Pioneer VSX-D1S Operating Instructions Manual page 25

REAR PANEL FACILITIES
[VIDEO OUT)
Connect to the VCR 2 VIDEO INPUT jacks.
[AUDIO OUT (L, R)]
Connect to the VCR 2 AUDIO INPUT jacks.
G) VCR 1 jacks
{VIDEO IN)
Connect to the VCR 1 VIDEO OUTPUT jacks.
[AUDIO IN (L, R))
Connect to the VCR 1 AUDIO OUTPUT jacks.
[VIDEO OUT]
Connect to the VCR 1 VIDEO INPUT jacks.
(AUDIO OUT (L, R)]
Connect to the VCR 1 AUDIO INPUT jacks.
© S (connector) video jacks
When used in conjunction with a VCR, Video disc player (Laserdisc
player) or monitor TV equipped with S video jacks, connect to these
jacks. See page 7.
@ VIDEO ADAPTOR jacks
Use to connect a video adaptor component such as a video enhancer
or color corrector.
CENTER WOOFER OUT jack
If you want to boost the surround center channel low frequencies, or
you want to use the unit in a 3D system, connect to a center woofer
power amplifier.
Frequencies above about 200 Hz are cut at 18 dB/oct.
@) CENTER AMP jacks
{POWER IN]
When a separate pre-amplifier is used for center speaker and this unit
is used as a power amplifier, connect the pre-amplifier to this jack.
[PRE-OUT]
When a separate power amplifier is used to drive the center speaker,
connect the power amplifier to this jack.
REAR AMP jacks
{PRE OUT]
When a separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
[POWER IN]
When a separate pre-amplifier is used for rear speakers and this unit
is used as a power amplifier, connect the pre-amplifier to these jacks.
@) CENTER SPEAKERS terminals
Connecting the surround center channel speaker system(s).
You can connect two speakers for dual center, so you can locate
speakers on both sides of the TV.
Speaker impedance:
Refer to @ POWER/IMPEDANCE SELECTOR switch on page 26.
NOTE:
Do not allow any of the code's conductors to protrude from the
terminals or touch any other conductors. Malfunctioning or breakdown
may occur when conductors come into contact with each other.
@2 REAR SPEAKERS terminals
Connect the rear speakers to these terminals.
Speaker impedance
Connect speaker systems with a nominal impedance of between 8 and
16 Q.
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
@3 PHONO LEVEL control
Use to adjust turntable input level. If distortion occurs when you are
using a high-output cartridge, adjust the volume level until it's the same
as another input, such as TUNER.
GND terminal
Connect the turntable ground lead to this terminal.
@® Audio INPUT jacks
PHONO .............55 Connect to turntable.
COL cas .... Connect to compact disc player.
LINE ........cceeeeeeeee Connect to the audio output jacks of an additional
audio component.
VDP/CDV jacks (input)
[VIDEO IN)
When watching the video image from a LD player (Compatible Laserdisc
player) or a VCR used for playback, connect its VIDEO OUTPUT jack
here.
[AUDIO IN (L.R)]
When playing back the audio channel from a LD player (Compatible
Laserdisc player) or a VCR for playback, connect its AUDIO OUTPUT
jacks here.
@) TV jacks (input)
Use these jacks if wish to connect a TV tuner having both victeo and
audio outputs.
(VIDEO IN]
Connect the TV tuner's VIDEO OUTPUT to this jack.
{AUDIO IN (L, R)]
Connect the TV tuner's AUDIO OUTPUT to these jacks.
VIDEO jacks (input)
Connect the output jacks of video components.
For example, connect a playback-only VCR or a video camera.
(3) VIDEO OUT TO MONITOR TV jacks (output)
Use to connect a monitor TV or a TV set with video input terné nals for
watching program materials from a VCR or Video disc player (Laser Disc
player) connected to this unit.
FRONT AMP jacks
[PRE-OUT]
When a separate power amplifier is used to drive the front speakers,
connect the power amplifier to these jacks.
[POWER IN]
When a separate pre-amplifier is connected and this unit iswised as
power amplifier, connect the pre-amplifier to these jacks.
25
< AR§1272>