Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for unicraft PH 1001
Summary of Contents for unicraft PH 1001
- Page 1 Operating instructions Scissor Pallet Truck PHH 1001 PHH 1001...
-
Page 2: Table Of Contents
6.1 Mounting the drawbar ........7 6.2 Demounting the vent screw........ 8 Fax: 0049 (0) 951 96555 - 55 7 Description of the device........8 E-Mail: info@unicraft.de Internet: www.unicraft.de 8 Before operation............8 9 Operation ..............9 10 Care, maintenance and repair ......10 10.1 Care by cleaning .......... -
Page 3: Introduction
All information and notes in these operating instructions You have made a good choice by purchasing the were summarised while taking applicable standards UNICRAFT palett truck and rules, the state-of-the-art technology and our long- term knowledge and experiences into consideration. -
Page 4: Personal Protective Equipment
Safety CAUTION! Protective gloves This combination of symbol and signal words indi- The protective gloves serve to protect the hands cates a possibly dangerous situation which may against sharp components as well as against fric- lead to minor or light injuries if they are not avoided tion, abrasions or deep injuries. -
Page 5: Safety On The Operation
Intended Use 2.4 Safety on the operation WARNUNG! Do not use a palett truck until you have familiarised - In the event of improper use, no liability is as- yourself with it or been instructed in it. Read the instruc- sumed for possible consequential damage. -
Page 6: Technical Data
Technical Data Technical Data Transport, packaging, storage Delivery 4.1 Table Check the pallet truck for visible transport damage upon delivery. Immediately notify the spedition or retailer if Model PHH 1001 you identify damage on the palett truck. Load-carrying capacity 1000 kg Transport with a crane Load beraring width 540 mm... -
Page 7: Assembly
Assembly Assembly 6.1 Mounting the drawbar Upper position The scissor pallet truck is already pre-assembled. Only Middle position the drawbar has to be mounted as follows. Lower position Fig. 6: Setting the control lever Adjusting the pressure of the valve bracket The pressure of the valve bracket (Pos.7, Fig.7) on the drain valve can be adjusted by using the screw (Pos.10, Fig.7)and the lock nut (Pos.11, Fig.7). -
Page 8: Demounting The Vent Screw
Description of the device Description of the device 6.2 Demounting the vent screw Illustrations in these operating instructions may deviate from For safe transport of the pallet truck the hydraulic sys- the original. tem is equipped with a transport locking screw on the pump housing. -
Page 9: Operation
Operation Operation Set down the pallet truck Lower the fork to the lowest position and place the pallet Safety instructions for operation truck on a level and smooth surface. If equipped with a brake, apply the brake. ATTENTION! Danger to life due to load crash!! Lifting the load Falling loads can lead to serious injuries or even Check that the load does not exceed the capacity of the... -
Page 10: Care, Maintenance And Repair
Care, maintenance and repair 10 Care, maintenance and repair Lowering the load ATTENTION! Risk of injury! ATTENTION! Do not place body parts (hands, feet) under the - Maintenance and repair work may only be carried forks or between the scissors when a load is lifted or out by qualified personnel. -
Page 11: Maintenance Plan
Troubleshooting If the pallet truck is used very frequently or regularly under "difficult operating conditions" (e.g. in particularly Screw plug, dusty environments, under the influence of chemicals or oil filler neck vapours, etc.), the inspection should be carried out at shorter intervals. -
Page 12: Disposal, Recycling Of Used Tools
Disposal, recycling of used tools 12 Disposal, recycling of used tools 13.1 Spare parts order The spare parts may be purchased with the authorised In your own interest and to protect the environment dealer or directly with the manufacturer. Please find the make sure that all machine components are exclusively corresponding contact data in Chapter 1.2 Customer disposed of in as intended and permitted. -
Page 13: Spare Parts Drawings
Spare parts 13.2 Spare parts drawings The following drawings are intended to identify the required spare parts in the event of service. If applicable, submit a copy of the parts drawing including the highlighted components to your authorised retailer. Spare parts drawing 1: Pump Fig. - Page 14 Spare parts Spare parts drawing 2: Fork Fig. 14: Spare parts drawing 2 - Fork PHH 1001 | Version 2.03...
- Page 15 Spare parts Spare parts drawing 3: Drawbar Fig. 15: Spare parts drawing 3 - Drawbar PHH 1001 | Version 2.03...
-
Page 16: Ec Declaration Of Conformity
According to machine directive 2006/42/EC Annex II 1.A Stürmer Maschinen GmbH Manufacturer/distributing company: Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt herewith declares that the following product ® Unicraft Werkstatttechnik Product group: Scissor Pallet Truck Machine type: PHH 1001 Designation of the machine: 6150100... - Page 17 Notes 15 Notes PHH 1001 | Version 2.03...
- Page 18 www.unicraft.de...