Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift is in the neutral position. Connect the 12-pin main power harness to the module.
Page 15: Module Programming For Security-Only Installations
Module programming for security-only installations Refer to "LED diagnostics and troubleshooting" for more information and for troubleshooting purposes. Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift is in the neutral position. Connect the 12-pin main power harness to the module.
Page 16: Pairing Remotes
Pairing Remotes and Sensors To enter pairing: Key OUT Key IN Key IN Key IN Turn the vehicle ignition to the ON position. START START START START Within 10 seconds, on the Control Center (antenna) or the LED/Valet Pod (standalone switch), press and release once (1x), and then press and hold &...
Page 17: When Used In Conjunction With Smartstart
before providing power to the Directed SmartStart unit: ® SmartStart with Loops – The brown loop must be cut. SmartStart with Pigtails – The gray wire must be connected to a ground source. Loops Pigtails DO NOT connect the Directed SmartStart 2-pin power harness when using the DS3+/DS4+.
Page 18: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. This system supports manual transmission installations.
Page 19: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power.
Page 20 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
Page 21: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module Programming”. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin main 12-pin harness power harness.
Page 22: Tach Learning Procedure (Not Needed With Virtual Tach)
Tach learning procedure (not needed with Virtual Tach) Data Tach: The procedure is not required as the tach comes preprogrammed. However, it is strongly recommended to learn the exact value of the vehicle for the most consistent and reliable starting and functionality. Hardwired Tach: The procedure is required.
Page 23: Limited Lifetime Consumer Warranty
Limited Lifetime Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or work- manship within the Lifetime from the date of original purchase in the original vehicle, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor.
Page 24: Quick Reference Guide (Customer Copy)
Quick Reference Guide (customer copy) Sending commands to your vehicle Pit stop/idle mode Whether you want to remote start the engine, lock/unlock the doors or pop the trunk, there Stop the vehicle in a safe parking spot and put the gear gear in are 3 possible ways you can send commands to your vehicle, using the: in Park (P).
Page 25 Directed SmartStart Bluetooth compatibility (DS4/DS4+ ONLY) ® ® This system is equipped with a Bluetooth ® version of Directed SmartStart ® offering up to 200' of range. The simple graphical interface gives you control over the following features of your installed remote start system or security with remote start system: Lock/Arm Š...

This manual is also suitable for:

Directwire directechs ds3+Directwire directechs ds4

Voxx Electronics DIRECTWIRE DIRECTECHS DS3 Installation Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Voxx Electronics DIRECTWIRE DIRECTECHS DS3

Summary of Contents for Voxx Electronics DIRECTWIRE DIRECTECHS DS3

This manual is also suitable for:

Table of Contents