Ranger TruSensor TS58R User Manual

Trusensor tire pressure monitoring system diagnostic & service tool

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

TruSensor Tire Pressure Monitoring System

Manual 5900313 - Revision A - March 2023

Model

• TS58R

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

DANGER

Diagnostic & Service Tool

User Guide

Read the entire contents of this manual before using

this product. Failure to follow the instructions and safety

precautions in this manual can result in serious injury or

death. Make sure all other operators also read this manual.

Keep the manual near the product for future reference. By

proceeding with setup and operation, you agree that you

fully understand the contents of this manual and assume

full responsibility for product use.

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free 1 (800) 253-2363

Tel: 1 (805) 933-9970

rangerproducts.com

Table of Contents

Summary of Contents for Ranger TruSensor TS58R

Page 1 1645 Lemonwood Dr. Santa Paula, CA 93060 USA Toll Free 1 (800) 253-2363 Tel: 1 (805) 933-9970 rangerproducts.com TruSensor Tire Pressure Monitoring System Diagnostic & Service Tool User Guide Manual 5900313 - Revision A - March 2023 Model • TS58R Designed and engineered by BendPak Inc.
Page 2 BendPak website. Warranty. The BendPak Ranger warranty is more than a commitment to you: it is also a commitment to the value of your new product. For full warranty details, contact your nearest BendPak Ranger dealer or visit bendpak.com/support/warranty.
Page 3: Table Of Contents
Table of Contents Introduction......3 Sensor Programming by OBD....14 Shipping Information.... 4 Sensor Programming by Activation..Safety Considerations..4 Location (Position) Learning....22 FAQ........6 Remote Key Signal Strength....Specifications...... 7 Log and System Settings......25 Quick Start......9 Device Information and Updates.....
Page 4: Shipping Information
Assistance with your TS-58R is available from your dealer, by calling Ranger at (805) 933-9970, or by emailing support@rangerproducts.com. You may also contact Ranger for parts replacement (please have the serial number and model number of your unit available). This user manual contains instructions and procedures for using the TS58R. The figures and photos used in this guide are samples, and the actual screen may differ depending on the vehicle under test and the software version.
Page 5 Make a visual inspection of the product before using it. Check for damaged or missing parts. Do not use the product if you find problems with the unit. Instead, remove it from service, then contact your dealer, call BendPak Ranger at (805) 933-9970.
Page 6: Faq
Frequently Asked Questions Question: How does the TPMS work? Answer: Each tire in a TPMS contains a pressure/temperature sensor and transceiver. These sensors monitor the tire air pressure and temperature then sends this data to the vehicle’s Electronic Control Unit (ECU) along with the sensor ID number. When the tire pressure falls below factory specifications, the ECU triggers an alert to notify the vehicle operator of a low tire pressure condition.
Page 7: Specifications
Specifications Characteristic TS58R A - Length 8.25 in. / 209.5 mm B - Width 3.75 in. / 95 mm C - Depth 1.5 in. / 38 mm Weight 1.5 lbs. / 680 g Battery 3.7V at 3500 mAh Lithium Polymer Battery Endurance 5 hours continuous use Battery Charging Input...
Page 8 TS58R Control Panel Item Description Function Touch Screen LCD Touch Screen displays menu selections and Display test results. UP Scroll Button Scrolls the selection cursor up. Activation Key Sends the confirmation to wirelessly recognize and program sensors. Right Scroll Button Moves the Selection cursor to the right.
Page 9: Quick Start
TPMS Quick Start Diagnosing and replacing a defective Tire Pressure Sensor with a new TruSensor 1. TPMS Diagnosis, refer to pp. 10-11. a. Press the on-off button for ≈3 seconds to power up the device. b. Select TPMS from the main menu screen. c.
Page 10: Tpms Diagnosis
TPMS Overview Tire pressure monitoring system diagnosis on the TS58R will cover five sections: 1. Basic TPMS Diagnosis Function. Allows wireless reading/scanning of Tire Pressure Sensors. Providing the Sensor status, ID information, Pressure, Temperature and Battery Charge Status. Data available may vary based on sensor type. 2.
Page 11 4. On the next page select TPMS diagnosis, read the guidelines then select confirm on the next page. 5. The driver side front tire will be selected on the display. Hold the TS58R within 10 cm of that tire’s valve stem and press to read the sensor ID and Data.
Page 12: Obd Diagnostic Function
OBD Diagnostic Function This function allows display of the pressure sensor status and determines if the Tire Sensor IDs match the IDs stored on the ECU. 1. Select the make, model, and year, of the vehicle. 2. Connect the OBD Cable to the vehicle’s DLC interface and the TS58R. 3.
Page 13 5. Click Confirm on the touchscreen. The TS58R will automatically read the sensor identification numbers saved on the vehicle’s ECU board and displays them on the screen. Green - ECU Computer Board Pressure Sensor ID and Tire Sensor ID match. Red –...
Page 14: Sensor Programming By Obd
7. Click Clear to automatically clear the fault code and poll the ECU board to ensure all fault codes have been deleted; or click Save to store the fault code. Saved Fault Codes may be viewed in the “data record.” Sensor Programming by OBD This section covers programming the new TruSensor Tire Pressure Sensors.
Page 15 2. Connect the OBD Cable to the Vehicle’s DLC interface connector and turn the ignition to the on position. 3. Click on the Confirm button, the TS58R will read the Tire Pressure Sensor ID saved on the Vehicle’s Control Board and displays it on the TS58R screen. 4.
Page 16 5. Select the Sensor ID and then click on Programming. 6. To continue programming, click Return to repeat steps 3 through 5. TS-58R TPMS Diagnostic Tool 5900313 - Rev. A - March 2023...
Page 17: Sensor Programming By Activation
Sensor Programming-Copy by Activation 1. After Vehicle selection, select Sensor Programming then Copy by Activation. 2. Click Activate or the button to activate the Sensor. TS-58R TPMS Diagnostic Tool 5900313 - Rev. A - March 2023...
Page 18 3. If activation is successful, 4. Place a new TruSensor within 4 in. the OE sensor ID is displayed (10 cm) from the top of the TS58R. at the bottom of the screen. 5. Select Programming, the TS58R will begin to detect nearby TPMS sensors. TS-58R TPMS Diagnostic Tool 5900313 - Rev.
Page 19 SENSOR PROGRAMMING - Manual Input 1. After Vehicle selection, select 2. Enter the 8-digit hexadecimal sensor Sensor Programming then ID number, then select Confirm. Manual Input. 3. Select Confirm to continue the programming process. TS-58R TPMS Diagnostic Tool 5900313 - Rev. A - March 2023...
Page 20 4. Place a new TruSensor within 4 in. (10 cm) of the top of the TS58R. The TS58R automatically detects the nearby sensor. 5. If the Sensor programmed successfully, the Sensor data will be displayed on theTS58R screen. TS-58R TPMS Diagnostic Tool 5900313 - Rev.
Page 21 Sensor Programming – Automatically Generate Sensor ID (1-5) 2. Place all the new TruSensors 1. After Vehicle selection, to be programmed within 4 in. select Sensor (10 cm) of the TS58R. Any quantity Programming then from1 to a maximum of 5 sensors Automatically Create may be programmed.
Page 22: Location (Position) Learning
Location (Position) Learning Three methods are provided to store the TruSensor Location in the Vehicle’s Tire Pressure Module: Stationary, Automatic and OBD. On some vehicles the Location Learning function may be completed by driving the Vehicle. Location Learning - OBD 1.
Page 23 6. Connect the OBD through the 5. Select Relearn. The TS58R will Vehicle’s DLC port, then select prompt the user to connect to Confirm to continue. the Vehicle. 7. If the OBD Learning was 8. Select Erase DTCs to automatically successful, select Confirm to erase the fault code on the vehicle’s display the Sensor ID...
Page 24: Remote Key Signal Strength
Remote Key Signal Strength Test The TS58R can display the signal strength of most vehicle remote keys. To test the remote key’s signal strength: 1. Press the Power Button to initialize the TS58R. 2. Select Auxiliary Function 3. Select Remote Key Test 4.
Page 25: Log And System Settings
1. To access the past test data stored on the TS58R Select Log on the touchscreen. 2. Select Last Test - The TS58R Last Test function displays the last test stored in the Log and allows users to quickly enter the last test interface. 3.
Page 26: Device Information And Updates
Device Information and Software Update To view the current device information: 1. Select Device on the Touchscreen. 2. Select About – Displays device serial number, software, firmware, and TPMS version. To update the TS58R software: 1. Go to www.bendpak.com/trusensor 2. Download the most recent compressed software update file to your computer. 3.
Page 27: Care And Maintenance
Care and Maintenance Storage and handling: Keep in a dry, clean environment. Do not place the device in direct sunlight. Do not place the device in proximity to strong magnetic fields. Keep the device away from liquids such as water or splashing oil. Avoid impact.