Table of Contents
Advertisement
Quick Links
CS-2205ADVTW1
CONGRATULATIONS on your choice of a Security System by Crimestopper Security Products Inc. This booklet contains
the information necessary for installing, using, and maintaining your CS-2205 Advantage alarm system. If any questions
arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.
This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you
READ THIS MANUAL before beginning your installation.
information contained herein may differ from your vehicle.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren, L.E.D., Power,
Ground, Door Pin, and Flashing Lights etc.
-OPTIONAL: These are features are to be connected only if desired or agreed upon by the customer and the installing
dealer (i.e. Door Locks, Starter Disable, Hood/Trunk Protection and Auxiliary Remote Outputs etc.) These features may also
require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is going to be installed
with your particular system.
TECH SUPPORT
(800) 998-6880
Hours: M-F 8:00AM-4:30PM
Pacific Std. Time
REV B 6.2005
Deluxe 2-Way LED Paging Security System
INSTALLATION & OPERATING INSTRUCTIONS
This device complies with FCC Rules part 15. Operation is subject to the following two
conditions: 1) This device may not cause interference, and (2) this device must accept any
interference that may be received, including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment. Such modification could void the user's authority to operate the
equipment.
SERIES I
This book is provided as a GENERAL GUIDLINE and the
Advertisement
Table of Contents
Related Manuals for CrimeStopper CS-2205
Summary of Contents for CrimeStopper CS-2205
- Page 1 CONGRATULATIONS on your choice of a Security System by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and maintaining your CS-2205 Advantage alarm system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.
-
Page 2: Installation Cautions & Warnings
TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………………………………………...………………………………..2 Suggested Component Mounting………….…………………………………………………………….……………………….…...3 Wiring (Connectors H1-H8)…………………………………………………………………………………………………………3-12 Power Door Lock Wiring...………………………………………………………………..……………………………………….…4-6 Starter Disable Wiring…………………………..…..…………………………………………………………..………………….10-11 Antenna Diagram………………….……...…………………………………………………………………….…...…………………13 Option Programming……………..………………………………………………………..…………..…….……………………14-18 Programmable Option Reset………………………...……….…………………………………………………….…………….….16 Main System Wiring Diagram………………….…………………………………………………………………………………….19 Remote Programming……..……………………………………………………..………………………...………………………..20 Operation.………………………..…………………………………..….……………….…………………………………….……21-32 2-Vehicle Operation…….…………………………………..….………………………………….…….…………………………….23 INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). -
Page 3: Control Module/Component Mounting
CONTROL MODULE/COMPONENT MOUNTING CONTROL MODULE: The alarm control module should be mounted in a concealed location. DO NOT mount the control unit in the engine compartment. Fasten the module to a bracket or wire harness using the cable ties provided. ANTENNA MODULE: For optimum range and performance, the antenna/receiver module should be located high up on the front windshield glass. - Page 4 RED/WHITE WIRE: INPUT SOURCE FOR FLASHING PARKING LIGHT Connect to a +12 Volt source or Chassis Ground depending on the vehicle Parking light circuit. WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT (optional) Connect to switched parking light wire at back of light switch or connect directly to one of the parking lights at the front of the vehicle.
- Page 5 (H 4) POWER DOOR LOCK WIRING DETERMINING DOOR LOCK TYPE: We recommend determining the type of locking system the vehicle has before connecting any wires. Incorrect connection may result in damage to the alarm and/or vehicle locking system. This door lock information is provided as a guide.
- Page 6 (H 4) POWER DOOR LOCK WIRE DIAGRAM...
- Page 7 (H 5) ANTENNA/PAGER SWITCH Transmitter Antenna: Two-way Pager Antenna. Pager switch: Pages your Two-way pager in an event you lose your keys (Two-way pager only) (H 6) KNOCK SENSOR (Optional) KNOCK SENSOR (Optional): Sensor not included in kit. (H 7) PROGRAM/OVERRIDE BUTTON 2-PIN PLUG (LARGE): PROGRAM/OVERRIDE PUSH BUTTON PROGRAM/Emergency Override (Disarm) For Programming:...
- Page 8 (H8) PIN WIRING DIAGRAM 1. Black/White Wire: (-) 200mA Dome light Output (Require a Relay) 2. Black/Violet Wire: (-) 200mA Auxiliary 3 Output (Option, may Require a Relay) 3. Orange/Black Wire: (-) 200mA Factory Disarm (OEM) Output (Option, may Require a Relay) 4.
- Page 9 WIRING 16-PIN CONNECTOR BLACK/WHITE WIRE: DOME LIGHT Illumination Output (Optional, Requires relay) Negative Dome Light System: Connects to terminal 85 of a relay. Connect terminal 86 + 12V Constant. Connect terminal 87 to Chassis Ground and Connect Terminal 30 to the Negative dome light activation. Positive Dome Light System: Connects to terminal 85 of a relay.
- Page 10 ORANGE/WHITE WIRE: NEGATIVE STARTER DISABLE (Normally Open) This wire should be connected to the Orange wire of the pre-wired relay socket for the starter disable. Connect the Yellow wire of the relay socket to the Ignition switched wire on the vehicle. Remove the white wire from the relay socket with a small flat head screwdriver an insert it in pin # 87.
-
Page 11: Starter Disable Diagram
NORMALLY CLOSED STARTER DISABLE SWITCH Yellow (ignition) NORMALLY OPEN STARTER SWITCH Remove white wire from Relay Remove harness from pin (87A) Reinsert it Yellow in pin (87) with a (To ignition) small screwdriver. STARTER DISABLE DIAGRAM START WIRE IGNITION WIRE START WIRE IGNITION WIRE STARTER... - Page 12 VIOLET WIRE: (+) DOOR TRIGGER Connect to Positive type door switches that show +12 Volts when the door is open and Ground when the doors are closed. WHITE/BLACK WIRE: DOOR UNLOCK CONTROL INPUT Connect Door Unlock input from aftermarket switch. This is a negative Door Unlock input that controls the onboard relay for Power Door Unlock output wire.
- Page 13 RECOMMENDED ANTENNA LOCATIONS WINDSHIELD CS-2205ADVTW1 Antenna System Window Mount Antenna Antenna Wire CS-2205ADVTW1...
-
Page 14: Programmable Options
You can program multiple options in one session if you start with the lowest option and continue on to higher options [if needed] without repeating steps #1-3 below. For example, you can follow the programming steps to change Option #2 to “OFF” by pressing the lock button on the remote, then you can continue pressing the program button additional times to get to a high number option and change the setting without having to repeat Steps 1-5. - Page 15 CS-2205 Alarm Option Function TX Button #1 Door & Hood Trigger Horn Pulse Auto lock with Ignition Passive/Active Arming ON = Passive Arm Active Re-Arm Passive Locks Parking Lights on w/Disarm Arm with Ignition ON Siren Chirps w/Arm/Disarm Override PIN Code...
-
Page 16: Programmable Option Reset
PROGRAMMABLE OPTION RESET This system provides a reset method to restore all options to FACTORY DEFAULT VALUES as listed in the “Button #2” column of the programmable option chart on pages 18-19. This can be helpful if you have lost track of the option settings on your system, or when you are moving the system from car to car and want a “clean slate”. - Page 17 7. ARM WITH IGNITION ON: This feature allows the system to arm when the ignition key is on or off, or arm the system with key off only. 8. SIREN CHIRPS WITH ARM/DISARM: With this feature, siren chirps with Arm/Disarm can be programmed either ON or OFF when using the regular Lock/Unlock buttons.
- Page 18 16. ENABLE RANGE CHECK: If this feature is selected, the system will automatically check the range in 60 seconds after arming, then every 20 minutes. 17. TEST MODE: In this test mode, this system can test the Zone 2 (Instant ground trigger), the Zone 3 (Door trigger), and the Zone 1 & Zone 4 (2 stage shock sensor) sensitivity without using the traditional arming/disarming procedures to test the sensors.
- Page 19 Optional pager (Knock) TRANSMITTER Sensor ANTENNA VALET SWITCH PAGER SWITCH 4 Pin 3 Pin 2 pin Black Brown Blue ANTENNA WIRE ADV-2205TW1 2 Pin 6 Pin 4 Pin White White Orange Dual 6 Pin White Zone Connector for Shock Door locks & Sensor Door unlocks Connection...
-
Page 20: Transceiver / Remote Control Programming
TRANSCEIVER / REMOTE CONTROL PROGRAMMING 1. Turn key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times. Press buttons #1 (Lock) & #2 (Unlock) together at the same time of each transceiver to be learned. You should get 2 light flashes indication the unit is waiting for a 2 will flash 3 times indicating its waiting for the 3 unit will automatically exit code learning mode. -
Page 21: Standard Remote
LOCK 2nd CAR OPERATION TRUNK AUX. #1 STANDARD REMOTE Transmitter Button System Function Lock Doors & Arm System Arm and Delete The 2 Stage Shock Sensor. Arm System and Hidden Alarm Function Silent Arming / Disarming Unlock Doors & Disarm System Two Steps Door Unlock &... - Page 22 TWO-WAY LED REMOTE Hood / Trunk Trigger Door Trigger Shock Sensor Trigger Ignition Trigger LED display: Function Disarmed Slow Flash Armed Fast Flash Passive Arming On (Solid) Valet Mode CHIRP INDICATORS: Chirp Function 1 chirp 2 chirps Disarm 3 chirps Ajar Warning 4 chirps Disarm / Triggered...
- Page 23 2-VEHICLE OPERATION: (CS-2205ADVTW1) Second Vehicle Security Operation: Your remote transmitter can be utilized to control a second vehicle security system. To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. All programming parameters are the same except for the following: For Regular Remote Control Transmitter: 1.
-
Page 24: Operation
OPERATION ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and the starter (optional) will be disabled. The red in-dash LED in the vehicle will begin to flash. - Page 25 particular zone will NOT be protected by the alarm. All remaining functioning zones will still be protected if the system remains armed. AUTOLOCK/UNLOCK Autolock / Unlock allow the alarm to control the door locks automatically with the vehicle’s Ignition. When the ignition is turned on, 3 seconds later, the doors will lock.
-
Page 26: Tamper Disarming
TAMPER DISARMING If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times. TWO STEPS DOOR UNLOCK (OPTIONAL) This feature will independently unlock the driver’s door only when disarming the security system. Pushing the second time within 2 seconds will unlock the other doors. DISARMING WITHOUT A TRANSMITTER OVERRIDE THE ALARM WITHOUT PASSWORD PIN CODE (Factory Default Setting) The Override function may be used if the remote transmitter is lost or inoperative. -
Page 27: Car Locator
EXAMPLE: To Override The System With The Password Code 83, you would; 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2. Within 5 seconds, Press and Release the Program/Valet button 8 times 3. Within 15 seconds of the last digit code enter (the 1 4. - Page 28 1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During panic mode, the normal function of this transmitter button will be suspended. The transmitter be used to lock and unlock the door (if the option is installed), however once the disable device, (where installed) will be enable allowing the vehicle to start.
- Page 29 Transceiver Button System Function Program Mode - Button Lock Program Mode - Power Save Mode Program Mode - Switching code for 2nd / 1st Car Operation Press within 5 seconds Program Mode - Demo Mode System’s Status Check Optional Driving Pager Last Trigger Memory Retrieval Button Lock On / off: It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others.
- Page 30 3. To exit programming mode, take no action for five seconds. The remote control will generate two long beeps to indicate programming mode has been exited. System’s Status Check: When you want to check the system’s present status through the 2-Way remote control transceiver, Press the button first, within 3 seconds press the system’s present status will immediately displayed on the LED.
-
Page 31: Battery Replacement
Regular Remote Transmitter: If the range of your transmitter deteriorate, it is possible that you need to replace the battery. 1. Remove upper transmitter case. 2. Remove old battery from transmitter. 3. Install a new battery CR2032 (3 volt) noting the (+) and (-) marks in the battery area of the transmitter. 4. - Page 32 Two “bi” sounds while pressing the button of the remote control transceiver www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2005 Crimestopper Security Products LED on the remote transceiver / Z / LED will pause flashing at the same time for 3 seconds...
Need help?
Do you have a question about the CS-2205 and is the answer not in the manual?
Questions and answers