Related Manuals for Waterworld Proline QC RO
Summary of Contents for Waterworld Proline QC RO
- Page 1 Instruction Manual Read this instruction manual to properly install and operate this system.
-
Page 2: Table Of Contents
Content Product and Accessories Installation Schematic Diagram Installation Instructions Cartridge Replacement Trouble Shooting Precautions for Use Technical Specifications and Water Treatment Process Flow Diagram Warranty... -
Page 3: Product And Accessories
Product and Accessories Main Body Four Filter Cartridges Includes spun PP filter(PP), block carbon filter (CTO), reverse osmosis membrane (RO) and post activated carbon filter (T-33). One Accessory Box Includes faucet, 3-way ball valve, three pieces of tubing, instruction book, adapter and drain clamp. Reference Images for Accessories. Faucet Faucet connector 3-Way ball valve... -
Page 4: Installation Schematic Diagram
Installation Schematic Diagram Tap water faucet RO faucet Dust cover Power Flush Tap water pipe 4 filter cartridges Select Reset Display content and buttons POWER WATER FLUSH LACK Inlet TDS 3-way ball vavle Outlet TDS Drain water tubing RO water tubing Cartridge life Power Power... -
Page 5: Installation Instructions
Installation Tapping Into The Cold Water Line (Using the water supply adapter 3-way ball valve) For flex metal or plastic line. NOTE: QC-RO system must be connected to the COLD water supply only. 1) Turn off the cold water supply to the sink faucet by locating the round or oblong handle and turning clockwise until the Flex metal or plastic line water supply is off. - Page 6 Mounting The Faucet Standard Faucet 1) Drill a ½” hole in the sink or the counter top, or use an existing hole. 2) Slide chrome cover plate and rubber gasket on to stem of faucet and place faucet onto sink, with the stem going through the hole. 3) Place metal slotted washer over threaded stem of faucet.
- Page 7 Drain Clamp Installation Sink 1) The drain clamp assembly should be installed above the trap and on the vertical or horizontal tail piece. Mount drain saddle at either location Never mount here 2) Mark the hole position on the pipe and drill a ¼’’ hole through one side of the pipe.
-
Page 8: Cartridge Replacement
First Use Instruction 1. Connect RO system to the transformer. The power indicator will come on, and you will hear three chimes, the machine will flush for 90 seconds while flushing icon blinks. 2. When the system starts filtering water you will see the computer display real-time TDS numbers, the cartridge life span and power indicator will light on. - Page 9 Filter Cartridges Replacement Steps: Warning: Do not Turn or Flip-Over the RO 1. Cut off water supply to the RO 2. Open Faucet to drain all water inside the RO 3. Turn RO off 4. Remove the cartridges cap 5. Hold the cartridge handle and rotate 90°counterclockwise, then pull it out 6.
-
Page 10: Trouble Shooting
Trouble Shooting Problem Cause Solution Insufficient feed water pressure Increase feed water pressure No power or power failure Power-on Water pump is out of service and system does not work High pressure switch is out of order Replace high pressure switch Pump is blocked and adapter fuse burn-out Replace adaptor and repair water pump TDS of feed water is too high or system is placed... -
Page 11: Precautions For Use
Precautions for Use Attention 1. Flush and replace cartridges regularly. 2. Do not disassemble parts randomly, it may cause water leak or damage the system. 3. Do not use a power supply that does not have the rated voltage. 4. Please pull the power plug and cut off the feed water valve for long term storage. 5. -
Page 12: Technical Specifications And Water Treatment Process Flow Diagram
Technical Specifications and Water Treatment Water Treatment Process Process Flow Diagram Flow Diagram Technical Specifications Technological process Feed water quality: Municipal tap water Feed water PP filter CTO filter Voltage and frequency: 100~240V, 50/60Hz Power input: 24V Purified water flow: .35 gal/min water T33 filter RO filter...