Related Manuals for Waterworld New Millennium
Summary of Contents for Waterworld New Millennium
- Page 1 Installation & Service Manual 5- Stage Reverse Osmosis Drinking Water System with Booster Pump Assembled in USA...
- Page 2 Congratulations on choosing the Millennium® 5-Stage Reverse Osmosis (RO) Drinking Water System This high quality unit has been designed to fit under most kitchen and wet-bar sinks. We suggest that you carefully review the following information booklet before you attempt to install the reverse osmosis system. Your Reverse Osmosis system is a highly sophisticated machine.
- Page 3 INSTALLATION DIAGRAM FOR MILLENNIUM® RO SYSTEM (shown with standard faucet) Sink JGF-PP3212U7W (Faucet Connector) JGV-ASVPP1LF (Angled Stop Valve) 3/8” Blue Tubing to Faucet Cold Water Feed Supply DS-EZW4 (Drain Saddle) 1/4” Green Tubing 1/4” Red Rubing from Flow Restrict to Drain Clamp Stage 5: Carbon Post Filter 3/8”...
- Page 4 INSTALLATION DIAGRAM FOR MILLENNIUM® RO SYSTEM (shown with optional air gap faucet) Sink JGF-PP3212U7W (Faucet Connector) 3/8” Red Tubing JGV-ASVPP1LF from Faucet to 3/8” Blue Tubing (Angled Stop Valve) Drain Clamp to Faucet DS-EZW6 Cold Water (Drain Saddle) Feed Supply 1/4”...
-
Page 5: Installation Kit
Installation Kit 1. Color Coded Tubing: ( 4 coils, 4 colors) ¼’’ Green Tubing (approximately 6 feet) ¼’’ Red Tubing (approximately 6 feet) 3/8’’ Yellow Tubing (approximately 6 feet) COLOR TUBING 3/8’’ Blue Tubing (approximately 6 feet) Optional 5th coil is added for air gap installations 3/8’’... - Page 6 TAPPING INTO THE COLD WATER LINE (Using the water supply adaptor Part # JGV-ASVPP1LF) For flex metal or plastic line. NOTE: The Millennium® RO system must be connected to the COLD water supply only. 1) Turn off the cold water supply to the sink faucet by locating the round or oblong handle and turning clockwise until the water supply is off.
-
Page 7: Tools Required
Tools Required: 1) Hand drill for faucet hole. Use the appropriate bit for the surface you are drilling. (½” for non air gap faucets and - 7/8” drill bit for air gap ones). A) Titanium bit for metal sinks. B) Glass and tile bit or Relton cutter for porcelain sinks. C) Diamond core bit for granite. -
Page 8: Mounting The Faucet
MOUNTING THE FAUCET Standard Faucet 1) Drill a ½” hole in the sink or the counter top, or use an existing hole. 2) Slide chrome cover plate and rubber gasket on to stem of faucet and place faucet onto sink, with the stem going through the hole. -
Page 9: Drain Clamp Installation
COMPRESSION CONNECTIONS A compression fitting may be found with the faucet. To make the connections, slide a compression nut onto the tubing. Slip the white plastic sleeve onto the Connector tubing with the beveled end towards the end of the tubing. Insert a brass or plastic insert into the tubing, bottom the tubing into the fitting, slide the nut up and White Plastic Sleeve tighten with a wrench. - Page 10 EZ FITTINGS- QUICK CONNECT Your Millennium® RO system is equipped with EZ fittings. The quick connect fittings feature leak proof installations. EZ Fittings provide efficient quick connection and disconnection resulting in reduction of service time and labor cost. 1 Cut tubing square Cut the tube square.
-
Page 11: Start-Up Procedure
START UP PROCEDURE 1) Check to see all connections are made 2) Check that the pre-filter and pre-carbon sumps are secure with o-rings in place using the housing wrench provided. 3) Slowly turn on the water by turning the needle valve counterclockwise or ball valve 1/4 turn,where handle is parallel to the tubing line. -
Page 12: Recommended Maintenance
NOTE: MINIMUM PRESSURE REQUIRED TO OPERATE YOUR MILLENNIUM® SYSTEM IS 40 PSI. A BOOSTER PUMP ASSEMBLY IS REQUIRED WHEN FEED PRESSURE DROPS BELOW 40 PSI. IMPORTANT NOTES-MUST READ: 1) All Millennium RO system has been thoroughly tested at our factory. The system ®... -
Page 13: Replacement Components
NOTE: ALWAYS MAKE SURE THAT O-RINGS ARE SEATED PROPERLY INSIDE SUMPS BEFORE TIGHTENING CANISTERS. Replacement Components*: Model 1st Stage 2nd Stage 3rd Stage 4th Stage 5th Stage Head Assembly Millennium DB-10-05 CTX-10-05 CTX-10-05 PTRO-1812-75 OMNP-K2540-BB SYS-MILL110-HA *Subject to change without notice Stage 1) Sediment filter: This Pre-filter protects the system by reducing sediment from the water supply before entering the Carbon Blocks and TFC membrane. -
Page 14: Troubleshooting
TROUBLESHOOTING SYMPTOM CAUSE CORRECTION NOTES: 1) TURN WATER SUPPLY ON. 1) WATER SUPPLY IS TURNED OFF. 2) CHECK TO MAKE SURE FEED VALVE IS NOT CLOGGED. 2) NOT ENOUGH WATER PRESSURE TO SYSTEM. 1) CHECK FEED WATER PRESSURE. MUST BE AT LEAST 10PSI. 3) PREFILTERS CLOGGED. -
Page 15: Conditions For Operation
MILLENNIUM® LIMITED WARRANTY Congratulations on the purchase of your WW-USA Water System. WW-USA warrants that the Products identified below are free from material defects in materials and workmanship. Any defective part will be replaced at no charge for the part if any fail- ure caused by the defect occurs within the following time periods originating from the date of original system installation. - Page 16 Assembled in USA...